Xiaolei Zhu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xiaolei Zhu has a total of 114 co-authors. Here are the top co-authors by number of shared publications:
Weibiao Chen
Key Laboratory of Space Laser Communication and Detection Technology, Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, Shanghai 201800, China
17 shared publicationsTingting Lu
Key Laboratory of Space Laser Communication and Detection Technology, Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, Shanghai 201800, People’s Republic of China
7 shared publicationsHuaguo Zang
6 shared publicationsShiguang Li
6 shared publicationsJunxuan Zhang
Laboratory of Space Laser Engineering, Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, Shanghai
5 shared publicationsDennis Lo
Physics Department, The Chinese University of Hong Kong, Shatin, New Territories, Hong Kong, China
4 shared publications
Latest Publications
- 28 April 2023
- Published by IOP Publishing in Laser Physics Letters
- Vol. 20 (5) , 055001
486 nm pulsed Nd:YLF laser with intracavity sum-frequency mixing
An intracavity sum-frequency pulsed laser emitting at 486 nm was demonstrated in a combined cavity for two electro-optically Q-switched Nd:YLF fundamental lasers emitting at 908 nm and 1047 nm respectively. Pumped by two 806 nm LDs at 50 Hz repetition rate, while the intracavity pulse energy reached 6.25 mJ at 908 nm and 2.57 mJ at 1047 nm, maximum output pulse energy of 0.26 mJ at 486.4 nm wavelength was successfully achieved by intracavity sum-frequency. The corresponding spectral bandwidth was less than 0.08 nm, and the pulse width was about 11.8 ns. The peak power of the blue laser pulse was up to 21.8 kW, and the results provided a new blue pulsed laser source around 486 nm for ocean detection applications.
- 28 April 2023
- Published by IOP Publishing in Laser Physics Letters
- Vol. 20 (5) , 055001
486 nm pulsed Nd:YLF laser with intracavity sum-frequency mixing
An intracavity sum-frequency pulsed laser emitting at 486 nm was demonstrated in a combined cavity for two electro-optically Q-switched Nd:YLF fundamental lasers emitting at 908 nm and 1047 nm respectively. Pumped by two 806 nm LDs at 50 Hz repetition rate, while the intracavity pulse energy reached 6.25 mJ at 908 nm and 2.57 mJ at 1047 nm, maximum output pulse energy of 0.26 mJ at 486.4 nm wavelength was successfully achieved by intracavity sum-frequency. The corresponding spectral bandwidth was less than 0.08 nm, and the pulse width was about 11.8 ns. The peak power of the blue laser pulse was up to 21.8 kW, and the results provided a new blue pulsed laser source around 486 nm for ocean detection applications.
- Open Access
- 28 April 2023
- Published by MDPI AG in Remote Sensing
- Vol. 15 (9) , 2326
Faint Echo Extraction from ALB Waveforms Using a Point Cloud Semantic Segmentation Model
As an active remote sensing technology, airborne LIDAR can work at all times while emitting specific wavelengths of laser light that can penetrate seawater. Airborne LIDAR bathymetry (ALB) records an object’s full return waveform, including the water surface, water column, seafloor, and the objects on it. Due to the seawater’s absorption and scattering and the seafloor’s reflectivity effect, the seafloor’s amplitude of seafloor echoes varies greatly. Seafloor echoes with low signal-to-noise ratios are not easily detected using waveform processing methods, which can lead to insufficient seafloor topography depth and incomplete seafloor topography coverage. To extract faint seafloor echoes, we proposed a depth extraction method based on the PointConv deep learning model, called FWConv. The method assumed that spatially adjacent echoes were correlated. We converted all the spatially adjacent multi-frame waveforms into a point cloud. Each point represented a bin value in the waveform, and the points’ properties contained spatial coordinates and the amplitude in the waveform. In the semantic segmentation of these point clouds using deep learning models, we considered not only each centroid’s amplitude, but also its neighboring points’ distance and amplitude. This enriched the centroids’ features and allowed the model to better discriminate between background noise and seafloor echoes. The results showed that FWConv could extract faint seafloor echoes in the experimental area and was not easily affected by noise, and that the correctness reached 99.82%. The number of point clouds increased by 158%, and the seafloor elevation accuracy reached 0.20 m concerning the multibeam echo sounder data.
