Syechu Dwitya Nugraha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Syechu Dwitya Nugraha has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Ony Asrarul Qudsi
Politeknik Elektronika Negeri Surabaya
3 shared publications - Diah Septi Yanaratri
Politeknik Elektronika Negeri Surabaya
2 shared publications - Aditya Ilham Pradana1 shared publication
- Eka Prasetyono
Politeknik Elektronika Negeri Surabaya
1 shared publication - Epyk Sunarno
Politeknik Elektronika Negeri Surabaya
1 shared publication Era Purwanto
1 shared publication
Latest Publications
- Open Access
- 31 July 2023
- Published by Lembaga Penelitian dan Pengabdian kepada Masyarakat ITS in JAREE (Journal on Advanced Research in Electrical Engineering)
- Vol. 7 (2)
Temperature and Humidity Control System for 20 kV of Cubicle with Multiple Input Multiple Output Fuzzy Logic Controller
Cubicle 20 kV is a crucial electrical equipment in the 20 kV power distribution system. Often, cubicle issues arise due to excessively low or high temperatures and humidity, which can lead to the presence of water spots and corrosion on the components inside the 20 kV cubicle. One of the efforts to maintain the reliability of this 20 kV cubicle is to ensure that the temperature and humidity inside the cubicle remain within their operational limits. To achieve this, a system is needed to control the temperature and humidity in the 20 kV cubicle. The system can monitor and control the temperature and humidity inside the cubicle by adjusting the activation angle of the exhaust fan and heater. Control is achieved using a multiple-input, multiple-output fuzzy logic controller. The main components of this system are the STM32 microcontroller, DHT22 sensor, and ESP8266 module for monitoring temperature and humidity via a website. System has successfully controlled temperature and humidity d with a set point value of 35 °C and humidity of 60% RH. This implementation of fuzzy multiple input multiple outputs has performed well and resulted in only a small error of 0.55% for temperature and 1.05% for humidity.With the presence of this device, the temperature and humidity in the cubicle 20 kV can be controlled, and it enables the PLN operator to easily monitor and maintain the cubicle 20 kV.
- 31 July 2023
- Published by Lembaga Penelitian dan Pengabdian kepada Masyarakat ITS in JAREE (Journal on Advanced Research in Electrical Engineering)
- Vol. 7 (2)
Open AccessTemperature and Humidity Control System for 20 kV of Cubicle with Multiple Input Multiple Output Fuzzy Logic Controller
Cubicle 20 kV is a crucial electrical equipment in the 20 kV power distribution system. Often, cubicle issues arise due to excessively low or high temperatures and humidity, which can lead to the presence of water spots and corrosion on the components inside the 20 kV cubicle. One of the efforts to maintain the reliability of this 20 kV cubicle is to ensure that the temperature and humidity inside the cubicle remain within their operational limits. To achieve this, a system is needed to control the temperature and humidity in the 20 kV cubicle. The system can monitor and control the temperature and humidity inside the cubicle by adjusting the activation angle of the exhaust fan and heater. Control is achieved using a multiple-input, multiple-output fuzzy logic controller. The main components of this system are the STM32 microcontroller, DHT22 sensor, and ESP8266 module for monitoring temperature and humidity via a website. System has successfully controlled temperature and humidity d with a set point value of 35 °C and humidity of 60% RH. This implementation of fuzzy multiple input multiple outputs has performed well and resulted in only a small error of 0.55% for temperature and 1.05% for humidity.With the presence of this device, the temperature and humidity in the cubicle 20 kV can be controlled, and it enables the PLN operator to easily monitor and maintain the cubicle 20 kV.
