Takashi Nagao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Takashi Nagao has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Afif Navir Refani
Department of Civil Infrastructure Engineering, Faculty of Vocational, Institut Teknologi Sepuluh Nopember, Surabaya 60111, Indonesia
3 shared publications - Christino Boyke
Department of Marine Transportation Engineering, Faculty of Marine Technology, Institut Teknologi Sepuluh Nopember, Surabaya 60111, Indonesia
3 shared publications - Kenichiro Miyashita
Pacific Consultants Co. Ltd, Japan
2 shared publications - Y. Fukushima
Department of Disaster Mitigation and Facility Maintenance, Eight-Japan Engineering Consultants Inc., Japan
2 shared publications - Daisuke Shibata
Japan Port Consultants, Ltd., Japan
1 shared publication - Hitoshi Aonuma
Kobe University
1 shared publication
Latest Publications
- Open Access
- 4 June 2025
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 15 (3) , 23566-23573
Reproduction Analysis of Pile Lateral Loading Experiments using the Distinct Element Method with Focus on Lateral Spreading Pressure
During a massive earthquake, large-scale lateral spreading may occur in the ground behind mooring facilities. Regarding structures with pile foundations, such as piers, lateral spreading pressure acts on the piles during lateral spreading formation, while the surrounding soil is displaced through the gaps between the piles. Conventional two-dimensional (2D) analysis methods are generally inadequate for capturing such three-dimensional (3D) effects. The present study employs a 3D Distinct Element Method (DEM) to conduct a reproduction analysis of soil displacement and lateral spreading pressure measured during previous lateral loading experiments. The DEM analysis revealed that, as the load was applied, soil particles moved around the surface of the piles, resulting in an uplift at the front of the pile on the loading side and subsidence at the back of the pile. These results closely corresponded to the observed movement of soil particles during the experiments. Due to the differences in the contact conditions between the pile and the surrounding soil before loading, the lateral spreading pressure acting on the lower part of the pile was found to be higher in the analytical results than in the experimental ones. However, the analytical results agreed with the experimental data in terms of the lateral spreading pressure acting on the upper part of the pile.
- 4 June 2025
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 15 (3) , 23566-23573
Open AccessReproduction Analysis of Pile Lateral Loading Experiments using the Distinct Element Method with Focus on Lateral Spreading Pressure
During a massive earthquake, large-scale lateral spreading may occur in the ground behind mooring facilities. Regarding structures with pile foundations, such as piers, lateral spreading pressure acts on the piles during lateral spreading formation, while the surrounding soil is displaced through the gaps between the piles. Conventional two-dimensional (2D) analysis methods are generally inadequate for capturing such three-dimensional (3D) effects. The present study employs a 3D Distinct Element Method (DEM) to conduct a reproduction analysis of soil displacement and lateral spreading pressure measured during previous lateral loading experiments. The DEM analysis revealed that, as the load was applied, soil particles moved around the surface of the piles, resulting in an uplift at the front of the pile on the loading side and subsidence at the back of the pile. These results closely corresponded to the observed movement of soil particles during the experiments. Due to the differences in the contact conditions between the pile and the surrounding soil before loading, the lateral spreading pressure acting on the lower part of the pile was found to be higher in the analytical results than in the experimental ones. However, the analytical results agreed with the experimental data in terms of the lateral spreading pressure acting on the upper part of the pile.
- Open Access
- 8 February 2024
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 14 (1) , 13082-13089
Subgrade Reaction Characteristics to the Anchor Pile of a Sheet Pile Quay Wall
The Conventional Design Method (CDM) for anchored sheet pile quay walls cannot accurately calculate the anchor pile deformation, partly because it does not properly consider the subgrade reaction. This study aims to clarify the subgrade reaction characteristics of the anchor pile using finite element analysis. The CDM assumes that passive failure occurs at the front of the anchor pile. On the contrary, this study shows that the active failure region generated from the back of the sheet pile wall expands to the periphery of the anchor pile and the passive failure region is not generated at its front. Thus, the subgrade reaction to the anchor pile is found to be smaller than the CDM assumption. The CDM also neglects the subgrade reaction in parts shallower than the tie-rod mounting height in the pile front. This study clarifies that the subgrade reaction in this part greatly contributes to the deformation resistance of the pile. Consequently, the subgrade reaction in the shallower range than the tie-rod mounting height is greater than or equal to that in the deeper range. Furthermore, the subgrade reaction has a lower upper limit when acting on the anchor pile than when acting on a horizontally stratified ground, and the difference between these limits widens as the reference earthquake strengthens.
