Mahdi Tabatabaei Malazi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mahdi Tabatabaei Malazi has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Emir Taha Eren
Faculty of Mechanical Engineering, Yildiz Technical University, Besiktas, Istanbul 34349, Turkey
2 shared publications - Galip Temir
Faculty of Mechanical Engineering, Yildiz Technical University, Besiktas, Istanbul 34349, Turkey
2 shared publications - Jing Luo
State Key Laboratory of Hydraulics and Mountain River Engineering, Sichuan University, Chengdu 610065, China
1 shared publication - Mingming Liu
School of Architecture and Engineering, Liaocheng University, Liaocheng 252000, China
1 shared publication - Shuo Mi
State Key Laboratory of Hydraulics and Mountain River Engineering, Sichuan University, Chengdu 610065, China
1 shared publication - Shuo Mi
State Key Laboratory of Hydraulics and Mountain River Engineering, Sichuan University, Chengdu 610500, China
1 shared publication
Latest Publications
- Open Access
- 15 September 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (9) , 714
Three-Dimensional Fluid–Structure Interaction Case Study on Elastic Beam
A three-dimensional T-shaped flexible beam deformation was investigated using model experiments and numerical simulations. In the experiment, a beam was placed in a recirculating water channel with a steady uniform flow in the inlet. A high-speed camera system (HSC) was utilized to record the T-shaped flexible beam deformation in the cross-flow direction. In addition, a two-way fluid-structure interaction (FSI) numerical method was employed to simulate the deformation of the T-shaped flexible beam. A system coupling was used for conjoining the fluid and solid domain. The dynamic mesh method was used for recreating the mesh. After the validation of the three-dimensional numerical T-shaped flexible solid beam with the HSC results, deformation and stress were calculated for different Reynolds numbers. This study exhibited that the deformation of the T-shaped flexible beam increases by nearly 90% when the velocity is changed from 0.25 to 0.35 m/s, whereas deformation of the T-shaped flexible beam decreases by nearly 63% when the velocity is varied from 0.25 to 0.15 m/s.
- 15 September 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (9) , 714
Open AccessThree-Dimensional Fluid–Structure Interaction Case Study on Elastic Beam
A three-dimensional T-shaped flexible beam deformation was investigated using model experiments and numerical simulations. In the experiment, a beam was placed in a recirculating water channel with a steady uniform flow in the inlet. A high-speed camera system (HSC) was utilized to record the T-shaped flexible beam deformation in the cross-flow direction. In addition, a two-way fluid-structure interaction (FSI) numerical method was employed to simulate the deformation of the T-shaped flexible beam. A system coupling was used for conjoining the fluid and solid domain. The dynamic mesh method was used for recreating the mesh. After the validation of the three-dimensional numerical T-shaped flexible solid beam with the HSC results, deformation and stress were calculated for different Reynolds numbers. This study exhibited that the deformation of the T-shaped flexible beam increases by nearly 90% when the velocity is changed from 0.25 to 0.35 m/s, whereas deformation of the T-shaped flexible beam decreases by nearly 63% when the velocity is varied from 0.25 to 0.15 m/s.
- Open Access
Numerical Investigation on the Collision between a Solitary Wave and a Moving Cylinder
A 2-D numerical wave tank (NWT) was applied for solving the interaction between a solitary wave and a moving circular cylinder. The cylinder was placed at various positions from the tank bed floor. The cylinder can move at a constant horizontal velocity towards the solitary wave. The collision between a solitary wave and a moving cylinder is investigated at various conditions. A total of fifteen cases were studied. Ten different numerical simulations were used, including five submergence depths and two different moving velocities. The other five different numerical simulations were studied when the cylinder was unmoved in the NWT for comparing wave-structure interaction results between the moving and unmoved cylinders. The numerical results were obtained by calculating Reynolds-Averaged Navier-Stokes (RANS) equations and the volume of fluid (VOF) equations. Two different codes (User-Define-Function-UDF) were used for the generation of a solitary wave by moving a wave paddle and traveling cylinder in the NWT. The dynamic mesh method was applied for recreating mesh. First, the ability of CFD codes to generate a solitary wave by using wave paddle movement and the hydrodynamic forces of a moving cylinder were validated by numerical results. Further, the free-surface elevation and hydrodynamic forces were considered at various conditions. The numerical results show that moving cylinder velocity and the space between the cylinder and the tank bed floor have significant effects on surface displacement and hydrodynamic forces.
Open AccessNumerical Investigation on the Collision between a Solitary Wave and a Moving Cylinder
A 2-D numerical wave tank (NWT) was applied for solving the interaction between a solitary wave and a moving circular cylinder. The cylinder was placed at various positions from the tank bed floor. The cylinder can move at a constant horizontal velocity towards the solitary wave. The collision between a solitary wave and a moving cylinder is investigated at various conditions. A total of fifteen cases were studied. Ten different numerical simulations were used, including five submergence depths and two different moving velocities. The other five different numerical simulations were studied when the cylinder was unmoved in the NWT for comparing wave-structure interaction results between the moving and unmoved cylinders. The numerical results were obtained by calculating Reynolds-Averaged Navier-Stokes (RANS) equations and the volume of fluid (VOF) equations. Two different codes (User-Define-Function-UDF) were used for the generation of a solitary wave by moving a wave paddle and traveling cylinder in the NWT. The dynamic mesh method was applied for recreating mesh. First, the ability of CFD codes to generate a solitary wave by using wave paddle movement and the hydrodynamic forces of a moving cylinder were validated by numerical results. Further, the free-surface elevation and hydrodynamic forces were considered at various conditions. The numerical results show that moving cylinder velocity and the space between the cylinder and the tank bed floor have significant effects on surface displacement and hydrodynamic forces.
- Open Access
Numerical Study of Highly Viscous Fluid Sloshing in the Real-Scale Membrane-Type Tank
The highly viscous liquid (glycerin) sloshing is investigated numerically in this study. The full-scale membrane-type tank is considered. The numerical investigation is performed by applying a two-phase numerical model based on the spatially averaged Navier-Stokes equations. Firstly, the numerical model is validated against the available numerical model and a self-conducted experiment then is applied to systematically investigate the full-scale sloshing. In this study, two filling levels (50% and 70% of the tank height) are considered. The fluid kinematic viscosity is fixed at a value being 6.0 × 10−5 m2/s with comparative value to that of the crude oil. A wide range of forcing periods varying from 8.0 s to 12.0 s are used to identify the response process of pressures as well as free surface displacements. The pressures are analyzed along with breaking free surface snapshots and corresponding pressure distributions. The slamming effects are also demonstrated. Finally, the frequency response is further identified by the fast Fourier transformation technology.
Open AccessNumerical Study of Highly Viscous Fluid Sloshing in the Real-Scale Membrane-Type Tank
The highly viscous liquid (glycerin) sloshing is investigated numerically in this study. The full-scale membrane-type tank is considered. The numerical investigation is performed by applying a two-phase numerical model based on the spatially averaged Navier-Stokes equations. Firstly, the numerical model is validated against the available numerical model and a self-conducted experiment then is applied to systematically investigate the full-scale sloshing. In this study, two filling levels (50% and 70% of the tank height) are considered. The fluid kinematic viscosity is fixed at a value being 6.0 × 10−5 m2/s with comparative value to that of the crude oil. A wide range of forcing periods varying from 8.0 s to 12.0 s are used to identify the response process of pressures as well as free surface displacements. The pressures are analyzed along with breaking free surface snapshots and corresponding pressure distributions. The slamming effects are also demonstrated. Finally, the frequency response is further identified by the fast Fourier transformation technology.