- 28 April 2023
- Published by MDPI AG in Remote Sensing
- Vol. 15 (9) , 2326
Open AccessFaint Echo Extraction from ALB Waveforms Using a Point Cloud Semantic Segmentation Model
As an active remote sensing technology, airborne LIDAR can work at all times while emitting specific wavelengths of laser light that can penetrate seawater. Airborne LIDAR bathymetry (ALB) records an object’s full return waveform, including the water surface, water column, seafloor, and the objects on it. Due to the seawater’s absorption and scattering and the seafloor’s reflectivity effect, the seafloor’s amplitude of seafloor echoes varies greatly. Seafloor echoes with low signal-to-noise ratios are not easily detected using waveform processing methods, which can lead to insufficient seafloor topography depth and incomplete seafloor topography coverage. To extract faint seafloor echoes, we proposed a depth extraction method based on the PointConv deep learning model, called FWConv. The method assumed that spatially adjacent echoes were correlated. We converted all the spatially adjacent multi-frame waveforms into a point cloud. Each point represented a bin value in the waveform, and the points’ properties contained spatial coordinates and the amplitude in the waveform. In the semantic segmentation of these point clouds using deep learning models, we considered not only each centroid’s amplitude, but also its neighboring points’ distance and amplitude. This enriched the centroids’ features and allowed the model to better discriminate between background noise and seafloor echoes. The results showed that FWConv could extract faint seafloor echoes in the experimental area and was not easily affected by noise, and that the correctness reached 99.82%. The number of point clouds increased by 158%, and the seafloor elevation accuracy reached 0.20 m concerning the multibeam echo sounder data.
- Open Access
- 18 February 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (2) , 318
Application of Flow Field Analysis in Ion Beam Figuring for Ultra-Smooth Machining of Monocrystalline Silicon Mirror
X-ray free-electron lasers are large modern scientific devices that play an important role in fields such as frontier physics and biomedicine. In this study, a light source is connected to an experimental station through beam lines, which requires numerous ultra-smooth and high-precision X-ray mirrors. Monocrystalline silicon is an ideal substrate material where ion-beam figuring is required. However, the ultra-smooth surface is damaged after the ion-beam figuring. Through an analysis of the machined surface, it is found that in the process of vacuum pumping, the impurities in the cavity adhere to the machined surface and increase the roughness after processing. Therefore, an optimized vacuum-pumping scheme is proposed. The experiment demonstrates that the original value of the processed surface roughness remains unchanged.
- 18 February 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (2) , 318
Open AccessApplication of Flow Field Analysis in Ion Beam Figuring for Ultra-Smooth Machining of Monocrystalline Silicon Mirror
X-ray free-electron lasers are large modern scientific devices that play an important role in fields such as frontier physics and biomedicine. In this study, a light source is connected to an experimental station through beam lines, which requires numerous ultra-smooth and high-precision X-ray mirrors. Monocrystalline silicon is an ideal substrate material where ion-beam figuring is required. However, the ultra-smooth surface is damaged after the ion-beam figuring. Through an analysis of the machined surface, it is found that in the process of vacuum pumping, the impurities in the cavity adhere to the machined surface and increase the roughness after processing. Therefore, an optimized vacuum-pumping scheme is proposed. The experiment demonstrates that the original value of the processed surface roughness remains unchanged.
