Nagaraj K. Arakere
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nagaraj K. Arakere has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Abir Bhattacharyya
Department of Materials Engineering Indian Institute of Technology Jodhpur Karwar Rajasthan India
2 shared publications Ghatu Subhash
Department of Mechanical and Aerospace Engineering, University of Florida 1 , Gainesville, FL32611
2 shared publications- Ghatu Subhash
Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, USA
2 shared publications - Gilda Ham-Battista
ERC, Inc., Huntsville, AL
2 shared publications - Gregory R. Swanson
NASA Marshall Space Center Flight Center, ED22, Structural Mechanics Group, Huntsville, AL
2 shared publications - Phillip A. Allen
NASA Marshall Space Flight Center, MSFC, Huntsville, AL, USA
2 shared publications
Latest Publications
- 6 November 2019
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 43 (3) , 539-549
Accounting for microstructure sensitivity and plasticity in life prediction of heavily loaded contacts under rolling contact fatigue
Probabilistic models employed for life prediction in the bearing industry (Lundberg‐Palmgren [LP], Ioannides‐Harris [IH], and Zatersky models) utilize stresses calculated based on Hertzian assumptions that ignore plastic deformation occurring under high radial loads. However, it is known that subsurface plasticity produces significant deviations from elastic calculations in contact dimensions, pressure, and stresses. In this work, we show that accounting for plastic deformation leads to significantly more accurate life predictions than the general practice of utilizing elastic stress fields. Conventional probabilistic models are also restricted to utilizing stress measures at the macroscopic scale, while the onset of damage under rolling contact fatigue (RCF) manifests on a much smaller scale. By utilizing Dang Van criterion (DVC)—a multiscale high cycle fatigue criterion—in a probabilistic framework to account for stresses at multiple length scales, we propose a formulation that is second in accuracy only to the Zaretsky model, thus outperforming LP and IH models. Thus, we improve the accuracy of conventional probabilistic models by accounting for plastic deformation, while also presenting a new microstructure‐sensitive probabilistic formulation that betters their predictions.
- 6 November 2019
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 43 (3) , 539-549
Accounting for microstructure sensitivity and plasticity in life prediction of heavily loaded contacts under rolling contact fatigue
Probabilistic models employed for life prediction in the bearing industry (Lundberg‐Palmgren [LP], Ioannides‐Harris [IH], and Zatersky models) utilize stresses calculated based on Hertzian assumptions that ignore plastic deformation occurring under high radial loads. However, it is known that subsurface plasticity produces significant deviations from elastic calculations in contact dimensions, pressure, and stresses. In this work, we show that accounting for plastic deformation leads to significantly more accurate life predictions than the general practice of utilizing elastic stress fields. Conventional probabilistic models are also restricted to utilizing stress measures at the macroscopic scale, while the onset of damage under rolling contact fatigue (RCF) manifests on a much smaller scale. By utilizing Dang Van criterion (DVC)—a multiscale high cycle fatigue criterion—in a probabilistic framework to account for stresses at multiple length scales, we propose a formulation that is second in accuracy only to the Zaretsky model, thus outperforming LP and IH models. Thus, we improve the accuracy of conventional probabilistic models by accounting for plastic deformation, while also presenting a new microstructure‐sensitive probabilistic formulation that betters their predictions.
- 29 September 2017
- Published by ASME International in Journal of Tribology
- Vol. 140 (2) , 021401
Extended Hertz Theory of Contact Mechanics for Case-Hardened Steels With Implications for Bearing Fatigue Life
The analytical expressions currently available for Hertzian contact stresses are applicable only for homogeneous materials and not for case-hardened bearing steels, which have inhomogeneous microstructure and graded elastic properties in the subsurface region. Therefore, this article attempts to determine subsurface stress fields in ball bearings for graded materials with different ball and raceway geometries in contact. Finite element models were developed to simulate ball-on-raceway elliptical contact and ball-on-plate axisymmetric contact, to study the effects of elastic modulus variation with depth due to case hardening. Ball bearings with low, moderate, and heavy load conditions are considered. The peak contact pressure for case-hardened steel is always more than that of through-hardened steel under identical geometry and loading conditions. Using equivalent contact pressure approach, effective elastic modulus is determined for case-carburized steels, which will enable the use of Hertz equations for different gradations in elastic modulus of raceway material. Nonlinear regression tools are used to predict effective elastic modulus as a weighted sum of surface and core elastic moduli of raceway material and design parameters of ball–raceway contact area. Mesh convergence study and validation of equivalent contact pressure approach are also provided. Implications of subsurface stress variation due to case hardening on bearing fatigue life are discussed.
