Pranay Prabhat
Research Subjects
Pranay Prabhat has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
James Myers
ARM Ltd., Cambridge CB1 9NJ, U.K.
12 shared publicationsAnand Savanth
Arm Research, Arm Ltd.,CambridgeU.K.,CB1 9NJ
6 shared publicationsRohan Gaddh
4 shared publications- Alex S. Weddell
University of Southampton
3 shared publications - Anand Savanth
Arm Research, Arm Ltd., Cambridge, U.K.
3 shared publications David Flynn
3 shared publications
Latest Publications
- Open Access
- 2 August 2022
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 12 (3) , 43
A Subthreshold Layout Strategy for Faster and Lower Energy Complex Digital Circuits
This work presents complex circuitry from subthreshold standard cell libraries created by geometric STI spacer patterning for bulk planar CMOS technology nodes. Performance/leakage granularity enhancement affords safer multi-Vt synthesis in aggressive voltage scaling schemes. Libraries are evaluated in silicon through implementation of 32-bit datapath 128-bit AES cores. Intra-die nominal temperature (20 °C) analysis reveals improvements of up to 8.65×/24% MEP-to-MEP in frequency and energy-per-cycle respectively, compared to a state-of-the-art subthreshold library. A negative temperature correlation with performance enhancement is demonstrated extending beyond the cell level and into more complex designs. MEP-to-MEP performance enhancement and energy-per-cycle reduction are demonstrated over a temperature range of 0 °C to 85 °C.
- 2 August 2022
- Published by MDPI AG in Journal of Low Power Electronics and Applications
- Vol. 12 (3) , 43
Open AccessA Subthreshold Layout Strategy for Faster and Lower Energy Complex Digital Circuits
This work presents complex circuitry from subthreshold standard cell libraries created by geometric STI spacer patterning for bulk planar CMOS technology nodes. Performance/leakage granularity enhancement affords safer multi-Vt synthesis in aggressive voltage scaling schemes. Libraries are evaluated in silicon through implementation of 32-bit datapath 128-bit AES cores. Intra-die nominal temperature (20 °C) analysis reveals improvements of up to 8.65×/24% MEP-to-MEP in frequency and energy-per-cycle respectively, compared to a state-of-the-art subthreshold library. A negative temperature correlation with performance enhancement is demonstrated extending beyond the cell level and into more complex designs. MEP-to-MEP performance enhancement and energy-per-cycle reduction are demonstrated over a temperature range of 0 °C to 85 °C.
- 19 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
- Vol. 42 (1) , 95-108
Pragmatic Memory-System Support for Intermittent Computing Using Emerging Nonvolatile Memory
Intermittent computing (IC) is a key enabler for the vision of a trillion Internet of Things devices. By harvesting energy from the environment, and leveraging non-volatile memory (NVM) to retain computational progress across power cycles, IC enables untethered and battery-free devices to perform computation whenever ambient energy is available. The backbone of state retention is NVM, and recent advances in energy-efficient NVM have the potential to expand the application domain of IC significantly. Utilizing emerging NVM at the level of bitcells, researchers have proposed non-volatile processors. However, these do not leverage hardware-software co-design, which can be used to overcome hardware limitations and to provide support for application-level constraints such as atomicity. In this paper, we propose MEMIC, a memory architecture tailored for IC devices with byte-addressable NVM. A core focus of MEMIC is to combine volatile-and non-volatile memory in such a way that the operations of IC are as efficient as possible, while also maximizing computational performance per joule. MEMIC uses volatile memory for energy efficiency, and nonvolatile memory for data retention. To avoid double-buffered checkpoints and costly roll-backs when code needs to be reexecuted, MEMIC is designed to track and minimize writes to non-volatile memory during failure-atomic sections. Our evaluation shows that MEMIC’s instruction cache reduces workload completion time under intermittent operation by 41-70% and its data cache provides a further reduction of 13-39%.
