Junghwan Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Junghwan Han has a total of 73 co-authors. Here are the top co-authors by number of shared publications:
- Juhui Jeong
Department of Radio and Information Communication Engineering, Chungnam National University, Daejeon, South Korea
7 shared publications - Kuduck Kwon
Kangwon National University
5 shared publications Heeseon Shin
Samsung Electronics Company Ltd., Hwaseong 18448, South Korea
3 shared publicationsKuduck Kwon
Department of Electronics Engineering, Kangwon National University, Chuncheon, Korea
3 shared publicationsPilsung Jang
Samsung Electronics Company Ltd., Hwaseong 18448, South Korea
3 shared publicationsSegyeong Kim
Department of Radio and Information Communication Engineering, Chungnam National University, Daejeon, South Korea
3 shared publications
Latest Publications
- Open Access
- 16 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 26129-26139
280- μ W MICS/MedRadio CMOS Receiver Front-End for In-Vivo Biomedical Implants
This study presents an ultra-low power radio frequency receiver (RX) front-end implemented in complementary metal-oxide-semiconductor (CMOS) technology, designed for operation within the 401–406 MHz Medical Implant Communications Service (MICS) and Medical Device Radiocommunications Service (MedRadio) bands. The proposed direct-conversion RX front-end architecture incorporates a transconductance-boosted current-reuse low-noise amplifier with a feedforward capacitive-coupling technique, in-phase and quadrature complementary current-bleeding downconversion mixers with body voltage control, a two-stage passive-type polyphase filter and local oscillator buffers for quadrature LO signal generation, and output buffers. These techniques collectively enhance the overall RX front-end gain and power efficiency under constrained current consumption. Fabricated in a 65-nm CMOS technology, the implemented RX front-end occupies an active area of 0.16 mm2 (0.64 mm × 0.25 mm), excluding bonding pads. The design achieves input return losses (S11s) better than –10 dB, a conversion gain of 32.3 dB, a noise figure below 4.1 dB, an input 1-dB compression point greater than –35.5 dBm, and an input-referred third-order intercept point greater than –25.5 dBm across the targeted MICS/MedRadio band. The RX front-end draws a current of approximately 280 μA from a 1 V nominal supply.
- 16 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 26129-26139
Open Access280- μ W MICS/MedRadio CMOS Receiver Front-End for In-Vivo Biomedical Implants
This study presents an ultra-low power radio frequency receiver (RX) front-end implemented in complementary metal-oxide-semiconductor (CMOS) technology, designed for operation within the 401–406 MHz Medical Implant Communications Service (MICS) and Medical Device Radiocommunications Service (MedRadio) bands. The proposed direct-conversion RX front-end architecture incorporates a transconductance-boosted current-reuse low-noise amplifier with a feedforward capacitive-coupling technique, in-phase and quadrature complementary current-bleeding downconversion mixers with body voltage control, a two-stage passive-type polyphase filter and local oscillator buffers for quadrature LO signal generation, and output buffers. These techniques collectively enhance the overall RX front-end gain and power efficiency under constrained current consumption. Fabricated in a 65-nm CMOS technology, the implemented RX front-end occupies an active area of 0.16 mm2 (0.64 mm × 0.25 mm), excluding bonding pads. The design achieves input return losses (S11s) better than –10 dB, a conversion gain of 32.3 dB, a noise figure below 4.1 dB, an input 1-dB compression point greater than –35.5 dBm, and an input-referred third-order intercept point greater than –25.5 dBm across the targeted MICS/MedRadio band. The RX front-end draws a current of approximately 280 μA from a 1 V nominal supply.
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (7) , 1053-1056
28-GHz Body-Effect-Controlled CMOS Bidirectional Active Mixer
This work presents a 28-GHz complementary metal-oxide-semiconductor (CMOS) bidirectional mixer for frequency conversion in both receiver (RX) (forward) and transmitter (TX) (backward) modes. The design utilizes the symmetric source-drain structure of CMOS devices, with a supply-switching technique for bidirectional operation. Body-effect control and gain-boosting techniques are also applied to enhance performance in both modes. The proposed design was fabricated using the 65-nm CMOS process and primarily characterized in the 28-GHz band.
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (7) , 1053-1056
28-GHz Body-Effect-Controlled CMOS Bidirectional Active Mixer
This work presents a 28-GHz complementary metal-oxide-semiconductor (CMOS) bidirectional mixer for frequency conversion in both receiver (RX) (forward) and transmitter (TX) (backward) modes. The design utilizes the symmetric source-drain structure of CMOS devices, with a supply-switching technique for bidirectional operation. Body-effect control and gain-boosting techniques are also applied to enhance performance in both modes. The proposed design was fabricated using the 65-nm CMOS process and primarily characterized in the 28-GHz band.