- 29 September 2017
- Published by ASME International in Journal of Tribology
- Vol. 140 (2) , 021401
Extended Hertz Theory of Contact Mechanics for Case-Hardened Steels With Implications for Bearing Fatigue Life
The analytical expressions currently available for Hertzian contact stresses are applicable only for homogeneous materials and not for case-hardened bearing steels, which have inhomogeneous microstructure and graded elastic properties in the subsurface region. Therefore, this article attempts to determine subsurface stress fields in ball bearings for graded materials with different ball and raceway geometries in contact. Finite element models were developed to simulate ball-on-raceway elliptical contact and ball-on-plate axisymmetric contact, to study the effects of elastic modulus variation with depth due to case hardening. Ball bearings with low, moderate, and heavy load conditions are considered. The peak contact pressure for case-hardened steel is always more than that of through-hardened steel under identical geometry and loading conditions. Using equivalent contact pressure approach, effective elastic modulus is determined for case-carburized steels, which will enable the use of Hertz equations for different gradations in elastic modulus of raceway material. Nonlinear regression tools are used to predict effective elastic modulus as a weighted sum of surface and core elastic moduli of raceway material and design parameters of ball–raceway contact area. Mesh convergence study and validation of equivalent contact pressure approach are also provided. Implications of subsurface stress variation due to case hardening on bearing fatigue life are discussed.
- 12 September 2017
- Published by ASTM International in Materials Performance and Characterization
- Vol. 6 (4) , 656-677
A New Approach Towards Life Prediction of Case Hardened Bearing Steels Subjected to Rolling Contact Fatigue
- 12 September 2017
- Published by ASTM International in Materials Performance and Characterization
- Vol. 6 (4) , 656-677
A New Approach Towards Life Prediction of Case Hardened Bearing Steels Subjected to Rolling Contact Fatigue
- 1 October 2015
- Published by ASME International in Journal of Tribology
- Vol. 137 (4) , 041102
Cyclic Constitutive Response and Effective S–N Diagram of M50 NiL Case-Hardened Bearing Steel Subjected to Rolling Contact Fatigue
A combined experimental and numerical method is developed to estimate the continuously evolving cyclic plastic strain amplitudes in plastically deformed subsurface regions of a case-hardened M50 NiL steel rod subjected to rolling contact fatigue (RCF) over several hundred million cycles. The subsurface hardness values measured over the entire plastically deformed regions and the elastoplastic von Mises stresses determined from the three-dimensional (3D) Hertzian contact finite element (FE) model have been used in conjunction with Neuber's rule to estimate the evolved cyclic plastic strain amplitudes at various points within the RCF-affected zone. The cyclic stress–strain plots developed as a function of case depth revealed that cyclic hardening exponent of the material is greater than the monotonic strain-hardening exponent. Effective S–N diagram for the RCF loading of the case-hardened steel has been presented and the effect of compressive mean stress on its fatigue strength has been explained using Haigh diagram. The compressive mean stress correction according to Haigh diagram predicts that the allowable fatigue strength of the steel increases by a factor of two compared to its fatigue limit before mean stress correction, thus potentially allowing the rolling element bearings to operate over several hundred billion cycles. The methodology presented here is generalized and can be adopted to obtain the constitutive response and S–N diagrams of both through- and case-hardened steels subjected to RCF.
- 1 October 2015
- Published by ASME International in Journal of Tribology
- Vol. 137 (4) , 041102
Cyclic Constitutive Response and Effective S–N Diagram of M50 NiL Case-Hardened Bearing Steel Subjected to Rolling Contact Fatigue
A combined experimental and numerical method is developed to estimate the continuously evolving cyclic plastic strain amplitudes in plastically deformed subsurface regions of a case-hardened M50 NiL steel rod subjected to rolling contact fatigue (RCF) over several hundred million cycles. The subsurface hardness values measured over the entire plastically deformed regions and the elastoplastic von Mises stresses determined from the three-dimensional (3D) Hertzian contact finite element (FE) model have been used in conjunction with Neuber's rule to estimate the evolved cyclic plastic strain amplitudes at various points within the RCF-affected zone. The cyclic stress–strain plots developed as a function of case depth revealed that cyclic hardening exponent of the material is greater than the monotonic strain-hardening exponent. Effective S–N diagram for the RCF loading of the case-hardened steel has been presented and the effect of compressive mean stress on its fatigue strength has been explained using Haigh diagram. The compressive mean stress correction according to Haigh diagram predicts that the allowable fatigue strength of the steel increases by a factor of two compared to its fatigue limit before mean stress correction, thus potentially allowing the rolling element bearings to operate over several hundred billion cycles. The methodology presented here is generalized and can be adopted to obtain the constitutive response and S–N diagrams of both through- and case-hardened steels subjected to RCF.