- 19 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
- Vol. 42 (1) , 95-108
Pragmatic Memory-System Support for Intermittent Computing Using Emerging Nonvolatile Memory
Intermittent computing (IC) is a key enabler for the vision of a trillion Internet of Things devices. By harvesting energy from the environment, and leveraging non-volatile memory (NVM) to retain computational progress across power cycles, IC enables untethered and battery-free devices to perform computation whenever ambient energy is available. The backbone of state retention is NVM, and recent advances in energy-efficient NVM have the potential to expand the application domain of IC significantly. Utilizing emerging NVM at the level of bitcells, researchers have proposed non-volatile processors. However, these do not leverage hardware-software co-design, which can be used to overcome hardware limitations and to provide support for application-level constraints such as atomicity. In this paper, we propose MEMIC, a memory architecture tailored for IC devices with byte-addressable NVM. A core focus of MEMIC is to combine volatile-and non-volatile memory in such a way that the operations of IC are as efficient as possible, while also maximizing computational performance per joule. MEMIC uses volatile memory for energy efficiency, and nonvolatile memory for data retention. To avoid double-buffered checkpoints and costly roll-backs when code needs to be reexecuted, MEMIC is designed to track and minimize writes to non-volatile memory during failure-atomic sections. Our evaluation shows that MEMIC’s instruction cache reduces workload completion time under intermittent operation by 41-70% and its data cache provides a further reduction of 13-39%.
- 22 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (2) , 601-611
A Supply Voltage Control Method for Performance Guaranteed Ultra-Low-Power Microcontroller
This article presents the control circuit of a power converter that regulates the computing speed of a digital circuit. The proposed circuit implements a digital delay regulation of a digital delay line (DDL) matched with the ring oscillator (RO) that clocks the digital subsystem. The converter regulates the supply voltage of the digital subsystem so that the propagation delay through the DDL matches a time reference. Consequently, the frequency of the RO tracks the DDL delay and the frequency keeps a controlled value over process, voltage, and temperature (PVT). A 65-nm CMOS prototype validates the proposed method. The prototype includes an Arm Cortex-M33 CPU and memories optimized for sub-threshold operation. With the proposed method, the computing performance of the CPU is guaranteed for running real-time application while minimizing the supply voltage margins.
- 22 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (2) , 601-611
A Supply Voltage Control Method for Performance Guaranteed Ultra-Low-Power Microcontroller
This article presents the control circuit of a power converter that regulates the computing speed of a digital circuit. The proposed circuit implements a digital delay regulation of a digital delay line (DDL) matched with the ring oscillator (RO) that clocks the digital subsystem. The converter regulates the supply voltage of the digital subsystem so that the propagation delay through the DDL matches a time reference. Consequently, the frequency of the RO tracks the DDL delay and the frequency keeps a controlled value over process, voltage, and temperature (PVT). A 65-nm CMOS prototype validates the proposed method. The prototype includes an Arm Cortex-M33 CPU and memories optimized for sub-threshold operation. With the proposed method, the computing performance of the CPU is guaranteed for running real-time application while minimizing the supply voltage margins.
- 21 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 2 (9) , 175-178
A 0.98-nW/kHz 33-kHz Fully Integrated Subthreshold-Region Operation RC Oscillator With Forward-Body-Biasing
The lower bound on the power expended by an RC relaxation oscillator is decided by the RC network. This can be minimized by reducing the oscillation swing and increasing R. In the former technique, tighter comparator constraints limit power benefits while the latter technique increases resistor thermal noise bounding long-term jitter. To this end, this letter presents a fully integrated RC oscillator with core voltage aggressively scaled to subthreshold levels. A self-clocked switched-capacitor network is used to minimize voltage drop-out power loss. Full forward-body-biasing technique helps reduce device on-resistance. Additionally, temperature coefficient compensation for time constant is accomplished by poly resistors and a V TH -tracking reference scheme which avoids the use of diffusion resistors. This design is silicon-proven on 65-nm CMOS (0.0356-mm 2 area). The implementation has a 33-kHz clock with 32.2 nW at 1.2 V. Line sensitivity is within +0.7/−0.6% per volt across 16 samples for 1 to 1.5 V. Temperature sensitivity was measured to be 56 ppm/°C from 0 °C to 85 °C and measured Allan deviation < 100 ppm for averaging interval of $\tau = 400$ s and < 40 ppm for $\tau = 3000$ s.
