Huiyang Deng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Huiyang Deng has a total of 95 co-authors. Here are the top co-authors by number of shared publications:
James S. Harris
16 shared publicationsRobert L. Byer
11 shared publicationsYusi Chen
Stanford Univ, Dept Elect Engn, Stanford, CA 94305 USA
7 shared publicationsJieyang Jia
Stanford Univ, Dept Elect Engn, Stanford, CA 94305 USA
6 shared publicationsAndrew Ceballos
Department of Electrical Engineering Stanford University Stanford CA 94305 USA
5 shared publicationsKenneth J. Leedle
Department of Electrical Engineering Stanford University Stanford CA 94305 USA
5 shared publications
Latest Publications
- 10 April 2020
- Published by Optica Publishing Group in Optics Express
- Vol. 28 (8) , 12475-12486
Low-loss GaOx-core/SiO2-cladding planar waveguides on Si substrate
The unique properties of gallium oxide (GaOx) have drawn increasing interest as a material suitable for high-power electronic and optical applications. Herein, we report the demonstration of low-loss GaOx-core/SiO2-cladding waveguides on Si substrate. We present the fabrication process and annealing treatments of the waveguide devices, and we characterize the corresponding effects on optical transmission for 3 common wavelengths: 633 nm, 1064 nm, and 1550 nm. The best propagation loss achieved for these wavelengths is measured to be − 0.4 ± 0.1 dB/cm , − 0.3 ± 0.2 dB/cm , and − 2.4 ± 0.5 dB/cm , respectively. We discuss the major waveguide loss mechanisms, followed by results of pump and probe experiments using visible/IR wavelengths for waveguides treated under various post-fabrication annealing conditions. We also show nonlinear measurements for a 250 fs laser beam to offer additional insights into the loss mechanisms, which are consistent with the linear optical transmission performances. High waveguide laser-induced damage threshold (LIDT) of > 2.5 J/cm 2 is measured at this pulse width, making GaOx a potential candidate for high-power integrated photonic devices.
- 10 April 2020
- Published by Optica Publishing Group in Optics Express
- Vol. 28 (8) , 12475-12486
Low-loss GaOx-core/SiO2-cladding planar waveguides on Si substrate
The unique properties of gallium oxide (GaOx) have drawn increasing interest as a material suitable for high-power electronic and optical applications. Herein, we report the demonstration of low-loss GaOx-core/SiO2-cladding waveguides on Si substrate. We present the fabrication process and annealing treatments of the waveguide devices, and we characterize the corresponding effects on optical transmission for 3 common wavelengths: 633 nm, 1064 nm, and 1550 nm. The best propagation loss achieved for these wavelengths is measured to be − 0.4 ± 0.1 dB/cm , − 0.3 ± 0.2 dB/cm , and − 2.4 ± 0.5 dB/cm , respectively. We discuss the major waveguide loss mechanisms, followed by results of pump and probe experiments using visible/IR wavelengths for waveguides treated under various post-fabrication annealing conditions. We also show nonlinear measurements for a 250 fs laser beam to offer additional insights into the loss mechanisms, which are consistent with the linear optical transmission performances. High waveguide laser-induced damage threshold (LIDT) of > 2.5 J/cm 2 is measured at this pulse width, making GaOx a potential candidate for high-power integrated photonic devices.
- Open Access
- 20 January 2020
- Published by Wiley in Advanced Optical Materials
- Vol. 8 (7)
Gallium Oxide for High‐Power Optical Applications
Gallium oxide (Ga2O3) is an emerging wide‐bandgap transparent conductive oxide (TCO) with potential applications for high‐power optical systems. Herein, Ga2O3 fabricated nanostructures are described, which demonstrate high‐power laser induced damage threshold (LIDT). Furthermore, the demonstration of an electron accelerator based on Ga2O3 gratings is reported. These unique Ga2O3 nanostructures provide acceleration gradients exceeding those possible with conventional RF accelerators due to the high breakdown threshold of Ga2O3. In addition, the laser damage threshold and acceleration performance of a Ga2O3‐based dielectric laser accelerator (DLA) are compared with those of a DLA based on sapphire, a material known for its high breakdown strength. Finally, the potential of Ga2O3 thin‐film coatings as field reduction layers for Si nanostructures is shown; they potentially improve the effective LIDT and performance of Si‐based DLAs and other high‐power optical structures. These results could provide a foundation for new high‐power optical applications with Ga2O3.