- 1 January 2012
- Published by SAGE Publications in Materials Science and Technology
- Vol. 28 (1) , 34-38
Work hardening response of M50-NiL case hardened bearing steel during shakedown in rolling contact fatigue
The work hardening response during shakedown phase for case hardened M50-NiL bearing steel in rolling contact fatigue (RCF) is presented. Rolling contact fatigue testing is performed using a ball rod tester for varying cycles and Hertzian stress of 5·5 GPa on multiple test tracks of a case hardened rod. Longitudinal sectioning and polishing of the test rod reveal the RCF affected zones. Micro-Vickers indentation mapping of the subsurface zones is used to measure workhardening. A maximum increase in hardness from 7·4 to 8·3 GPa was observed at ∼13·5×106 cycles, after which hardness saturated. A finite element simulation of the RCF test was performed to predict the increase in hardness. It is hypothesised that plastic strain accumulation around the hard carbide inclusions results in increased hardness. Cyclic hardening likely saturates when the ratchet strain per cycle approaches zero. Plastic shakedown follows with no further accumulation of plastic strain and marks the beginning of steady state response.
- 1 January 2012
- Published by SAGE Publications in Materials Science and Technology
- Vol. 28 (1) , 34-38
Work hardening response of M50-NiL case hardened bearing steel during shakedown in rolling contact fatigue
The work hardening response during shakedown phase for case hardened M50-NiL bearing steel in rolling contact fatigue (RCF) is presented. Rolling contact fatigue testing is performed using a ball rod tester for varying cycles and Hertzian stress of 5·5 GPa on multiple test tracks of a case hardened rod. Longitudinal sectioning and polishing of the test rod reveal the RCF affected zones. Micro-Vickers indentation mapping of the subsurface zones is used to measure workhardening. A maximum increase in hardness from 7·4 to 8·3 GPa was observed at ∼13·5×106 cycles, after which hardness saturated. A finite element simulation of the RCF test was performed to predict the increase in hardness. It is hypothesised that plastic strain accumulation around the hard carbide inclusions results in increased hardness. Cyclic hardening likely saturates when the ratchet strain per cycle approaches zero. Plastic shakedown follows with no further accumulation of plastic strain and marks the beginning of steady state response.
- 1 July 2011
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 78 (10) , 2097-2114
J–Q characterized stress fields of surface-cracked metallic liners – II. Composite overwrapped pressure vessels
- 1 July 2011
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 78 (10) , 2097-2114
J–Q characterized stress fields of surface-cracked metallic liners – II. Composite overwrapped pressure vessels
- 4 October 2009
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 77 (1) , 170-181
J–T characterized stress fields of surface-cracked metallic liners bonded to a structural backing – I. Uniaxial tension
- 4 October 2009
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 77 (1) , 170-181
J–T characterized stress fields of surface-cracked metallic liners bonded to a structural backing – I. Uniaxial tension
- Top Cited Papers
- 24 September 2009
- Published by ASME International in Journal of Tribology
- Vol. 131 (4) , 041403
A Review of Rolling Contact Fatigue
Ball and rolling element bearings are perhaps the most widely used components in industrial machinery. They are used to support load and allow relative motion inherent in the mechanism to take place. Subsurface originated spalling has been recognized as one of the main modes of failure for rolling contact fatigue (RCF) of bearings. In the past few decades a significant number of investigators have attempted to determine the physical mechanisms involved in rolling contact fatigue of bearings and proposed models to predict their fatigue lives. In this paper, some of the most widely used RCF models are reviewed and discussed, and their limitations are addressed. The paper also presents the modeling approaches recently proposed by the authors to develop life models and better understanding of the RCF.
- 24 September 2009
- Published by ASME International in Journal of Tribology
- Vol. 131 (4) , 041403
Top Cited PapersA Review of Rolling Contact Fatigue
Ball and rolling element bearings are perhaps the most widely used components in industrial machinery. They are used to support load and allow relative motion inherent in the mechanism to take place. Subsurface originated spalling has been recognized as one of the main modes of failure for rolling contact fatigue (RCF) of bearings. In the past few decades a significant number of investigators have attempted to determine the physical mechanisms involved in rolling contact fatigue of bearings and proposed models to predict their fatigue lives. In this paper, some of the most widely used RCF models are reviewed and discussed, and their limitations are addressed. The paper also presents the modeling approaches recently proposed by the authors to develop life models and better understanding of the RCF.
