Yongbao Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yongbao Zhang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Xiang Wu
State Key Laboratory of Geological Processes and Mineral Resources, China University of Geosciences (Wuhan), Wuhan, China
2 shared publications - Jianwu Chen
School of Civil and Resource Engineering, University of Science and Technology Beijing, Beijing 100083, China
1 shared publication - Jingqi Gao
School of Engineering and Technology, China University of Geosciences (Beijing), Beijing 100083, China
1 shared publication - Jinjing Ke
Department of Architecture and Civil Engineering, City University of Hong Kong, Hong Kong 999077, China
1 shared publication - Xiaowei Luo
City Univ. of Hong Kong
1 shared publication - Xun Xv
China Metallurgical Construction Research Institute (Shenzhen) Co., Ltd., Shenzhen 518040, China
1 shared publication
Latest Publications
- Open Access
- 16 August 2020
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 17 (16) , 5948
A Biomechanical Waist Comfort Model for Manual Material Lifting
Low back pain (LBP) is a common disorder that affects the working population worldwide. LBP causes more disability than any other conditions all around the world. Most existing studies focus on the occupational physical factors in association with LBP, while few focus on individual factors, especially the lack of quantitative calculation of waist comfort in biomechanics. Based on the physical statistics of Chinese men, this research used human posture analysis (HPA) to establish the waist strength formula and analyzed the waist strength during a manual material handling. It also explored the influence of weight and height of lifting objects on the L5-S1 spinal load. On this basis, a waist comfort model was proposed in combination with the recommended weight limit (RWL) recommended by NIOSH, and the parameter selection and waist comfort value were verified by Jack simulation software. The results show that pulling force of the Erector Spinae of the waist is closely related to the weight and lifting height of the object. Parameter verification and Jack software simulation results show that the force of L5-S1 is less than 3400 N, which proves that the waist force under this posture is acceptable. The developed waist comfort model can be applied to evaluate work risk, to adjust working intensity and powered exoskeleton design, aiming to decrease the prevalence of LBP.
- 16 August 2020
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 17 (16) , 5948
Open AccessA Biomechanical Waist Comfort Model for Manual Material Lifting
Low back pain (LBP) is a common disorder that affects the working population worldwide. LBP causes more disability than any other conditions all around the world. Most existing studies focus on the occupational physical factors in association with LBP, while few focus on individual factors, especially the lack of quantitative calculation of waist comfort in biomechanics. Based on the physical statistics of Chinese men, this research used human posture analysis (HPA) to establish the waist strength formula and analyzed the waist strength during a manual material handling. It also explored the influence of weight and height of lifting objects on the L5-S1 spinal load. On this basis, a waist comfort model was proposed in combination with the recommended weight limit (RWL) recommended by NIOSH, and the parameter selection and waist comfort value were verified by Jack simulation software. The results show that pulling force of the Erector Spinae of the waist is closely related to the weight and lifting height of the object. Parameter verification and Jack software simulation results show that the force of L5-S1 is less than 3400 N, which proves that the waist force under this posture is acceptable. The developed waist comfort model can be applied to evaluate work risk, to adjust working intensity and powered exoskeleton design, aiming to decrease the prevalence of LBP.
- Open Access
- 7 November 2019
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 16 (22) , 4354
Simulation and Ergonomic Evaluation of Welders’ Standing Posture Using Jack Software
Ergonomics research strives to make workers’ labor more efficient, safer, and more comfortable. Therefore, six digital humans and welding torch model were built and evaluated based on the Jack software in order to improve the ergonomics of welders’ standing postures. Three sets of standing welding actions were designed: walking, raising arm, and contracting arm. Through the Lower Back Analysis, Ovako Working Posture Analysis, Comfort Assessment, and Rapid Upper Limb Assessment, this paper evaluated the optimum range of the weight of the welding torch, the upper limb posture, and the neck posture of the welder. Firstly, the results show that Chinese welders should not use a welding torch with a weight of more than 6 kg when standing up. Secondly, for adult males in the 5th, 50th, 95th percentile of body size, the best operating distance is 321 mm, 371 mm, and 421 mm, respectively, and the best operating height is 1050 mm, 1100 mm, and 1150 mm, respectively; for females in the same percentiles, the optimal operating distance is 271 mm, 321 mm, and 371 mm, respectively, and the optimal operating height is 1000 mm, 1050 mm, and 1100 mm, respectively. Moreover, the horizontal and vertical rotation angle of the welder’s neck should not exceed 15° and 8.7°. The adjustment strategy not only has a positive effect on improving welders’ operational posture and preventing fatigue and injury to the welder, but it also develops research ideas for promoting safety from the perspective of ergonomics.
- 7 November 2019
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 16 (22) , 4354
Open AccessSimulation and Ergonomic Evaluation of Welders’ Standing Posture Using Jack Software
Ergonomics research strives to make workers’ labor more efficient, safer, and more comfortable. Therefore, six digital humans and welding torch model were built and evaluated based on the Jack software in order to improve the ergonomics of welders’ standing postures. Three sets of standing welding actions were designed: walking, raising arm, and contracting arm. Through the Lower Back Analysis, Ovako Working Posture Analysis, Comfort Assessment, and Rapid Upper Limb Assessment, this paper evaluated the optimum range of the weight of the welding torch, the upper limb posture, and the neck posture of the welder. Firstly, the results show that Chinese welders should not use a welding torch with a weight of more than 6 kg when standing up. Secondly, for adult males in the 5th, 50th, 95th percentile of body size, the best operating distance is 321 mm, 371 mm, and 421 mm, respectively, and the best operating height is 1050 mm, 1100 mm, and 1150 mm, respectively; for females in the same percentiles, the optimal operating distance is 271 mm, 321 mm, and 371 mm, respectively, and the optimal operating height is 1000 mm, 1050 mm, and 1100 mm, respectively. Moreover, the horizontal and vertical rotation angle of the welder’s neck should not exceed 15° and 8.7°. The adjustment strategy not only has a positive effect on improving welders’ operational posture and preventing fatigue and injury to the welder, but it also develops research ideas for promoting safety from the perspective of ergonomics.