- 1 January 2022
- Published by Shanghai Institute of Optics and Fine Mechanics in Chinese Optics Letters
- Vol. 20 (2) , 021403
Development of single-resonant optical parametric oscillator with tunable output from 410 nm to 630 nm
A single-resonant low-threshold type-I (BBO) optical parametric oscillator (OPO) with tunable output from 410 nm to 630 nm at 5 kHz repetition rate is reported. By taking the noncollinear phase matching method, low-threshold OPO operation could be obtained compared with the configuration of collinear phase matching, and the maximum optical–optical conversion efficiency of 11.8% was achieved at 500 nm wavelength when 0.4 mJ pump pulse energy was applied. When the noncollinearity angle was preset at 1.6°, 4.8°, and 6.3°, a continuously tuning output with a total spectral range of 220 nm was successfully obtained by adjusting the phase matching angle of the BBO crystal.- 1 January 2022
- Published by Shanghai Institute of Optics and Fine Mechanics in Chinese Optics Letters
- Vol. 20 (2) , 021403
Development of single-resonant optical parametric oscillator with tunable output from 410 nm to 630 nm
A single-resonant low-threshold type-I (BBO) optical parametric oscillator (OPO) with tunable output from 410 nm to 630 nm at 5 kHz repetition rate is reported. By taking the noncollinear phase matching method, low-threshold OPO operation could be obtained compared with the configuration of collinear phase matching, and the maximum optical–optical conversion efficiency of 11.8% was achieved at 500 nm wavelength when 0.4 mJ pump pulse energy was applied. When the noncollinearity angle was preset at 1.6°, 4.8°, and 6.3°, a continuously tuning output with a total spectral range of 220 nm was successfully obtained by adjusting the phase matching angle of the BBO crystal.- 24 November 2021
- Published by IOP Publishing in Laser Physics
- Vol. 32 (1) , 015801
Actively Q-switched Nd:YLF laser emitting at 908 nm
An actively Q-switched quasi-three-level Nd:YLF laser emitting at 908 nm, for the first time to our knowledge, was demonstrated. A RTP double-crystal scheme was used to realize electro-optical Q-switcher, and a L-shaped cavity structure was designed to suppress parasitic oscillation at 1047 nm. An 806 nm laser diode was used as the pump source with about 480 μ s pulse width. With 46.4 mJ pump pulse energy input at repetition rate of 100 Hz, maximum output pulse energies of 0.84 mJ and 0.73 mJ were obtained with output transmissions of 6.5% and 11%, respectively. The corresponding peak pulse powers were up to 14.3 kW and 12.1 kW, and the output pulse widths were 58.6 ns and 60.3 ns. The central laser wavelengths were both at 908.3 nm with spectral bandwidth of over 0.7 nm.
- 24 November 2021
- Published by IOP Publishing in Laser Physics
- Vol. 32 (1) , 015801
Actively Q-switched Nd:YLF laser emitting at 908 nm
An actively Q-switched quasi-three-level Nd:YLF laser emitting at 908 nm, for the first time to our knowledge, was demonstrated. A RTP double-crystal scheme was used to realize electro-optical Q-switcher, and a L-shaped cavity structure was designed to suppress parasitic oscillation at 1047 nm. An 806 nm laser diode was used as the pump source with about 480 μ s pulse width. With 46.4 mJ pump pulse energy input at repetition rate of 100 Hz, maximum output pulse energies of 0.84 mJ and 0.73 mJ were obtained with output transmissions of 6.5% and 11%, respectively. The corresponding peak pulse powers were up to 14.3 kW and 12.1 kW, and the output pulse widths were 58.6 ns and 60.3 ns. The central laser wavelengths were both at 908.3 nm with spectral bandwidth of over 0.7 nm.
- Open Access
- 1 September 2020
- Published by MDPI AG in Remote Sensing
- Vol. 12 (17) , 2844
A Dual-Wavelength Ocean Lidar for Vertical Profiling of Oceanic Backscatter and Attenuation
Ocean water column information profiles are essential for ocean research. Currently, water column profiles are typically obtained by ocean lidar instruments, including spaceborne, airborne and shipborne lidar, most of which are equipped with a 532 nm laser; however, blue wavelength penetrates more for open ocean detection. In this paper, we present a novel airborne dual-wavelength ocean lidar (DWOL), equipped with a 532 and 486 nm laser that can operate simultaneously. This instrument was designed to compare the performance of 486 and 532 nm lasers in a single detection area and to provide a reference for future spaceborne oceanic lidar (SBOL) design. Airborne and shipborne experiments were conducted in the South China Sea. Results show that—for a 500-frame accumulation—the 486 nm channel obtained volume profiles from a depth of approximately 100 m. In contrast, the vertical profiles obtained by the 532 nm channel only reached in a depth of 75 m, which was approximately 25% less than that of 486 m channel in the same detection area. Results from the inverse lidar attenuation coefficient for the DWOL show that the maximum value of ranged from 40 to 80 m, which was consistent with the chlorophyll-scattering layer (CSL) distribution measured by the shipborne instrument. Additionally, decreased for depth beyond 80 m, indicating that the 486 nm laser can potentially penetrate the entire CSL.- 1 September 2020
- Published by MDPI AG in Remote Sensing