- 21 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 2 (9) , 175-178
A 0.98-nW/kHz 33-kHz Fully Integrated Subthreshold-Region Operation RC Oscillator With Forward-Body-Biasing
The lower bound on the power expended by an RC relaxation oscillator is decided by the RC network. This can be minimized by reducing the oscillation swing and increasing R. In the former technique, tighter comparator constraints limit power benefits while the latter technique increases resistor thermal noise bounding long-term jitter. To this end, this letter presents a fully integrated RC oscillator with core voltage aggressively scaled to subthreshold levels. A self-clocked switched-capacitor network is used to minimize voltage drop-out power loss. Full forward-body-biasing technique helps reduce device on-resistance. Additionally, temperature coefficient compensation for time constant is accomplished by poly resistors and a V TH -tracking reference scheme which avoids the use of diffusion resistors. This design is silicon-proven on 65-nm CMOS (0.0356-mm 2 area). The implementation has a 33-kHz clock with 32.2 nW at 1.2 V. Line sensitivity is within +0.7/−0.6% per volt across 16 samples for 1 to 1.5 V. Temperature sensitivity was measured to be 56 ppm/°C from 0 °C to 85 °C and measured Allan deviation < 100 ppm for averaging interval of $\tau = 400$ s and < 40 ppm for $\tau = 3000$ s.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A 0.98-nW/kHz 33-kHz Fully Integrated Subthreshold-Region Operation RC Oscillator With Forward-Body-Biasing
The lower bound on the power expended by an RC relaxation oscillator is decided by the RC network. This can be minimized by reducing the oscillation swing and increasing R. In the former technique, tighter comparator constraints limit power benefits while the latter technique increases resistor thermal noise bounding long-term jitter. To this end, this letter presents a fully integrated RC oscillator with core voltage aggressively scaled to subthreshold levels. A self-clocked switched-capacitor network is used to minimize voltage drop-out power loss. Full forward-body-biasing technique helps reduce device on-resistance. Additionally, temperature coefficient compensation for time constant is accomplished by poly resistors and a V TH -tracking reference scheme which avoids the use of diffusion resistors. This design is silicon-proven on 65-nm CMOS (0.0356-mm2 area). The implementation has a 33-kHz clock with 32.2 nW at 1.2 V. Line sensitivity is within +0.7/−0.6% per volt across 16 samples for 1 to 1.5 V. Temperature sensitivity was measured to be 56 ppm/°C from 0 °C to 85 °C and measured Allan deviation <100 ppm for averaging interval of τ = 400 s and <40 ppm for τ = 3000 s.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A 0.98-nW/kHz 33-kHz Fully Integrated Subthreshold-Region Operation RC Oscillator With Forward-Body-Biasing
The lower bound on the power expended by an RC relaxation oscillator is decided by the RC network. This can be minimized by reducing the oscillation swing and increasing R. In the former technique, tighter comparator constraints limit power benefits while the latter technique increases resistor thermal noise bounding long-term jitter. To this end, this letter presents a fully integrated RC oscillator with core voltage aggressively scaled to subthreshold levels. A self-clocked switched-capacitor network is used to minimize voltage drop-out power loss. Full forward-body-biasing technique helps reduce device on-resistance. Additionally, temperature coefficient compensation for time constant is accomplished by poly resistors and a V TH -tracking reference scheme which avoids the use of diffusion resistors. This design is silicon-proven on 65-nm CMOS (0.0356-mm2 area). The implementation has a 33-kHz clock with 32.2 nW at 1.2 V. Line sensitivity is within +0.7/−0.6% per volt across 16 samples for 1 to 1.5 V. Temperature sensitivity was measured to be 56 ppm/°C from 0 °C to 85 °C and measured Allan deviation <100 ppm for averaging interval of τ = 400 s and <40 ppm for τ = 3000 s.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
A 65nm switched source line sub-threshold ROM using data encoding, with 0.3V Vmin and 47fJ/b access energy
