Herman D. Haustein
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Herman D. Haustein has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Barak Kashi
2 shared publications- Alon Gany
Faculty of Aerospace Engineering, Technion—Israel Institute of Technology, Haifa 3200003, Israel
1 shared publication - Avishai Oved
School of Mechanical Engineering, Faculty of Engineering, Tel-Aviv University , Ramat-Aviv, Tel-Aviv, Israel
1 shared publication E. Elias
1 shared publication- Ezra Elias
Faculty of Mechanical Engineering, Technion–Israel Institute of Technology, Haifa 32000, Israel
1 shared publication - Lazarus Godson Asirvatham
Department of Mechanical Engineering, Karunya Institute of Technology and Sciences 8 , Coimbatore 641114
1 shared publication
Latest Publications
- Open Access
- 13 February 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 261
Unified analysis of flow and heat transfer distribution under evolved free-surface jets
- 13 February 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 261
Open AccessUnified analysis of flow and heat transfer distribution under evolved free-surface jets
- 17 December 2025
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 196
Impact boiling in real liquids under intense heating rates
- 17 December 2025
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 196
Impact boiling in real liquids under intense heating rates
- Open Access
- 28 March 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 245
Submerged jet's profile-specific heat transfer: Stagnation zone and beyond
- 28 March 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 245
Open AccessSubmerged jet's profile-specific heat transfer: Stagnation zone and beyond
- 1 March 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (3)
Analytical solution for the submerged free jet
Laminar submerged free jet theory still falls short in the near-nozzle region and transition to Schlichting's self-similar jet. The author's recent solution, based on mass conservation, is found lacking beyond the near-nozzle jet-core region. Instead, it is here constrained to conserve momentum, resulting in a locally linearized convection-diffusion equation, valid over jet width and up to self-similarity, when compared to simulations. This new solution leads to profile-specific values of virtual-origin correction to Schlichting's solution. Additionally, extensive jet characteristics are examined: (1) curvature core, (2) radial inflection location, (3) radial velocity, (4) vorticity field, (5) issuing mass, and (6) jet width. All are well predicted, and new insights are gained for a variety of issuing profiles: from uniform, through a non-monotonous profile and up to fully developed. The issuing mass of all non-uniform profiles undergoes an initial contraction proportional to the profile's level of development. Interestingly, the submerged jet contracts identically to the free-surface jet in the very near-nozzle region, before significant influence of their differing boundary conditions. Moreover, unless the issuing profile contains a radial inflection point, the inflection always occurs in the entrained fluid, just beyond the bounds of the issuing mass. It also follows an initial contraction and only later a widening toward the self-similar trend. Despite this contraction, the entrained fluid causes monotonous total jet-widening, at a rate inversely proportional to the level of development. Finally, this new solution correctly captures additional jet features, such as the local radial velocity and decay of the primary vorticity.
- 1 March 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (3)
Analytical solution for the submerged free jet
Laminar submerged free jet theory still falls short in the near-nozzle region and transition to Schlichting's self-similar jet. The author's recent solution, based on mass conservation, is found lacking beyond the near-nozzle jet-core region. Instead, it is here constrained to conserve momentum, resulting in a locally linearized convection-diffusion equation, valid over jet width and up to self-similarity, when compared to simulations. This new solution leads to profile-specific values of virtual-origin correction to Schlichting's solution. Additionally, extensive jet characteristics are examined: (1) curvature core, (2) radial inflection location, (3) radial velocity, (4) vorticity field, (5) issuing mass, and (6) jet width. All are well predicted, and new insights are gained for a variety of issuing profiles: from uniform, through a non-monotonous profile and up to fully developed. The issuing mass of all non-uniform profiles undergoes an initial contraction proportional to the profile's level of development. Interestingly, the submerged jet contracts identically to the free-surface jet in the very near-nozzle region, before significant influence of their differing boundary conditions. Moreover, unless the issuing profile contains a radial inflection point, the inflection always occurs in the entrained fluid, just beyond the bounds of the issuing mass. It also follows an initial contraction and only later a widening toward the self-similar trend. Despite this contraction, the entrained fluid causes monotonous total jet-widening, at a rate inversely proportional to the level of development. Finally, this new solution correctly captures additional jet features, such as the local radial velocity and decay of the primary vorticity.
- Open Access
- 14 September 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (9) , 710
Multiphase Marine Ramjet Using Liquefied Gas as a Source of Bubbles
An innovative variant of a multiphase marine ramjet is investigated analytically and experimentally. Pressure liquefied gas (LG) is injected, boiling under superheat conditions in the water stream within the propulsion unit, and serving as an on-board bubble source necessary for the ramjet operation. Experiments were conducted in a 10 m diameter tow pool at a speed range of 7–18 m/s (approximately 14–35 knots). For the laboratory concept demonstration and process characterization, two liquefied gases, butane and R134a (synthetic refrigerant gas), were employed. In practical applications, non-polluting LGs such as liquid air may be used. The results reveal the overall performance comparable to the operation with pressurized air, with some thrust advantage of the LG at high-speed tests, attributed to the volume increase of gas during phase change, in accordance with the thermodynamic power cycle analysis.