- Vol. 12 (17) , 2844
Open AccessA Dual-Wavelength Ocean Lidar for Vertical Profiling of Oceanic Backscatter and Attenuation
Ocean water column information profiles are essential for ocean research. Currently, water column profiles are typically obtained by ocean lidar instruments, including spaceborne, airborne and shipborne lidar, most of which are equipped with a 532 nm laser; however, blue wavelength penetrates more for open ocean detection. In this paper, we present a novel airborne dual-wavelength ocean lidar (DWOL), equipped with a 532 and 486 nm laser that can operate simultaneously. This instrument was designed to compare the performance of 486 and 532 nm lasers in a single detection area and to provide a reference for future spaceborne oceanic lidar (SBOL) design. Airborne and shipborne experiments were conducted in the South China Sea. Results show that—for a 500-frame accumulation—the 486 nm channel obtained volume profiles from a depth of approximately 100 m. In contrast, the vertical profiles obtained by the 532 nm channel only reached in a depth of 75 m, which was approximately 25% less than that of 486 m channel in the same detection area. Results from the inverse lidar attenuation coefficient for the DWOL show that the maximum value of ranged from 40 to 80 m, which was consistent with the chlorophyll-scattering layer (CSL) distribution measured by the shipborne instrument. Additionally, decreased for depth beyond 80 m, indicating that the 486 nm laser can potentially penetrate the entire CSL. - Open Access
- 31 August 2020
- Published by MDPI AG in Remote Sensing
- Vol. 12 (17) , 2820
A Semianalytic Monte Carlo Simulator for Spaceborne Oceanic Lidar: Framework and Preliminary Results
Spaceborne lidar (light detection and ranging) is a very promising tool for the optical properties of global atmosphere and ocean detection. Although some studies have shown spaceborne lidar’s potential in ocean application, there is no spaceborne lidar specifically designed for ocean studies at present. In order to investigate the detection mechanism of the spaceborne lidar and analyze its detection performance, a spaceborne oceanic lidar simulator is established based on the semianalytic Monte Carlo (MC) method. The basic principle, the main framework, and the preliminary results of the simulator are presented. The whole process of the laser emitting, transmitting, and receiving is executed by the simulator with specific atmosphere–ocean optical properties and lidar system parameters. It is the first spaceborne oceanic lidar simulator for both atmosphere and ocean. The abilities of this simulator to characterize the effect of multiple scattering on the lidar signals of different aerosols, clouds, and seawaters with different scattering phase functions are presented. Some of the results of this simulator are verified by the lidar equation. It is confirmed that the simulator is beneficial to study the principle of spaceborne oceanic lidar and it can help develop a high-precision retrieval algorithm for the inherent optical properties (IOPs) of seawater.
- 31 August 2020
- Published by MDPI AG in Remote Sensing
- Vol. 12 (17) , 2820
Open AccessA Semianalytic Monte Carlo Simulator for Spaceborne Oceanic Lidar: Framework and Preliminary Results
Spaceborne lidar (light detection and ranging) is a very promising tool for the optical properties of global atmosphere and ocean detection. Although some studies have shown spaceborne lidar’s potential in ocean application, there is no spaceborne lidar specifically designed for ocean studies at present. In order to investigate the detection mechanism of the spaceborne lidar and analyze its detection performance, a spaceborne oceanic lidar simulator is established based on the semianalytic Monte Carlo (MC) method. The basic principle, the main framework, and the preliminary results of the simulator are presented. The whole process of the laser emitting, transmitting, and receiving is executed by the simulator with specific atmosphere–ocean optical properties and lidar system parameters. It is the first spaceborne oceanic lidar simulator for both atmosphere and ocean. The abilities of this simulator to characterize the effect of multiple scattering on the lidar signals of different aerosols, clouds, and seawaters with different scattering phase functions are presented. Some of the results of this simulator are verified by the lidar equation. It is confirmed that the simulator is beneficial to study the principle of spaceborne oceanic lidar and it can help develop a high-precision retrieval algorithm for the inherent optical properties (IOPs) of seawater.
- 27 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (5) , 231-234
5.6-mJ, Single-Frequency, End-Pumped Tm:Ho:LuLiF4 Slab Amplifier System
A nearly transform-limited, single-frequency 2 μm laser system with multi-stage of double-pass Tm: Ho: LuLiF4 slab amplifiers was demonstrated. An amplified pulse energy up to 5.6 mJ at central wavelength of 2051.9 nm was achieved successfully with around 429.7 ns pulse width at a repetition rate of 10 Hz. The line-width of the laser spectrum detected by a heterodyne technique was about 1.24 MHz. The M2 factors were less than 1.6 and 1.4 in the x and y directions, respectively.