- Open Access
- 21 July 2022
- Published by Politeknik Harapan Bersama Tegal in Power Elektronik : Jurnal Orang Elektro
- Vol. 11 (2) , 162-167
PENGATURAN KECEPATAN MOTOR BLDC SENSORLESS MENGGUNAKAN FOC
Motor BLDC populer di aplikasi alat elektronik dari rumah tangga ke industri karena beberapa kelebihan yang mereka miliki. Namun juga memiliki kekurangan dalam pemasangan sensor yang menyebabkan peningkatan biaya mengemudi motor. Dari masalah ini, penggunaan metode sensorless (menggunakan deteksi tegangan balik EMF) adalah solusi alternatif untuk menentukan pergantian inverter pada motor BLDC, juga menggunakan metode FOC untuk mengurangi kebisingan dan riak torsi pada motor dengan memanfaatkan kontrol PID untuk mempercepat dan menstabilkan kecepatan rotasi secara otomatis. Kinerja sistem telah diuji menggunakan Matlab. Hasil simulasi menunjukkan bahwa metode FOC menggunakan PID dapat meningkatkan respons sistem dinamis dan mengurangi nilai overshoot. Perubahan kecepatan dalam sistem ini telah berhasil mencapai set point 3000 rpm
- 21 July 2022
- Published by Politeknik Harapan Bersama Tegal in Power Elektronik : Jurnal Orang Elektro
- Vol. 11 (2) , 162-167
Open AccessPENGATURAN KECEPATAN MOTOR BLDC SENSORLESS MENGGUNAKAN FOC
Motor BLDC populer di aplikasi alat elektronik dari rumah tangga ke industri karena beberapa kelebihan yang mereka miliki. Namun juga memiliki kekurangan dalam pemasangan sensor yang menyebabkan peningkatan biaya mengemudi motor. Dari masalah ini, penggunaan metode sensorless (menggunakan deteksi tegangan balik EMF) adalah solusi alternatif untuk menentukan pergantian inverter pada motor BLDC, juga menggunakan metode FOC untuk mengurangi kebisingan dan riak torsi pada motor dengan memanfaatkan kontrol PID untuk mempercepat dan menstabilkan kecepatan rotasi secara otomatis. Kinerja sistem telah diuji menggunakan Matlab. Hasil simulasi menunjukkan bahwa metode FOC menggunakan PID dapat meningkatkan respons sistem dinamis dan mengurangi nilai overshoot. Perubahan kecepatan dalam sistem ini telah berhasil mencapai set point 3000 rpm
- Open Access
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1367 (1) , 012058
Design and implementation bidirectional SEPIC/ZETA converter using Fuzzy Logic Controller in DC microgrid application
The electrical energy has been dependent on fossil fuels, but the availability of fossil energy is running low with increasing electricity demand in society. Therefore a lot of research is done on renewable energy sources, one of which is solar energy. Solar energy can be applied to home scale DC microgrid systems. In the DC microgrid system the independent source of energy for the supply of loads comes from two sources, namely DC bus and 120 volt battery. To combine these two energy sources, a bidirectional converter is needed which will regulate power flow and electricity storage. In this system the battery can become a burden and can be a source of energy in the same series. Bidirectional converters can work in two directions, namely charging mode and discharging mode. The type of converter used in this bidirectional converter is SEPIC/ZETA Converter. The use of this type of converter is expected to reduce the ripple at the output voltage and minimize voltage disturbances during switching. The control method used is a fuzzy logic controller for voltage control which is expected to produce stable output.
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1367 (1) , 012058
Open AccessDesign and implementation bidirectional SEPIC/ZETA converter using Fuzzy Logic Controller in DC microgrid application
The electrical energy has been dependent on fossil fuels, but the availability of fossil energy is running low with increasing electricity demand in society. Therefore a lot of research is done on renewable energy sources, one of which is solar energy. Solar energy can be applied to home scale DC microgrid systems. In the DC microgrid system the independent source of energy for the supply of loads comes from two sources, namely DC bus and 120 volt battery. To combine these two energy sources, a bidirectional converter is needed which will regulate power flow and electricity storage. In this system the battery can become a burden and can be a source of energy in the same series. Bidirectional converters can work in two directions, namely charging mode and discharging mode. The type of converter used in this bidirectional converter is SEPIC/ZETA Converter. The use of this type of converter is expected to reduce the ripple at the output voltage and minimize voltage disturbances during switching. The control method used is a fuzzy logic controller for voltage control which is expected to produce stable output.
