Al Jumlat Ahmed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Al Jumlat Ahmed has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Sheik Mohammad Kazi Nazrul Islam
Institute for Superconducting and Electronic Materials, Australian Institute for Innovative Materials, University of Wollongong, North Wollongong, Australia
4 shared publications - Xiaolin Wang
Institute for Superconducting and Electronic Materials, Faculty of Engineering and Information Sciences University of Wollongong Wollongong New South Wales Australia
3 shared publications - Cara Maxwell Doherty
Manufacturing CSIRO Clayton South 3169 VIC Australia
2 shared publications - Ridwone Hossain
Institute for Superconducting and Electronic Materials (ISEM), Australian Institute of Innovative Materials (AIIM), University of Wollongong, North Wollongong, New South Wales 2500, Australia
2 shared publications - Shahriar Al Hossain
Australian Institute for Bioengineering and Nanotechnology (AIBN), The University of Queensland, Brisbane, Queensland 4072, Australia
2 shared publications - Yusuke Yamauchi
Nagoya University
2 shared publications
Latest Publications
- Open Access
Thermoelectric MOFs and Machine Learning Databases for Prediction of Next Generation Materials
Electrically conducting metal–organic frameworks (MOFs) have been studied over the last two decades and more recently research has gained interest on thermoelectric applications due to their ultra‐low thermal conductivity, which is attributed to their porous structure. Only a handful of intrinsically conducting MOFs and composite MOFs with conducting materials have been reported as thermoelectric materials. Here, thermoelectric MOFs have been comprehensively reviewed to prepare a dataset of 399 materials based on experimental observations. Each data point comprises 12 variables, which can be divided into two broad categories: the MOF's chemical and physical properties (composition, metal node, organic ligand, and crystal structure) and their thermoelectric properties (electrical conductivity, Seebeck coefficient, thermal conductivity, power factor, and figure of merit), which four are target variables of machine learning (ML) models. The dataset has been pre‐processed to streamline it. Six ML models, including Decision Tree, Random Forest, and Gradient Boosting, were trained on the dataset, and the Decision Tree‐based models can predict the electrical conductivity and Seebeck coefficient with high accuracy using the provided information in the dataset on thermoelectric MOF materials. The trained models using the thermoelectric MOFs dataset have been used to explore the thermoelectric parameters of 248 conductive MOFs, which have not yet been explored as thermoelectric materials. image
Open AccessThermoelectric MOFs and Machine Learning Databases for Prediction of Next Generation Materials
Electrically conducting metal–organic frameworks (MOFs) have been studied over the last two decades and more recently research has gained interest on thermoelectric applications due to their ultra‐low thermal conductivity, which is attributed to their porous structure. Only a handful of intrinsically conducting MOFs and composite MOFs with conducting materials have been reported as thermoelectric materials. Here, thermoelectric MOFs have been comprehensively reviewed to prepare a dataset of 399 materials based on experimental observations. Each data point comprises 12 variables, which can be divided into two broad categories: the MOF's chemical and physical properties (composition, metal node, organic ligand, and crystal structure) and their thermoelectric properties (electrical conductivity, Seebeck coefficient, thermal conductivity, power factor, and figure of merit), which four are target variables of machine learning (ML) models. The dataset has been pre‐processed to streamline it. Six ML models, including Decision Tree, Random Forest, and Gradient Boosting, were trained on the dataset, and the Decision Tree‐based models can predict the electrical conductivity and Seebeck coefficient with high accuracy using the provided information in the dataset on thermoelectric MOF materials. The trained models using the thermoelectric MOFs dataset have been used to explore the thermoelectric parameters of 248 conductive MOFs, which have not yet been explored as thermoelectric materials. image
- Open Access
- 27 February 2025
- Published by Wiley in Advanced Materials Technologies
- Vol. 10 (12)
Facile Synthesis of a Carbon Nano Dot‐Based Wearable Flexible Thermoelectric Device
A facile method of synthesizing flexible thin films of carbon nano dots (CNDs) and Polyvinyl Pyrrolidone (PVP) on cellulose based substrates is developed and their thermoelectric properties are demonstrated through the fabrication of a wearable device. Alongside enhanced thermoelectric performance, the CND thin films are biocompatible, low cost and scalable, all essential criteria for wearable thermoelectric devices. A critical window of the CND loading concentration on the cellulose‐based substrate is observed, with significantly enhanced Seebeck coefficient and Power Factor of thin films, demonstrating that the trade‐off principles for thermoelectric materials must be carefully tuned. The highest Seebeck coefficient of –358.45 µV·K−1, power factor of 0.03 µW·m−1·K−2 and the lowest thermal conductivity of 0.086 W·m−1·K−1 at room temperature is achieved with a CND loading concentration of 9.32 g cm−2. A wearable thermoelectric device is fabricated using n‐type CND films with copper electrodes. When worn, the device can generate voltage and current of ≈70 mV and ≈15 nA, respectively, at ΔT of 10 K.
