Smitha Ankanahalli Shankaregowda

Developing an eco-friendly, flexible and recyclable micro-structured dry electrode for sustainable life is essential. In this work, we have developed irregular, micro-structured sandpaper coated with graphite powder as an electrode for developing a simple, low-cost, contact-separation mode graphite-coated sandpaper-based triboelectric nanogenerator (GS-TENG) as a self-powered device and biomechanical sensor. The as-fabricated GS-TENG is a dielectric-conductor model. It is made up of a bottom layer with polytetrafluoroethylene (PTFE) as a triboelectric layer, which is attached onto a graphite-coated sandpaper-based electrode and a top layer with aluminum as another triboelectric layer as well as an electrode. The forward and reverse open-circuit voltages reach upto ~33.8 V and ~36.62 V respectively, and the forward and reverse short-circuit currents are ~2.16 µA and ~2.17µA, respectively. The output generated by GS-TENG can power 120 blue light-emitting diodes connected in series, liquid crystal display and can charge commercial capacitors along with the rectifier circuit. The capacitor of 22 µF is charged upto 5 V and is sufficient to drive digital watch as wearable electronics. Moreover, the device can track signals generated by human motion, hence it scavenges biomechanical energy. Thus, GS-TENG facilitates large-scale fabrication and has potential for future applications in wearable and portable devices.

Transfer method of chemically vapor deposition graphene is an appealing issue to realize its application as flexible and transparent electrodes. A universal stamping method to transfer as grown graphene from copper onto different flexible and transparent polymers (FTPs) reported here ensures simple, robust, rapid, clean and low-cost. This method relies on coating ethylene vinyl acetate (EVA) onto the as grown graphene, binding EVA coated graphene/Cu with FTPs and delamination by hydrogen bubbling process, which is analogous to the method used by stamping process where ink carries the imprint of the object onto any materials. The fate of the stamping method depends on how strongly the adhesion of EVA coated graphene/Cu with target FTPs. Interestingly, we have found that the thin film of EVA/graphene/Cu can only bind strongly with the FTPs of less than 25 µm in thickness and lower glass transition temperature value to the EVA while wide range of other FTPs are considered upon surface engineering to enhance the binding strength between FTPs and EVA. What’s more, the electrical performance was investigated with a demonstration of triboelectric nanogenerators which confirmed the reliability of graphene transfer onto the FTPs and prospect for the development of flexible and transparent electronics.

The progress of smart skin technology presents unprecedented opportunities for artificial intelligence. Resolution enhancement and energy conservation are critical to improve the perception and standby time of robots. Here, we present a self-powered analogue smart skin for detecting contact location and velocity of the object, based on a single-electrode contact electrification effect and planar electrostatic induction. Using an analogue localizing method, the resolution of this two-dimensional smart skin can be achieved at 1.9 mm with only four terminals, which notably decreases the terminal number of smart skins. The sensitivity of this smart skin is remarkable, which can even perceive the perturbation of a honey bee. Meanwhile, benefiting from the triboelectric mechanism, extra power supply is unnecessary for this smart skin. Therefore, it solves the problems of batteries and connecting wires for smart skins. With microstructured poly(dimethylsiloxane) films and silver nanowire electrodes, it can be covered on the skin with transparency, flexibility, and high sensitivity.

This paper presents a new high-output, flexible and transparent nanogenerator using chemical vapor deposition grown graphene as one of the friction layer. Graphene on copper is transferred onto polyethylene terephthalate by wet transfer method makes graphene-based triboelectric nanogenerator (TENG) have electrical conductivity and high optical transmittance. We have fabricated plasma treated thin layer of polydimethylsiloxane structure as another layer to improve the output performance of nanogenerator. Using this graphene-based TENG, maximum output voltage 650 V and current 12 μA is achieved at 4.3 Hz frequency. As a power source, LCD and 50 commercial blue light-emitting diodes are lighted up. It is low cost, simple, and robust approach for harvesting ambient vibration energy.

A novel roll‐to‐roll, etching‐free, clean transfer of CVD‐grown graphene from copper to plastic using surface‐energy‐assisted delamination in hot deionized water is reported. The delamination process is realized by water penetration between the hydrophobic graphene and a hydrophilic native oxide layer on a copper foil.The transferred graphene on plastic is used as a high‐output flexible and transparent triboelectric nanogenerator.

This paper presents a new high-output, flexible and transparent nanogenerator using CVD grown graphene as one of the friction layer. Graphene on copper is transferred onto PET by wet transfer method, which makes this graphene based TENG have electrical conductivity and high optical transmittance. We have fabricated fluorocarbon plasma treated thin layer of PDMS structure as another friction layer to improve the output performance of nanogenerator. Using this Graphene-based TENG, maximum output voltage 650 V and current 12μA is achieved at 4.3 Hz frequency. As a power source 50 commercial blue LEDs is lighted up. It is low cost, simple and robust approach for harvesting ambient vibration energy.