- 18 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (4) , 568-572
Cryogenic CMOS Active Mixer Employing Transformer-Based Current-Bleeding Technique
This brief presents a cryogenic complementary metal-oxide-semiconductor (CMOS) active mixer designed to achieve low-noise and low-power characteristics at cryogenic temperatures. The proposed design employs a transformer-based current-bleeding (CB) technique that further enhances both the conversion gain and noise performance of the mixer when compared to the conventional CB approaches. Implemented as a double-balanced active mixer, the design was fabricated using a 65-nm CMOS process and validated across the 4-8 GHz frequency range under both cryogenic and room temperatures.
- 18 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (4) , 568-572
Cryogenic CMOS Active Mixer Employing Transformer-Based Current-Bleeding Technique
This brief presents a cryogenic complementary metal-oxide-semiconductor (CMOS) active mixer designed to achieve low-noise and low-power characteristics at cryogenic temperatures. The proposed design employs a transformer-based current-bleeding (CB) technique that further enhances both the conversion gain and noise performance of the mixer when compared to the conventional CB approaches. Implemented as a double-balanced active mixer, the design was fabricated using a 65-nm CMOS process and validated across the 4-8 GHz frequency range under both cryogenic and room temperatures.
- Open Access
- 30 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 61556-61567
Blocker-Tolerant Broadband CMOS Low-Noise Amplifier Employing N-Path Filter-Based Load
This study proposes a broadband complementary metal-oxide semiconductor (CMOS) low-noise amplifier (LNA) with intrinsic band-selective out-of-band (OB) blocker rejection capabilities. The proposed LNA design utilizes a differential four-phase N-path filter as the amplifier load to offer a substantial total load impedance difference between the in-band (IB) and OB frequency bands. This ensures that the LNA design securely accomplishes a high-quality-factor frequency selectivity response with lower radio frequency signal losses and its OB rejection performance is maintained against process, voltage, and temperature variations, compared with the case of using the N-path filter as a signal path. To validate its blocker-tolerable performance, the designed LNA was fabricated using a 65-nm CMOS technology and was primarily characterized in the frequency division duplexing bands of the long-term evolution and fifth-generation new radio standards, spanning from 1.7 to 2.7 GHz. The implemented design consistently achieved a transmitter leakage rejection greater than 17 dB across all target frequency bands from several samples. Furthermore, the design attained IB voltage gains greater than 36.4 dB and 40.4 dB, noise figures (NFs) of 1.78 dB and 1.5 dB, OB input 1-dB compression point greater than –27.0 dBm and –26.7 dBm, and full-/half-duplexing OB input-referred third-order intercept points greater than 4.1/3.8 dBm and 4.8/5.0 dBm at the mid- and high-bands, respectively. The OB-induced NF degradation was maintained at less than 0.7 dB. A total bias current of 37.7 mA was required with a nominal supply voltage of 1.2 V. The occupied active area of the implemented design was approximately 0.77 mm2, excluding the bonding pads and input/output cells.
- 30 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 61556-61567
Open AccessBlocker-Tolerant Broadband CMOS Low-Noise Amplifier Employing N-Path Filter-Based Load
This study proposes a broadband complementary metal-oxide semiconductor (CMOS) low-noise amplifier (LNA) with intrinsic band-selective out-of-band (OB) blocker rejection capabilities. The proposed LNA design utilizes a differential four-phase N-path filter as the amplifier load to offer a substantial total load impedance difference between the in-band (IB) and OB frequency bands. This ensures that the LNA design securely accomplishes a high-quality-factor frequency selectivity response with lower radio frequency signal losses and its OB rejection performance is maintained against process, voltage, and temperature variations, compared with the case of using the N-path filter as a signal path. To validate its blocker-tolerable performance, the designed LNA was fabricated using a 65-nm CMOS technology and was primarily characterized in the frequency division duplexing bands of the long-term evolution and fifth-generation new radio standards, spanning from 1.7 to 2.7 GHz. The implemented design consistently achieved a transmitter leakage rejection greater than 17 dB across all target frequency bands from several samples. Furthermore, the design attained IB voltage gains greater than 36.4 dB and 40.4 dB, noise figures (NFs) of 1.78 dB and 1.5 dB, OB input 1-dB compression point greater than –27.0 dBm and –26.7 dBm, and full-/half-duplexing OB input-referred third-order intercept points greater than 4.1/3.8 dBm and 4.8/5.0 dBm at the mid- and high-bands, respectively. The OB-induced NF degradation was maintained at less than 0.7 dB. A total bias current of 37.7 mA was required with a nominal supply voltage of 1.2 V. The occupied active area of the implemented design was approximately 0.77 mm2, excluding the bonding pads and input/output cells.