- 20 January 2020
- Published by Wiley in Advanced Optical Materials
- Vol. 8 (7)
Open AccessGallium Oxide for High‐Power Optical Applications
Gallium oxide (Ga2O3) is an emerging wide‐bandgap transparent conductive oxide (TCO) with potential applications for high‐power optical systems. Herein, Ga2O3 fabricated nanostructures are described, which demonstrate high‐power laser induced damage threshold (LIDT). Furthermore, the demonstration of an electron accelerator based on Ga2O3 gratings is reported. These unique Ga2O3 nanostructures provide acceleration gradients exceeding those possible with conventional RF accelerators due to the high breakdown threshold of Ga2O3. In addition, the laser damage threshold and acceleration performance of a Ga2O3‐based dielectric laser accelerator (DLA) are compared with those of a DLA based on sapphire, a material known for its high breakdown strength. Finally, the potential of Ga2O3 thin‐film coatings as field reduction layers for Si nanostructures is shown; they potentially improve the effective LIDT and performance of Si‐based DLAs and other high‐power optical structures. These results could provide a foundation for new high‐power optical applications with Ga2O3.
- Open Access
- 15 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (6) , 1-7
Titanium Dioxide Hole-Blocking Layer in Ultra-Thin-Film Crystalline Silicon Solar Cells
- 15 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 11 (6) , 1-7
Open AccessTitanium Dioxide Hole-Blocking Layer in Ultra-Thin-Film Crystalline Silicon Solar Cells
- 1 January 2019
- Published by Optica Publishing Group
- p. SF2H.7
Design of a tapered slot waveguide dielectric laser accelerator for sub-relativistic electrons
We design and analyze a tapered slot waveguide structure for sub-relativistic electron acceleration. The tapering scheme can be designed, through the eikonal approximation, to achieve phase synchronization with the accelerated electrons.
- 1 January 2019
- Published by Optica Publishing Group
- p. SF2H.7
Design of a tapered slot waveguide dielectric laser accelerator for sub-relativistic electrons
We design and analyze a tapered slot waveguide structure for sub-relativistic electron acceleration. The tapering scheme can be designed, through the eikonal approximation, to achieve phase synchronization with the accelerated electrons.
- 21 August 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (18) , 22801-22815
Design of a tapered slot waveguide dielectric laser accelerator for sub-relativistic electrons
We propose a dielectric laser accelerator design based on a tapered slot waveguide structure for sub-relativistic electron acceleration. This tapering scheme allows for straightforward tuning of the phase velocity of the accelerating field along the propagation direction, which is necessary for maintaining synchronization with electrons as their velocities increase. Furthermore, the non-resonant nature of this design allows for better tolerance to experimental errors. We also introduce a method to design this continuously tapered structure based on the eikonal approximation, and give a working example based on realistic experimental parameters.