Battery-operated sensing systems have very low activity rates and power down most blocks during inactive periods to save power. During active periods, these energy-constrained systems typically operate at near or sub-threshold voltage for maintaining energy efficiency. Therefore, these ultra-low energy systems require a read-only, non-volatile code memory that can be accessed at sub-threshold voltage. ROM is the most energy efficient read-only non-volatile memory. A conventional compiler ROM cannot work reliably in near threshold regions of operation due to lack of read margin. As a result, for energy constrained IoT systems, the ROM design needs to support reliable read at low operating voltages, and a speed degradation at low voltages which is at par with logic circuits, to avoid the ROM from limiting the system performance. This paper proposes a sub-threshold ROM that addresses both reliability and performance issues by 1) Using a switched source-line (SSL) to nullify Ioff and improve read margin, 2) Compensating performance degradation caused by SSL using a novel data encoding scheme and by using unused ‘0’ bit-cell transistors to provide local pull-down paths, 3) Tackle variation-based performance degradation by optimizing bit-cell sizing for sub-threshold, and 4) Providing a fine-grained threshold voltage adjustment technique for trading off performance improvement with leakage degradation by using a novel INverse Width Effect (INWE) bit-cell layout. The proposed SSL sub-threshold ROM is fabricated in 65nm technology, with an 8kB capacity, and a V min of 0.3V. At 0.4V, it has a read speed of 1.1MHz and an access energy of 47fJ/bit.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
A 65nm switched source line sub-threshold ROM using data encoding, with 0.3V Vmin and 47fJ/b access energy
Battery-operated sensing systems have very low activity rates and power down most blocks during inactive periods to save power. During active periods, these energy-constrained systems typically operate at near or sub-threshold voltage for maintaining energy efficiency. Therefore, these ultra-low energy systems require a read-only, non-volatile code memory that can be accessed at sub-threshold voltage. ROM is the most energy efficient read-only non-volatile memory. A conventional compiler ROM cannot work reliably in near threshold regions of operation due to lack of read margin. As a result, for energy constrained IoT systems, the ROM design needs to support reliable read at low operating voltages, and a speed degradation at low voltages which is at par with logic circuits, to avoid the ROM from limiting the system performance. This paper proposes a sub-threshold ROM that addresses both reliability and performance issues by 1) Using a switched source-line (SSL) to nullify Ioff and improve read margin, 2) Compensating performance degradation caused by SSL using a novel data encoding scheme and by using unused ‘0’ bit-cell transistors to provide local pull-down paths, 3) Tackle variation-based performance degradation by optimizing bit-cell sizing for sub-threshold, and 4) Providing a fine-grained threshold voltage adjustment technique for trading off performance improvement with leakage degradation by using a novel INverse Width Effect (INWE) bit-cell layout. The proposed SSL sub-threshold ROM is fabricated in 65nm technology, with an 8kB capacity, and a V min of 0.3V. At 0.4V, it has a read speed of 1.1MHz and an access energy of 47fJ/bit.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 183-186
A bulk 65nm Cortex-M0+ SoC with All-Digital Forward Body Bias for 4.3X Subthreshold Speedup
IoT devices demand ultra-low power operation while still achieving the performance demanded by application constraints. Dynamic forward body biasing can help to achieve this by providing a speed-up during active operation without incurring a leakage penalty' during standby periods. While body biasing has been fully explored in FD-SoI technology, bulk CMOS can also benefit from efficient forward body biasing. At subthreshold voltage levels, the Low Voltage Swapped Body (LVSB) technique, in which n-well and p-well are driven to VSS and VDD respectively, helps to realize a significant speedup without incurring analog bias generation overheads. This work presents key advances to leverage LVSB, proven on a bulk 65nm subthreshold Arm Cortex-M0+ system. The system achieves a 4.3X speedup on the ULPBench benchmark at a cost of only 11% average power and 10.4% area, while showing that LVSB can be usefully applied up to 0.50V.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 183-186