- 26 March 2008
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 130 (3) , 032501
A Fracture-Mechanics-Based Methodology for Fatigue Life Prediction of Single Crystal Nickel-Based Superalloys
A comprehensive fracture-mechanics-based life prediction methodology is presented for fcc single crystal components based on the computation of stress intensity factors (SIFs), and the modeling of the crystallographic fatigue crack growth (FCG) process under mixed-mode loading conditions. The 3D finite element numerical procedure presented for computing SIFs for anisotropic materials under mixed-mode loading is very general and not just specific to fcc single crystals. SIFs for a Brazilian disk specimen are presented for the crack on the {111}) plane in the ⟨101⟩ and ⟨121⟩ directions, which represent the primary and secondary slip directions. Variation of SIFs as a function of thickness is also presented. Modeling of the crystallographic FCG behavior is performed by using the resolved shear stress intensity coefficient, . This parameter is sensitive to the grain orientation and is based on the resolved shear stresses on the slip planes at the crack tip, which is useful in identifying the active crack plane as well as in predicting the crack growth direction. A multiaxial fatigue crack driving force parameter, , was quantified, which can be used to predict the FCG rate and, hence, life in single crystal components subject to mixed-mode fatigue loading.- 26 March 2008
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 130 (3) , 032501
A Fracture-Mechanics-Based Methodology for Fatigue Life Prediction of Single Crystal Nickel-Based Superalloys
A comprehensive fracture-mechanics-based life prediction methodology is presented for fcc single crystal components based on the computation of stress intensity factors (SIFs), and the modeling of the crystallographic fatigue crack growth (FCG) process under mixed-mode loading conditions. The 3D finite element numerical procedure presented for computing SIFs for anisotropic materials under mixed-mode loading is very general and not just specific to fcc single crystals. SIFs for a Brazilian disk specimen are presented for the crack on the {111}) plane in the ⟨101⟩ and ⟨121⟩ directions, which represent the primary and secondary slip directions. Variation of SIFs as a function of thickness is also presented. Modeling of the crystallographic FCG behavior is performed by using the resolved shear stress intensity coefficient, . This parameter is sensitive to the grain orientation and is based on the resolved shear stresses on the slip planes at the crack tip, which is useful in identifying the active crack plane as well as in predicting the crack growth direction. A multiaxial fatigue crack driving force parameter, , was quantified, which can be used to predict the FCG rate and, hence, life in single crystal components subject to mixed-mode fatigue loading.- 1 January 2006
- Published by ASME International
- Vol. 2006, 1003-1016
A Fracture Mechanics Based Methodology for Fatigue Life Prediction of Single Crystal Nickel Based Superalloys
A comprehensive fracture mechanics based life prediction methodology is presented for FCC (Face Centered Cubic) single crystal components, based on computation of stress intensity factors (SIFs), and modeling the crystallographic fatigue crack growth process, under mixed-mode loading conditions. The 3D finite element numerical procedure presented for computing SIFs for anisotropic materials under mixed-mode loading is very general, and not just specific to FCC single crystals. Stress intensity factors for a Brazilian Disc (BD) specimen are presented for the crack on the {111} plane in the 〈101〉 and 〈121〉 directions, which represent the primary and secondary slip directions. Variation of SIFs as a function of thickness is also presented. Modeling of the crystallographic fatigue crack growth (FCG) behavior is performed by using the resolved shear stress intensity coefficient (RSSIC), Krss. This parameter is sensitive to the grain orientation and is based on the resolved shear stresses on the slip planes at the crack tip, which is useful in identifying the active crack plane as well as predicting the crack growth direction. A multiaxial fatigue crack driving force parameter, ΔKrss, was quantified, which can be used to predict the FCG rate and hence life in single crystal components subject to mixed mode fatigue loading.
- 1 January 2006
- Published by ASME International
- Vol. 2006, 1003-1016
A Fracture Mechanics Based Methodology for Fatigue Life Prediction of Single Crystal Nickel Based Superalloys
A comprehensive fracture mechanics based life prediction methodology is presented for FCC (Face Centered Cubic) single crystal components, based on computation of stress intensity factors (SIFs), and modeling the crystallographic fatigue crack growth process, under mixed-mode loading conditions. The 3D finite element numerical procedure presented for computing SIFs for anisotropic materials under mixed-mode loading is very general, and not just specific to FCC single crystals. Stress intensity factors for a Brazilian Disc (BD) specimen are presented for the crack on the {111} plane in the 〈101〉 and 〈121〉 directions, which represent the primary and secondary slip directions. Variation of SIFs as a function of thickness is also presented. Modeling of the crystallographic fatigue crack growth (FCG) behavior is performed by using the resolved shear stress intensity coefficient (RSSIC), Krss. This parameter is sensitive to the grain orientation and is based on the resolved shear stresses on the slip planes at the crack tip, which is useful in identifying the active crack plane as well as predicting the crack growth direction. A multiaxial fatigue crack driving force parameter, ΔKrss, was quantified, which can be used to predict the FCG rate and hence life in single crystal components subject to mixed mode fatigue loading.