- 21 August 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (18) , 22801-22815
Design of a tapered slot waveguide dielectric laser accelerator for sub-relativistic electrons
We propose a dielectric laser accelerator design based on a tapered slot waveguide structure for sub-relativistic electron acceleration. This tapering scheme allows for straightforward tuning of the phase velocity of the accelerating field along the propagation direction, which is necessary for maintaining synchronization with electrons as their velocities increase. Furthermore, the non-resonant nature of this design allows for better tolerance to experimental errors. We also introduce a method to design this continuously tapered structure based on the eikonal approximation, and give a working example based on realistic experimental parameters.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2180-2182
Investigation of Nickel Oxide as Carrier-selective Interlayer for Silicon Solar Cell Contacts
Thin film crystalline silicon (c-Si) solar cells have been a potential candidate to reduce the capital expenditure associated with traditional silicon photovoltaic market. This paper presents the sputtered NiOx to be a potential candidate as hole-selective layer for c-Si solar cell contacts. NiOx has a very small valence band offset (VBO) (~0.1 eV) and a large conduction band offset (CBO) with Si (~2 eV), which makes it a promising candidate for hole-selective interlayer materials to reduce the contact recombination. In this paper, the effect of annealing condition on the NiOx/Si interface quality is first evaluated by Hall resistivity measurement. Also, the transport of both majority and minority carriers due to NiOx/Si band alignment is investigated by transmission line measurement. Results in this paper show that the sputtered NiOx can be an effective interlayer material for thin film c-Si solar cell contacts.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2180-2182
Investigation of Nickel Oxide as Carrier-selective Interlayer for Silicon Solar Cell Contacts
Thin film crystalline silicon (c-Si) solar cells have been a potential candidate to reduce the capital expenditure associated with traditional silicon photovoltaic market. This paper presents the sputtered NiOx to be a potential candidate as hole-selective layer for c-Si solar cell contacts. NiOx has a very small valence band offset (VBO) (~0.1 eV) and a large conduction band offset (CBO) with Si (~2 eV), which makes it a promising candidate for hole-selective interlayer materials to reduce the contact recombination. In this paper, the effect of annealing condition on the NiOx/Si interface quality is first evaluated by Hall resistivity measurement. Also, the transport of both majority and minority carriers due to NiOx/Si band alignment is investigated by transmission line measurement. Results in this paper show that the sputtered NiOx can be an effective interlayer material for thin film c-Si solar cell contacts.
- Open Access
- 25 May 2018
- Published by Optica Publishing Group in Optica
- Vol. 5 (6) , 687-690
Elements of a dielectric laser accelerator
We experimentally demonstrate several physical concepts necessary for the future development of dielectric laser accelerators—photonic elements that utilize the inelastic interaction between electrons and the optical near fields of laser-illuminated periodic nanostructures. To build a fully photonic accelerator, concatenation of elements, large energy gains, and beam steering elements are required. Staged acceleration is shown using two spatio-temporally separated interaction regions. Further, a chirped silicon grating is used to overcome the velocity dephasing of subrelativistic electrons with respect to its optical near fields, and last, a parabolic grating geometry serves for focusing of the electron beam.
- 25 May 2018
- Published by Optica Publishing Group in Optica
- Vol. 5 (6) , 687-690
Open AccessElements of a dielectric laser accelerator
We experimentally demonstrate several physical concepts necessary for the future development of dielectric laser accelerators—photonic elements that utilize the inelastic interaction between electrons and the optical near fields of laser-illuminated periodic nanostructures. To build a fully photonic accelerator, concatenation of elements, large energy gains, and beam steering elements are required. Staged acceleration is shown using two spatio-temporally separated interaction regions. Further, a chirped silicon grating is used to overcome the velocity dephasing of subrelativistic electrons with respect to its optical near fields, and last, a parabolic grating geometry serves for focusing of the electron beam.