- 27 February 2025
- Published by Wiley in Advanced Materials Technologies
- Vol. 10 (12)
Open AccessFacile Synthesis of a Carbon Nano Dot‐Based Wearable Flexible Thermoelectric Device
A facile method of synthesizing flexible thin films of carbon nano dots (CNDs) and Polyvinyl Pyrrolidone (PVP) on cellulose based substrates is developed and their thermoelectric properties are demonstrated through the fabrication of a wearable device. Alongside enhanced thermoelectric performance, the CND thin films are biocompatible, low cost and scalable, all essential criteria for wearable thermoelectric devices. A critical window of the CND loading concentration on the cellulose‐based substrate is observed, with significantly enhanced Seebeck coefficient and Power Factor of thin films, demonstrating that the trade‐off principles for thermoelectric materials must be carefully tuned. The highest Seebeck coefficient of –358.45 µV·K−1, power factor of 0.03 µW·m−1·K−2 and the lowest thermal conductivity of 0.086 W·m−1·K−1 at room temperature is achieved with a CND loading concentration of 9.32 g cm−2. A wearable thermoelectric device is fabricated using n‐type CND films with copper electrodes. When worn, the device can generate voltage and current of ≈70 mV and ≈15 nA, respectively, at ΔT of 10 K.
- 15 March 2021
- Published by Wiley in Advanced Electronic Materials
- Vol. 7 (4) , 2001044
Significant Reduction in Thermal Conductivity and Improved Thermopower of Electron‐Doped Ba1–xLaxTiO3 with Nanostructured Rectangular Pores
Electron‐doped BaTiO3 is a less studied n‐type metal oxide thermoelectric material. In this work, the electrical conductivity of BaTiO3 samples has been improved by introducing La to yield an n‐type Ba1–xLaxTiO3 semiconducting material. Density functional theory calculations show that the optimal electron‐doping occurs at x = 0.2, and this is also confirmed experimentally. To improve the thermoelectric properties further, nanostructured cuboidal pores are introduced into the bulk Ba1–xLaxTiO3 using F127 surfactant micelles for a chemical templating process, followed by spark plasma sintering. Interestingly, transmission electron microscopy images and X‐ray powder diffraction analysis confirms that our fabricated samples are cubic BaTiO3 perovskite phase with the nanostructured rectangular‐prism pores of >4 nm. Scanning electron microscopy images show that all the samples have similar grain boundaries and uniform La doping, which suggests that the large reduction in the lattice thermal conductivity in the F127‐treated samples arises primarily from the pore distribution, which introduces anisotropic phonon scattering within the unique nanoarchitecture. The sample with 20 at% La doping and nanopores also shows a thermopower that is doubled compared to the related sample without porosity. Together with the lattice thermal conductivity, enables a significant improvement in figure of merit, zT compared to the other samples.