- Open Access
- 30 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 135295-135303
CMOS Variable-Gain Low-Noise Amplifier Adopting Transformer-Based Noise Cancelling Technique for 5G NR FR2 Applications
This study presents a complementary metal–oxide–semiconductor (CMOS) variable-gain low-noise amplifier (VGLNA) employing a transformer-based noise cancelling technique, applicable for fifth-generation new radio frequency range 2 communication. In the proposed design, gain controllability is realized by combining the in-phase main and current-steering path signals through a transformer load whose coupling coefficient is less than unity. Additionally, the noise contribution from cascode devices can be diminished through a transformer-based noise cancelling technique in low-gain modes. Consequently, an enhanced noise performance is achieved as the gain of the VGLNA is lowered. The proposed design is fabricated in a 65-nm CMOS process. At 28 GHz, the implemented VGLNA attains gains and noise figures of 12.1 to 2.7 dB and 3.55 to 4.3 dB, respectively. The design draws a bias current of 10.6 mA with a 1 V nominal supply and occupies a die size of 0.13 mm2, excluding bonding pads.
- 30 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 135295-135303
Open AccessCMOS Variable-Gain Low-Noise Amplifier Adopting Transformer-Based Noise Cancelling Technique for 5G NR FR2 Applications
This study presents a complementary metal–oxide–semiconductor (CMOS) variable-gain low-noise amplifier (VGLNA) employing a transformer-based noise cancelling technique, applicable for fifth-generation new radio frequency range 2 communication. In the proposed design, gain controllability is realized by combining the in-phase main and current-steering path signals through a transformer load whose coupling coefficient is less than unity. Additionally, the noise contribution from cascode devices can be diminished through a transformer-based noise cancelling technique in low-gain modes. Consequently, an enhanced noise performance is achieved as the gain of the VGLNA is lowered. The proposed design is fabricated in a 65-nm CMOS process. At 28 GHz, the implemented VGLNA attains gains and noise figures of 12.1 to 2.7 dB and 3.55 to 4.3 dB, respectively. The design draws a bias current of 10.6 mA with a 1 V nominal supply and occupies a die size of 0.13 mm2, excluding bonding pads.
- 26 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (10) , 3902-3906
Dual-Band CMOS Down-Conversion Mixer Adopting Band-Switchable Transformer
In this brief, a dual-band complementary metal-oxide-semiconductor (CMOS) down-conversion mixer is presented, which supports the fifth-generation new radio frequency bands of 26-30 GHz and 37-40 GHz. In the proposed design, the transformer-based inductance adjustment techniques are utilized to handle dual-band radio frequency and local oscillator (LO) signals for performance optimization. The proposed design is fabricated using a 65-nm CMOS process. With an identical LO power of +5 dBm, the implemented down-conversion mixer attains conversion gains of 7.1 dB and 5.1 dB, noise figures of 9.6 dB and 11.4 dB, input 1-dB compression points of -14.7 dBm and -11 dBm, and input third-order intercept points of -5.1 dBm and -1.95 dBm for 28 and 39 GHz frequency bands, respectively. The implemented design consumes the current of 6.2 mA with a 1-V supply.
- 26 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (10) , 3902-3906
Dual-Band CMOS Down-Conversion Mixer Adopting Band-Switchable Transformer
In this brief, a dual-band complementary metal-oxide-semiconductor (CMOS) down-conversion mixer is presented, which supports the fifth-generation new radio frequency bands of 26-30 GHz and 37-40 GHz. In the proposed design, the transformer-based inductance adjustment techniques are utilized to handle dual-band radio frequency and local oscillator (LO) signals for performance optimization. The proposed design is fabricated using a 65-nm CMOS process. With an identical LO power of +5 dBm, the implemented down-conversion mixer attains conversion gains of 7.1 dB and 5.1 dB, noise figures of 9.6 dB and 11.4 dB, input 1-dB compression points of -14.7 dBm and -11 dBm, and input third-order intercept points of -5.1 dBm and -1.95 dBm for 28 and 39 GHz frequency bands, respectively. The implemented design consumes the current of 6.2 mA with a 1-V supply.
- 8 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (6) , 695-698
28-GHz Bidirectional RF CMOS Amplifier Employing Body-Effect Control
This letter presents a 28-GHz bidirectional amplifier that operates as a low-noise amplifier (LNA) and a drive amplifier in the receiver (RX) (forward) and transmitter (TX) (backward) modes, respectively. In the proposed design, the bidirectional operation is realized through supply switching (SS) by utilizing the symmetric structure of a complementary metal–oxide–semiconductor (CMOS) device. Additionally, the body voltage control of an n-type MOS (nMOS) device is applied to attain symmetric and enhanced performance in both the forward and backward operations. The proposed design was fabricated using the 65-nm CMOS process and primarily characterized in the 28-GHz band. It achieves a nearly identical performance in both the forward and backward modes.