- 14 May 2018
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 9 (5) , 054017
On-Chip Laser-Power Delivery System for Dielectric Laser Accelerators
We propose an on-chip optical-power delivery system for dielectric laser accelerators based on a fractal “tree-network” dielectric waveguide geometry. This system replaces experimentally demanding free-space manipulations of the driving laser beam with chip-integrated techniques based on precise nanofabrication, enabling access to orders-of-magnitude increases in the interaction length and total energy gain for these miniature accelerators. Based on computational modeling, in the relativistic regime, our laser delivery system is estimated to provide 21 keV of energy gain over an acceleration length of with a single laser input, corresponding to a 108-MV/m acceleration gradient. The system may achieve 1 MeV of energy gain over a distance of less than 1 cm by sequentially illuminating 49 identical structures. These findings are verified by detailed numerical simulation and modeling of the subcomponents, and we provide a discussion of the main constraints, challenges, and relevant parameters with regard to on-chip laser coupling for dielectric laser accelerators.- 14 May 2018
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 9 (5) , 054017
On-Chip Laser-Power Delivery System for Dielectric Laser Accelerators
We propose an on-chip optical-power delivery system for dielectric laser accelerators based on a fractal “tree-network” dielectric waveguide geometry. This system replaces experimentally demanding free-space manipulations of the driving laser beam with chip-integrated techniques based on precise nanofabrication, enabling access to orders-of-magnitude increases in the interaction length and total energy gain for these miniature accelerators. Based on computational modeling, in the relativistic regime, our laser delivery system is estimated to provide 21 keV of energy gain over an acceleration length of with a single laser input, corresponding to a 108-MV/m acceleration gradient. The system may achieve 1 MeV of energy gain over a distance of less than 1 cm by sequentially illuminating 49 identical structures. These findings are verified by detailed numerical simulation and modeling of the subcomponents, and we provide a discussion of the main constraints, challenges, and relevant parameters with regard to on-chip laser coupling for dielectric laser accelerators.- 27 April 2018
- Published by Optica Publishing Group in Optics Letters
- Vol. 43 (9) , 2181-2184
Phase-dependent laser acceleration of electrons with symmetrically driven silicon dual pillar gratings
We present the demonstration of phase-dependent laser acceleration and deflection of electrons using a symmetrically driven silicon dual pillar grating structure. We show that exciting an evanescent inverse Smith–Purcell mode on each side of a dual pillar grating can produce hyperbolic cosine acceleration and hyperbolic sine deflection modes, depending on the relative excitation phase of each side. Our devices accelerate sub-relativistic 99.0 keV kinetic energy electrons by 3.0 keV over a 15 μm distance with accelerating gradients of 200 MeV/m with 40 nJ, 300 fs, 1940 nm pulses from an optical parametric amplifier. These results represent a significant step towards making practical dielectric laser accelerators for ultrafast, medical, and high-energy applications.
- 27 April 2018
- Published by Optica Publishing Group in Optics Letters
- Vol. 43 (9) , 2181-2184
Phase-dependent laser acceleration of electrons with symmetrically driven silicon dual pillar gratings
We present the demonstration of phase-dependent laser acceleration and deflection of electrons using a symmetrically driven silicon dual pillar grating structure. We show that exciting an evanescent inverse Smith–Purcell mode on each side of a dual pillar grating can produce hyperbolic cosine acceleration and hyperbolic sine deflection modes, depending on the relative excitation phase of each side. Our devices accelerate sub-relativistic 99.0 keV kinetic energy electrons by 3.0 keV over a 15 μm distance with accelerating gradients of 200 MeV/m with 40 nJ, 300 fs, 1940 nm pulses from an optical parametric amplifier. These results represent a significant step towards making practical dielectric laser accelerators for ultrafast, medical, and high-energy applications.
- 1 January 2018
- Published by Optica Publishing Group
- p. FM3M.7
Phase-Dependent Dielectric Laser Acceleration of 99keV Electrons with Symmetrically Driven Silicon Dual Pillar Gratings
We present phase-dependent laser acceleration and deflection of electrons using a symmetrically driven silicon dual pillar grating. We demonstrate cosh accelerator modes and sinh deflecting modes at gradients of 200 MeV/m over 15 μm distance.
- 1 January 2018
- Published by Optica Publishing Group
- p. FM3M.7
Phase-Dependent Dielectric Laser Acceleration of 99keV Electrons with Symmetrically Driven Silicon Dual Pillar Gratings
We present phase-dependent laser acceleration and deflection of electrons using a symmetrically driven silicon dual pillar grating. We demonstrate cosh accelerator modes and sinh deflecting modes at gradients of 200 MeV/m over 15 μm distance.