- 14 September 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (9) , 710
Open AccessMultiphase Marine Ramjet Using Liquefied Gas as a Source of Bubbles
An innovative variant of a multiphase marine ramjet is investigated analytically and experimentally. Pressure liquefied gas (LG) is injected, boiling under superheat conditions in the water stream within the propulsion unit, and serving as an on-board bubble source necessary for the ramjet operation. Experiments were conducted in a 10 m diameter tow pool at a speed range of 7–18 m/s (approximately 14–35 knots). For the laboratory concept demonstration and process characterization, two liquefied gases, butane and R134a (synthetic refrigerant gas), were employed. In practical applications, non-polluting LGs such as liquid air may be used. The results reveal the overall performance comparable to the operation with pressurized air, with some thrust advantage of the LG at high-speed tests, attributed to the volume increase of gas during phase change, in accordance with the thermodynamic power cycle analysis.
- 1 June 2019
- Published by AIP Publishing in Physics of Fluids
- Vol. 31 (6) , 063602
Distortion of pipe-flow development by boundary layer growth and unconstrained inlet conditions
This study extends the analysis of the canonical developing pipe-flow problem to realistic inlet conditions affecting emerging jets. A comparison of simulations to existing theory reveals adverse phenomena caused by the inlet: the velocity profile inversion and flow separation (vena contracta) at a sharp inlet. Beginning with the simple uniform inflow, the inversion is shown to persists at significantly higher Re (Re = 2000) than previously reported. It is found to be caused by the theory’s neglected radial velocity, resulting from the boundary layer’s displacement effect. Rescaling of the inlet axial coordinate is shown to collapse all centerline velocity curves above Re = 100, thus elucidating the known weak dependence of entrance-length on Re. The sharp-inlet separation bubble is found not to occur below Re ≅ 320 although this inlet profile overrides the boundary layer’s effect. Furthermore, the bubble’s downstream length increases rapidly with Re, whereas its upstream length grows gradually and proportionally to its thickness—here identified as its characteristic-scale. Beyond the bubble, the profile relaxes to a monotonic form—captured beyond x/(Re·R) = 0.005, if theory is modified using the bubble’s characteristic-scale. This scale also sets the threshold which differentiates between a sharp-inlet regime, accompanied by a separation bubble, and a rounded-inlet one without it. The latter regime relaxes more rapidly to the monotonic profile—captured already beyond x = 2R. Finally, the modified idealized theory is demonstrated as a useful design tool—explicitly relating nozzle length to characteristics of emerging free-surface and submerged jets.
- 1 June 2019
- Published by AIP Publishing in Physics of Fluids
- Vol. 31 (6) , 063602
Distortion of pipe-flow development by boundary layer growth and unconstrained inlet conditions
This study extends the analysis of the canonical developing pipe-flow problem to realistic inlet conditions affecting emerging jets. A comparison of simulations to existing theory reveals adverse phenomena caused by the inlet: the velocity profile inversion and flow separation (vena contracta) at a sharp inlet. Beginning with the simple uniform inflow, the inversion is shown to persists at significantly higher Re (Re = 2000) than previously reported. It is found to be caused by the theory’s neglected radial velocity, resulting from the boundary layer’s displacement effect. Rescaling of the inlet axial coordinate is shown to collapse all centerline velocity curves above Re = 100, thus elucidating the known weak dependence of entrance-length on Re. The sharp-inlet separation bubble is found not to occur below Re ≅ 320 although this inlet profile overrides the boundary layer’s effect. Furthermore, the bubble’s downstream length increases rapidly with Re, whereas its upstream length grows gradually and proportionally to its thickness—here identified as its characteristic-scale. Beyond the bubble, the profile relaxes to a monotonic form—captured beyond x/(Re·R) = 0.005, if theory is modified using the bubble’s characteristic-scale. This scale also sets the threshold which differentiates between a sharp-inlet regime, accompanied by a separation bubble, and a rounded-inlet one without it. The latter regime relaxes more rapidly to the monotonic profile—captured already beyond x = 2R. Finally, the modified idealized theory is demonstrated as a useful design tool—explicitly relating nozzle length to characteristics of emerging free-surface and submerged jets.
- 1 June 2019
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 479, 268-281
Effect of uniform/non-uniform magnetic field and jet impingement on the hydrodynamic and heat transfer performance of nanofluids
- 1 June 2019
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 479, 268-281
Effect of uniform/non-uniform magnetic field and jet impingement on the hydrodynamic and heat transfer performance of nanofluids