- 8 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (6) , 695-698
28-GHz Bidirectional RF CMOS Amplifier Employing Body-Effect Control
This letter presents a 28-GHz bidirectional amplifier that operates as a low-noise amplifier (LNA) and a drive amplifier in the receiver (RX) (forward) and transmitter (TX) (backward) modes, respectively. In the proposed design, the bidirectional operation is realized through supply switching (SS) by utilizing the symmetric structure of a complementary metal–oxide–semiconductor (CMOS) device. Additionally, the body voltage control of an n-type MOS (nMOS) device is applied to attain symmetric and enhanced performance in both the forward and backward operations. The proposed design was fabricated using the 65-nm CMOS process and primarily characterized in the 28-GHz band. It achieves a nearly identical performance in both the forward and backward modes.
- Open Access
- 20 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 7739-7750
Calibration-Free Blocker Rejection Broadband CMOS Low Noise Amplifier for Advanced Cellular Applications
This study presents a broadband complementary metal-oxide semiconductor (CMOS) low noise amplifier (LNA), containing out-of-band (OB) blocker rejection capability without an additional calibration process. In the proposed design, separate all-pass and band-stop filter stages are provided in parallel as main and auxiliary paths, respectively, whose amplitude and phase variations are identically tracked by each other over a process, voltage, and temperature dependency. By appropriately combining an in-band signal and OB blockers passed through those filter blocks, robust OB blocker rejection can be realized in the wide frequency range. The designed LNA incorporates a pre-amplifier stage for broad input matching and low-noise characteristics, an N-path filter-based frequency selective stage, and a combiner stage to suppress undesired OB blockers. The designed calibration-free OB blocker rejection broadband LNA is fabricated in a 65 nm CMOS technology and mainly characterized in long-term evolution frequency division duplexing bands, ranging from 0.7 to 2.7 GHz. The demonstrated design consistently attains transmitter leakage and other OB blocker rejection of more than 22.8 dB and 16 dB in low-band (LB) (0.7-1 GHz) and mid- and high-band (MB and HB) (1.7-2.7 GHz) frequency range from several samples without extra gain or phase adjustment, respectively. The implemented LNA also achieves gains of 10.5-11.0 dB and 8-10 dB, noise figures of 3.7-4.1 dB and 3.8-4.9 dB, OB third-order intercept points greater than 8.2 dBm and 9.8 dBm, and OB 1-dB compression points greater than -5.2 dBm and -5.5 dBm, for LB and MB/HB, respectively. The implemented design consumes a total bias current of 23.9 mA with a nominal supply of 1.2 V and occupies an active area of 0.53 mm 2 , excluding bonding pads.
- 20 January 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 7739-7750
Open AccessCalibration-Free Blocker Rejection Broadband CMOS Low Noise Amplifier for Advanced Cellular Applications
This study presents a broadband complementary metal-oxide semiconductor (CMOS) low noise amplifier (LNA), containing out-of-band (OB) blocker rejection capability without an additional calibration process. In the proposed design, separate all-pass and band-stop filter stages are provided in parallel as main and auxiliary paths, respectively, whose amplitude and phase variations are identically tracked by each other over a process, voltage, and temperature dependency. By appropriately combining an in-band signal and OB blockers passed through those filter blocks, robust OB blocker rejection can be realized in the wide frequency range. The designed LNA incorporates a pre-amplifier stage for broad input matching and low-noise characteristics, an N-path filter-based frequency selective stage, and a combiner stage to suppress undesired OB blockers. The designed calibration-free OB blocker rejection broadband LNA is fabricated in a 65 nm CMOS technology and mainly characterized in long-term evolution frequency division duplexing bands, ranging from 0.7 to 2.7 GHz. The demonstrated design consistently attains transmitter leakage and other OB blocker rejection of more than 22.8 dB and 16 dB in low-band (LB) (0.7-1 GHz) and mid- and high-band (MB and HB) (1.7-2.7 GHz) frequency range from several samples without extra gain or phase adjustment, respectively. The implemented LNA also achieves gains of 10.5-11.0 dB and 8-10 dB, noise figures of 3.7-4.1 dB and 3.8-4.9 dB, OB third-order intercept points greater than 8.2 dBm and 9.8 dBm, and OB 1-dB compression points greater than -5.2 dBm and -5.5 dBm, for LB and MB/HB, respectively. The implemented design consumes a total bias current of 23.9 mA with a nominal supply of 1.2 V and occupies an active area of 0.53 mm 2 , excluding bonding pads.