- 15 March 2021
- Published by Wiley in Advanced Electronic Materials
- Vol. 7 (4) , 2001044
Significant Reduction in Thermal Conductivity and Improved Thermopower of Electron‐Doped Ba1–xLaxTiO3 with Nanostructured Rectangular Pores
Electron‐doped BaTiO3 is a less studied n‐type metal oxide thermoelectric material. In this work, the electrical conductivity of BaTiO3 samples has been improved by introducing La to yield an n‐type Ba1–xLaxTiO3 semiconducting material. Density functional theory calculations show that the optimal electron‐doping occurs at x = 0.2, and this is also confirmed experimentally. To improve the thermoelectric properties further, nanostructured cuboidal pores are introduced into the bulk Ba1–xLaxTiO3 using F127 surfactant micelles for a chemical templating process, followed by spark plasma sintering. Interestingly, transmission electron microscopy images and X‐ray powder diffraction analysis confirms that our fabricated samples are cubic BaTiO3 perovskite phase with the nanostructured rectangular‐prism pores of >4 nm. Scanning electron microscopy images show that all the samples have similar grain boundaries and uniform La doping, which suggests that the large reduction in the lattice thermal conductivity in the F127‐treated samples arises primarily from the pore distribution, which introduces anisotropic phonon scattering within the unique nanoarchitecture. The sample with 20 at% La doping and nanopores also shows a thermopower that is doubled compared to the related sample without porosity. Together with the lattice thermal conductivity, enables a significant improvement in figure of merit, zT compared to the other samples.
- Open Access
- 15 July 2020
- Published by Wiley in International Journal of Photoenergy
- Vol. 2020, 1-6
New Design of Solar Photovoltaic and Thermal Hybrid System for Performance Improvement of Solar Photovoltaic
Solar photovoltaic (PV) and solar thermal systems are most widely used renewable energy technologies. Theoretical study indicates that the energy conversion efficiency of solar photovoltaic gets reduced about 0.3% when its temperature increases by 1°C. In this regard, solar PV and thermal (PVT) hybrid systems could be a solution to draw extra heat from the solar PV panel to improve its performance by reducing its temperature. Here, we have designed a new type of heat exchanger for solar PV and thermal (PVT) hybrid systems and have studied the performance of the system. The PVT system has been investigated in comparison with an identical solar PV panel at outdoor condition at Dhaka, Bangladesh. The experiments show that the average improvement of open circuit voltage (Voc) is 0.97 V and the highest improvement of Voc is 1.3 V. In addition, the overall improvement of output power of solar PV panel is 2.5 W.
- 15 July 2020
- Published by Wiley in International Journal of Photoenergy
- Vol. 2020, 1-6
Open AccessNew Design of Solar Photovoltaic and Thermal Hybrid System for Performance Improvement of Solar Photovoltaic
Solar photovoltaic (PV) and solar thermal systems are most widely used renewable energy technologies. Theoretical study indicates that the energy conversion efficiency of solar photovoltaic gets reduced about 0.3% when its temperature increases by 1°C. In this regard, solar PV and thermal (PVT) hybrid systems could be a solution to draw extra heat from the solar PV panel to improve its performance by reducing its temperature. Here, we have designed a new type of heat exchanger for solar PV and thermal (PVT) hybrid systems and have studied the performance of the system. The PVT system has been investigated in comparison with an identical solar PV panel at outdoor condition at Dhaka, Bangladesh. The experiments show that the average improvement of open circuit voltage (Voc) is 0.97 V and the highest improvement of Voc is 1.3 V. In addition, the overall improvement of output power of solar PV panel is 2.5 W.
- 19 May 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (25) , 28057-28064
Significant Improvement in Electrical Conductivity and Figure of Merit of Nanoarchitectured Porous SrTiO3 by La Doping Optimization
SrTiO3 is a well-studied n-type metal-oxide based thermoelectric material. In this work, the First principle calculation of La doped SrTiO3 has been performed using the density functional theory (DFT). And high thermoelectric properties of bulk SrTiO3 material have been achieved by introducing nano-scale porosity and optimizing carrier concentration by La doping. The X-ray diffraction (XRD), atomic resolution scanning transmission electron microscopy (STEM) imaging and energy dispersive X-ray spectrometry (EDS) results show that La has been doped successfully into the lattice. The SEM images confirm that all the samples have nearly similar nano-scale porosities. The significant enhancement of electrical conductivity over the broad temperature range has been observed through optimization of La doping. Additionally, the samples have very low thermal conductivity, which is speculated due to the nano-scale porosity of the samples. Due to this dual mechanism of doping optimization and nano-scale porosity, there is a remarkable improvement in power factor, 1mW/m2K from 650 K to 800 K and figure of merit, zT of 0.26 at 850 K of the sample, 22 at% La doped SrTiO3.