- Open Access
- 22 November 2018
- Published by Universitas Gadjah Mada in Jurnal Nasional Teknik Elektro dan Teknologi Informasi
- Vol. 7 (4)
Manajemen dan Pemantauan Energi Motor BLDC pada Mobil Listrik Berbasis IoT
Manajemen dan Pemantauan Energi Motor BLDC pada Mobil Listrik Berbasis IoT
- 22 November 2018
- Published by Universitas Gadjah Mada in Jurnal Nasional Teknik Elektro dan Teknologi Informasi
- Vol. 7 (4)
Open AccessManajemen dan Pemantauan Energi Motor BLDC pada Mobil Listrik Berbasis IoT
Manajemen dan Pemantauan Energi Motor BLDC pada Mobil Listrik Berbasis IoT
- Open Access
- 8 August 2018
- Published by Politeknik Negeri Bengkalis in INOVTEK POLBENG
- Vol. 8 (1) , 67-73
IMPLEMENTASI CURRENT FED PUSH PULL CONVERTER MENGGUNAKAN KONTROL PI PADA APLIKASI RUMAH MANDIRI
Aplikasi dari pemanfaatan energi matahari adalah sebuah mikrogrid skala rumah. Pada mikrogrid khususnya menggunakan panel surya atau photovoltaic (PV) sebagai sumber energi utama. Pada aplikasinya tegangan keluaran dari PV dinaikkan atau diturunkan dengan DC-DC konverter. Akan tetapi permasalahan yang terjadi adalah daya atau tegangan keluaran dari PV mudah berubah terhadap irradiasi matahari sehingga perlu dinaikkan dengan rating kelipatan tegangan yang tinggi mencapai 400 V untuk suplai DC bus bar. Maka dari itu pada penelitian ini akan mengaplikasikan Current Fed Push Pull Converter dengan menggunakan kontrol PI yang dapat menaikkan tegangan masukan yang bernilai 70V - 95 V menjadi 400 V dan distabilkan menggunakan metode PI. Dari hasil implementasi, sistem mampu menaikkan tegangan keluaran 400 V dan menjaga tegangan tersebut tetap stabil walaupun tegangan masukannya berubah-ubah
- 8 August 2018
- Published by Politeknik Negeri Bengkalis in INOVTEK POLBENG
- Vol. 8 (1) , 67-73
Open AccessIMPLEMENTASI CURRENT FED PUSH PULL CONVERTER MENGGUNAKAN KONTROL PI PADA APLIKASI RUMAH MANDIRI
Aplikasi dari pemanfaatan energi matahari adalah sebuah mikrogrid skala rumah. Pada mikrogrid khususnya menggunakan panel surya atau photovoltaic (PV) sebagai sumber energi utama. Pada aplikasinya tegangan keluaran dari PV dinaikkan atau diturunkan dengan DC-DC konverter. Akan tetapi permasalahan yang terjadi adalah daya atau tegangan keluaran dari PV mudah berubah terhadap irradiasi matahari sehingga perlu dinaikkan dengan rating kelipatan tegangan yang tinggi mencapai 400 V untuk suplai DC bus bar. Maka dari itu pada penelitian ini akan mengaplikasikan Current Fed Push Pull Converter dengan menggunakan kontrol PI yang dapat menaikkan tegangan masukan yang bernilai 70V - 95 V menjadi 400 V dan distabilkan menggunakan metode PI. Dari hasil implementasi, sistem mampu menaikkan tegangan keluaran 400 V dan menjaga tegangan tersebut tetap stabil walaupun tegangan masukannya berubah-ubah