A bulk 65nm Cortex-M0+ SoC with All-Digital Forward Body Bias for 4.3X Subthreshold Speedup
IoT devices demand ultra-low power operation while still achieving the performance demanded by application constraints. Dynamic forward body biasing can help to achieve this by providing a speed-up during active operation without incurring a leakage penalty' during standby periods. While body biasing has been fully explored in FD-SoI technology, bulk CMOS can also benefit from efficient forward body biasing. At subthreshold voltage levels, the Low Voltage Swapped Body (LVSB) technique, in which n-well and p-well are driven to VSS and VDD respectively, helps to realize a significant speedup without incurring analog bias generation overheads. This work presents key advances to leverage LVSB, proven on a bulk 65nm subthreshold Arm Cortex-M0+ system. The system achieves a 4.3X speedup on the ULPBench benchmark at a cost of only 11% average power and 10.4% area, while showing that LVSB can be usefully applied up to 0.50V.
- 26 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (2) , 550-559
Ultra-Low Power 18-Transistor Fully Static Contention-Free Single-Phase Clocked Flip-Flop in 65-nm CMOS
Flip-flops (FFs) are essential building blocks of sequential digital circuits but typically occupy a substantial proportion of chip area and consume significant amounts of power. This paper proposes 18-transistor single-phase clocked (18TSPC), a new topology of fully static contention-free single-phase clocked (SPC) FF with only 18 transistors, the lowest number reported for this type. Implemented in 65-nm CMOS, it achieves 20% cell area reduction compared to the conventional transmission gate FF (TGFF). Simulation results show the proposed 18TSPC is two times more efficient than TGFF in the energy-delay space. To demonstrate EDA compatibility and circuit/system-level benefits, a shift register and an AES-128 encryption engine have been implemented. Chip experimental measurements at 0.6 V, 25 °C show that, compared to TGFF, the proposed 18TSPC achieves reductions of 68% and 73% in overall and clock dynamic power, respectively, and 27% lower leakage.
- 26 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (2) , 550-559
Ultra-Low Power 18-Transistor Fully Static Contention-Free Single-Phase Clocked Flip-Flop in 65-nm CMOS
Flip-flops (FFs) are essential building blocks of sequential digital circuits but typically occupy a substantial proportion of chip area and consume significant amounts of power. This paper proposes 18-transistor single-phase clocked (18TSPC), a new topology of fully static contention-free single-phase clocked (SPC) FF with only 18 transistors, the lowest number reported for this type. Implemented in 65-nm CMOS, it achieves 20% cell area reduction compared to the conventional transmission gate FF (TGFF). Simulation results show the proposed 18TSPC is two times more efficient than TGFF in the energy-delay space. To demonstrate EDA compatibility and circuit/system-level benefits, a shift register and an AES-128 encryption engine have been implemented. Chip experimental measurements at 0.6 V, 25 °C show that, compared to TGFF, the proposed 18TSPC achieves reductions of 68% and 73% in overall and clock dynamic power, respectively, and 27% lower leakage.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Evaluation and analysis of single-phase clock flip-flops for NTV applications