- 19 May 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (25) , 28057-28064
Significant Improvement in Electrical Conductivity and Figure of Merit of Nanoarchitectured Porous SrTiO3 by La Doping Optimization
SrTiO3 is a well-studied n-type metal-oxide based thermoelectric material. In this work, the First principle calculation of La doped SrTiO3 has been performed using the density functional theory (DFT). And high thermoelectric properties of bulk SrTiO3 material have been achieved by introducing nano-scale porosity and optimizing carrier concentration by La doping. The X-ray diffraction (XRD), atomic resolution scanning transmission electron microscopy (STEM) imaging and energy dispersive X-ray spectrometry (EDS) results show that La has been doped successfully into the lattice. The SEM images confirm that all the samples have nearly similar nano-scale porosities. The significant enhancement of electrical conductivity over the broad temperature range has been observed through optimization of La doping. Additionally, the samples have very low thermal conductivity, which is speculated due to the nano-scale porosity of the samples. Due to this dual mechanism of doping optimization and nano-scale porosity, there is a remarkable improvement in power factor, 1mW/m2K from 650 K to 800 K and figure of merit, zT of 0.26 at 850 K of the sample, 22 at% La doped SrTiO3.
- Open Access
- 23 October 2019
- Published by The Royal Society in Royal Society Open Science
- Vol. 6 (10) , 190870
Enhancement of thermoelectric properties of La-doped SrTiO 3 bulk by introducing nanoscale porosity
Electron-doped SrTiO 3 is a well-known n -type thermoelectric material, although the figure of merit of SrTiO 3 is still inferior compared with p -type metal oxide-based thermoelectric materials due to its high lattice thermal conductivity. In this study, we have used a different amount of the non-ionic surfactant F127 during sample preparation to introduce nanoscale porosities into bulk samples of La-doped SrTiO 3 . It has been observed that the porosities introduced into the bulk sample significantly improve the Seebeck coefficient and reduce the thermal conductivity by the charge carrier and phonon scattering respectively. Therefore, there is an overall enhancement in the power factor (PF) followed by a dimensionless figure of merit ( zT ) over a wide scale of temperature. The sample 20 at% La-doped SrTiO 3 with 600 mg of F127 surfactant (SLTO 600F127) shows the maximum PF of 1.14 mW m −1 K −2 at 647 K which is 35% higher than the sample without porosity (SLTO 0F127), and the same sample (SLTO 600F127) shows the maximum value of z T is 0.32 at 968 K with an average enhancement of 62% in zT in comparison with the sample without porosity (SLTO 0F127).
- 23 October 2019
- Published by The Royal Society in Royal Society Open Science
- Vol. 6 (10) , 190870
Open AccessEnhancement of thermoelectric properties of La-doped SrTiO 3 bulk by introducing nanoscale porosity
Electron-doped SrTiO 3 is a well-known n -type thermoelectric material, although the figure of merit of SrTiO 3 is still inferior compared with p -type metal oxide-based thermoelectric materials due to its high lattice thermal conductivity. In this study, we have used a different amount of the non-ionic surfactant F127 during sample preparation to introduce nanoscale porosities into bulk samples of La-doped SrTiO 3 . It has been observed that the porosities introduced into the bulk sample significantly improve the Seebeck coefficient and reduce the thermal conductivity by the charge carrier and phonon scattering respectively. Therefore, there is an overall enhancement in the power factor (PF) followed by a dimensionless figure of merit ( zT ) over a wide scale of temperature. The sample 20 at% La-doped SrTiO 3 with 600 mg of F127 surfactant (SLTO 600F127) shows the maximum PF of 1.14 mW m −1 K −2 at 647 K which is 35% higher than the sample without porosity (SLTO 0F127), and the same sample (SLTO 600F127) shows the maximum value of z T is 0.32 at 968 K with an average enhancement of 62% in zT in comparison with the sample without porosity (SLTO 0F127).