- 27 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (5) , 231-234
5.6-mJ, Single-Frequency, End-Pumped Tm:Ho:LuLiF4 Slab Amplifier System
A nearly transform-limited, single-frequency 2 μm laser system with multi-stage of double-pass Tm: Ho: LuLiF4 slab amplifiers was demonstrated. An amplified pulse energy up to 5.6 mJ at central wavelength of 2051.9 nm was achieved successfully with around 429.7 ns pulse width at a repetition rate of 10 Hz. The line-width of the laser spectrum detected by a heterodyne technique was about 1.24 MHz. The M2 factors were less than 1.6 and 1.4 in the x and y directions, respectively.
- Open Access
- 21 January 2020
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 59 (01) , 014109-11
Performance validation on an all-fiber 1.54-μm pulsed coherent Doppler lidar for wind-profile measurement
Coherent Doppler lidar (CDL) has been developed as a powerful tool for atmospheric wind velocity measurement,1 – 4 aircraft wake-vortex hazard detection,5 – 7 and wind turbulence measurement8,9 with high temporal space resolution and high measurement accuracy due to its high carrier-to-noise detecting characteristics. The enabling modules for high-performance CDL system include laser transmitter,10 – 12 balanced detection,13,14 and weak-regime wind estimation algorithm.15,16 Adopting a single longitudinal mode laser and a balanced detector is helpful for a CDL to realize high signal-to-noise ratio (SNR). Recently, all-fiber pulsed CDL has attracted much attention due to its eye safety, compactness, flexible deployment, and mature fiber components from telecommunication industry.17- 21 January 2020
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 59 (01) , 014109-11
Open AccessPerformance validation on an all-fiber 1.54-μm pulsed coherent Doppler lidar for wind-profile measurement
Coherent Doppler lidar (CDL) has been developed as a powerful tool for atmospheric wind velocity measurement,1 – 4 aircraft wake-vortex hazard detection,5 – 7 and wind turbulence measurement8,9 with high temporal space resolution and high measurement accuracy due to its high carrier-to-noise detecting characteristics. The enabling modules for high-performance CDL system include laser transmitter,10 – 12 balanced detection,13,14 and weak-regime wind estimation algorithm.15,16 Adopting a single longitudinal mode laser and a balanced detector is helpful for a CDL to realize high signal-to-noise ratio (SNR). Recently, all-fiber pulsed CDL has attracted much attention due to its eye safety, compactness, flexible deployment, and mature fiber components from telecommunication industry.17 - Open Access
- 9 August 2019
- Published by MDPI AG in Remote Sensing
- Vol. 11 (16) , 1870
Validation of the Analytical Model of Oceanic Lidar Returns: Comparisons with Monte Carlo Simulations and Experimental Results
The analytical model based on the quasi-single small-angle scattering approximation can efficiently simulate oceanic lidar signals with multiple scattering; thus, its accuracy is of particular interest to scientists. In this paper, the model is modified to include refraction at oblique incidence and is then compared with Monte Carlo (MC) simulations and experimental results. Under different conditions, the results calculated by the analytical model demonstrate good agreement with the MC simulation and experimental data. The coefficient of determination R2 considering the logarithm of signals and the root mean square of the relative difference δ are R2 = 0.998 and δ = 10% in comparison with the semi-analytic MC simulation and R2 = 0.952 and δ = 46% for the lidar experiment. Thus, the results demonstrate the validity of the analytical model in the simulation of oceanic lidar signals.
- 9 August 2019
- Published by MDPI AG in Remote Sensing
- Vol. 11 (16) , 1870
Open AccessValidation of the Analytical Model of Oceanic Lidar Returns: Comparisons with Monte Carlo Simulations and Experimental Results
The analytical model based on the quasi-single small-angle scattering approximation can efficiently simulate oceanic lidar signals with multiple scattering; thus, its accuracy is of particular interest to scientists. In this paper, the model is modified to include refraction at oblique incidence and is then compared with Monte Carlo (MC) simulations and experimental results. Under different conditions, the results calculated by the analytical model demonstrate good agreement with the MC simulation and experimental data. The coefficient of determination R2 considering the logarithm of signals and the root mean square of the relative difference δ are R2 = 0.998 and δ = 10% in comparison with the semi-analytic MC simulation and R2 = 0.952 and δ = 46% for the lidar experiment. Thus, the results demonstrate the validity of the analytical model in the simulation of oceanic lidar signals.