Performance slack in IoT applications is routinely exploited in sensor nodes to minimize power by aggressive voltage scaling. However, scaling voltage to sub-threshold levels causes severe degradation in performance and is prone to On Chip Variation (OCV). In contrast, Near Threshold Voltage (NTV) operation offers a good balance between performance loss, OCV and energy reduction and is promising for industry adoption. Unlike sub-threshold operation, where leakage power dominates, NTV designs benefit from dynamic power saving techniques, such as Single-Phase Clocked Flip-Flops (SPC FFs), which eliminate internal clock buffers. In this context, this work reviews prominent types of state-of-the-art SPC FFs and analyses their suitability for NTV operation. Five SPC FFs are reviewed and based on a preliminary analysis, two designs, which meet all NTV circuit design requirements are further investigated. These SPC FFs are designed for NTV operation in TSMC 65LP and compared against the classic transmission gate FF (TGFF). Celllevel design issues and variation are explored in the context of a 5000 gate AES encryption macro. Key design issues are identified, which erode the claimed benefits of SPC FFs when implemented as part of a larger design. We conclude that aggressive reduction in FF clock loading offers benefits but can lead to functional failures when OCV is considered, especially at NTV. Given the theoretical benefits of SPC FFs for enabling IoT, the need for further work on SPC FF designs is highlighted.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Evaluation and analysis of single-phase clock flip-flops for NTV applications
Performance slack in IoT applications is routinely exploited in sensor nodes to minimize power by aggressive voltage scaling. However, scaling voltage to sub-threshold levels causes severe degradation in performance and is prone to On Chip Variation (OCV). In contrast, Near Threshold Voltage (NTV) operation offers a good balance between performance loss, OCV and energy reduction and is promising for industry adoption. Unlike sub-threshold operation, where leakage power dominates, NTV designs benefit from dynamic power saving techniques, such as Single-Phase Clocked Flip-Flops (SPC FFs), which eliminate internal clock buffers. In this context, this work reviews prominent types of state-of-the-art SPC FFs and analyses their suitability for NTV operation. Five SPC FFs are reviewed and based on a preliminary analysis, two designs, which meet all NTV circuit design requirements are further investigated. These SPC FFs are designed for NTV operation in TSMC 65LP and compared against the classic transmission gate FF (TGFF). Celllevel design issues and variation are explored in the context of a 5000 gate AES encryption macro. Key design issues are identified, which erode the claimed benefits of SPC FFs when implemented as part of a larger design. We conclude that aggressive reduction in FF clock loading offers benefits but can lead to functional failures when OCV is considered, especially at NTV. Given the theoretical benefits of SPC FFs for enabling IoT, the need for further work on SPC FF designs is highlighted.
- 1 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 19-24
Unconventional Layout Techniques for a High Performance, Low Variability Subthreshold Standard Cell Library
A novel subthreshold sizing strategy utilizing the Inverse Narrow Width Effect is demonstrated that has the largest range of propagation delays within the same cell footprint and lowest variability of any subthreshold sizing strategy thus far proposed. Simulation results and ring oscillators implemented in a commercial 65nm low power process confirm a propagation delay improvement of up to 1.95X over the standard superthreshold sizing strategy at 300mV and below. 32 bit multipliers are then synthesized and static timing analysis performed at several subthreshold voltage corners to illustrate applicability to real designs in conventional EDA design flows.
- 1 July 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 19-24
Unconventional Layout Techniques for a High Performance, Low Variability Subthreshold Standard Cell Library
A novel subthreshold sizing strategy utilizing the Inverse Narrow Width Effect is demonstrated that has the largest range of propagation delays within the same cell footprint and lowest variability of any subthreshold sizing strategy thus far proposed. Simulation results and ring oscillators implemented in a commercial 65nm low power process confirm a propagation delay improvement of up to 1.95X over the standard superthreshold sizing strategy at 300mV and below. 32 bit multipliers are then synthesized and static timing analysis performed at several subthreshold voltage corners to illustrate applicability to real designs in conventional EDA design flows.