- 1 December 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 406-412
Detection of heart condition by time and frequency based template
The phonocardiogram (PCG) is an easy and costless yet powerful tool to detect the heart condition. While the cardiovascular disease is an increasing global threat to humanity, there is a decrease in doctors' capability for diagnosing these diseases by auscultation. In this work, a neural network based automated system is proposed to aid early detection of these diseases. Two template-based feature representations are developed to effectively represent the characteristics of heart sound. These features, extracted from sound files of known cases, are then used to train a neural network. Our experimental results corroborate that the proposed method can efficiently detect the heart condition with good overall classification accuracy. In addition, a graphical user interface and a low cost device is developed which is user-friendly and can be used without much relevant knowledge.
- 1 December 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 406-412
Detection of heart condition by time and frequency based template
The phonocardiogram (PCG) is an easy and costless yet powerful tool to detect the heart condition. While the cardiovascular disease is an increasing global threat to humanity, there is a decrease in doctors' capability for diagnosing these diseases by auscultation. In this work, a neural network based automated system is proposed to aid early detection of these diseases. Two template-based feature representations are developed to effectively represent the characteristics of heart sound. These features, extracted from sound files of known cases, are then used to train a neural network. Our experimental results corroborate that the proposed method can efficiently detect the heart condition with good overall classification accuracy. In addition, a graphical user interface and a low cost device is developed which is user-friendly and can be used without much relevant knowledge.
- 1 September 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 9-13
Performance evaluation of solar panel and proposed new algorithm of solar tracking system
The output of a Solar Panel is highly dependent on solar radiation and other climatic conditions. Performance evaluation shows a solar panel can generate output power above 60% of its rated value for only six hours of a day from 9.00 am to 3.00 pm in Pondicherry, India. Based on the performance evaluation, we have proposed a new algorithm for timer based solar tracking system to harvest more sunlight by solar Panel.
- 1 September 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 9-13
Performance evaluation of solar panel and proposed new algorithm of solar tracking system
The output of a Solar Panel is highly dependent on solar radiation and other climatic conditions. Performance evaluation shows a solar panel can generate output power above 60% of its rated value for only six hours of a day from 9.00 am to 3.00 pm in Pondicherry, India. Based on the performance evaluation, we have proposed a new algorithm for timer based solar tracking system to harvest more sunlight by solar Panel.
- 1 May 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Optimizing anode microstructure of intermediate temperature Solid Oxide fuel cell based on Gadolinium doped Ceria
Solid Oxide fuel cell (SOFC) is one of the potential sources of alternative energy. Investigation has been carried out to improve the power density of the intermediate temperature SOFC by optimizing the composition of the anode materials. Nickel Oxide (NiO) and Gadolinium doped Ceria (GDC) have been used as anode materials. And graphite has been used as a pore former in the anode substrate. Samples have been characterized successfully at three different operating temperatures (600, 550 and 500° C). The maximum open circuit voltage (0.86V) and peak power density (48.62 mW/cm 2 ) have been obtained from the sample with composition of NiO, GDC and graphite in 25, 50 and 25 volume % respectively.
- 1 May 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Optimizing anode microstructure of intermediate temperature Solid Oxide fuel cell based on Gadolinium doped Ceria
Solid Oxide fuel cell (SOFC) is one of the potential sources of alternative energy. Investigation has been carried out to improve the power density of the intermediate temperature SOFC by optimizing the composition of the anode materials. Nickel Oxide (NiO) and Gadolinium doped Ceria (GDC) have been used as anode materials. And graphite has been used as a pore former in the anode substrate. Samples have been characterized successfully at three different operating temperatures (600, 550 and 500° C). The maximum open circuit voltage (0.86V) and peak power density (48.62 mW/cm 2 ) have been obtained from the sample with composition of NiO, GDC and graphite in 25, 50 and 25 volume % respectively.