- 8 February 2024
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 14 (1) , 13082-13089
Open AccessSubgrade Reaction Characteristics to the Anchor Pile of a Sheet Pile Quay Wall
The Conventional Design Method (CDM) for anchored sheet pile quay walls cannot accurately calculate the anchor pile deformation, partly because it does not properly consider the subgrade reaction. This study aims to clarify the subgrade reaction characteristics of the anchor pile using finite element analysis. The CDM assumes that passive failure occurs at the front of the anchor pile. On the contrary, this study shows that the active failure region generated from the back of the sheet pile wall expands to the periphery of the anchor pile and the passive failure region is not generated at its front. Thus, the subgrade reaction to the anchor pile is found to be smaller than the CDM assumption. The CDM also neglects the subgrade reaction in parts shallower than the tie-rod mounting height in the pile front. This study clarifies that the subgrade reaction in this part greatly contributes to the deformation resistance of the pile. Consequently, the subgrade reaction in the shallower range than the tie-rod mounting height is greater than or equal to that in the deeper range. Furthermore, the subgrade reaction has a lower upper limit when acting on the anchor pile than when acting on a horizontally stratified ground, and the difference between these limits widens as the reference earthquake strengthens.
- Open Access
- 3 October 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (19) , 10936
Simplified Method for Nonlinear Seismic Response Analysis of Corroded Pile-Supported Wharf
Fiber-based finite element analysis (FB-FEA) has been widely recognized for its ability to reproduce experimental results and is also a reliable method for evaluating the nonlinear seismic response of pile-supported wharves (PSWs). Design practice often employs frame analysis (FA) due to its easy implementation. To precisely reproduce the nonlinear seismic response of PSW using FA, it is necessary to configure mechanical properties such as the hinge property correctly. However, it is unclear whether the hinge properties proposed in previous studies can be applied to PSWs with spun piles. In this study, a novel FA method was developed to investigate the nonlinear seismic response of PSWs with corroded spun piles considering PC bar area reduction, deteriorated material properties, the bending stiffness reduction factor, and the moment–curvature relationship of the spun pile. The nonlinear seismic response of corroded PSWs was determined by performing pushover analysis using three methods: FA using the method of the previous study (FA-1), the proposed FA method (FA-2), and FB-FEA. As regards PSW foundations, vertical pile and batter pile configurations were considered. The pushover analysis results were compared in terms of several parameters, such as the natural period, plastic hinge formation, and load capacity of the corroded PSWs. The FA-2 results agreed very well with the FB-FEA results, while the FA-1 results were less precise with respect to the natural periods and load capacities of corroded PSWs. The results indicated that the bending stiffness reduction factor, moment–curvature relationship, and axial load–bending moment (P–M) capacity of the corroded spun piles should be appropriately defined. Corrosion had greater negative impacts on the compressive axial load and bending moment capacities of the spun pile than on its tensile axial load capacity.
- 3 October 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (19) , 10936
Open AccessSimplified Method for Nonlinear Seismic Response Analysis of Corroded Pile-Supported Wharf
Fiber-based finite element analysis (FB-FEA) has been widely recognized for its ability to reproduce experimental results and is also a reliable method for evaluating the nonlinear seismic response of pile-supported wharves (PSWs). Design practice often employs frame analysis (FA) due to its easy implementation. To precisely reproduce the nonlinear seismic response of PSW using FA, it is necessary to configure mechanical properties such as the hinge property correctly. However, it is unclear whether the hinge properties proposed in previous studies can be applied to PSWs with spun piles. In this study, a novel FA method was developed to investigate the nonlinear seismic response of PSWs with corroded spun piles considering PC bar area reduction, deteriorated material properties, the bending stiffness reduction factor, and the moment–curvature relationship of the spun pile. The nonlinear seismic response of corroded PSWs was determined by performing pushover analysis using three methods: FA using the method of the previous study (FA-1), the proposed FA method (FA-2), and FB-FEA. As regards PSW foundations, vertical pile and batter pile configurations were considered. The pushover analysis results were compared in terms of several parameters, such as the natural period, plastic hinge formation, and load capacity of the corroded PSWs. The FA-2 results agreed very well with the FB-FEA results, while the FA-1 results were less precise with respect to the natural periods and load capacities of corroded PSWs. The results indicated that the bending stiffness reduction factor, moment–curvature relationship, and axial load–bending moment (P–M) capacity of the corroded spun piles should be appropriately defined. Corrosion had greater negative impacts on the compressive axial load and bending moment capacities of the spun pile than on its tensile axial load capacity.
- Open Access
- 2 June 2023
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 13 (3) , 10834-10842
The Impact of Ground Irregular Sedimentary Structure on the Seismic Motion Amplification Characteristics: A case study in Tottori, Japan
The amplification characteristics of seismic motion are determined by the ground structure. In design practice, the ground is assumed to be horizontally stratified. However, the actual ground forms irregular sedimentary structures and the propagation direction of the seismic motion in the soil changes in a complicated way. Thus, the actual amplification factor of seismic motion is dramatically different from the value assumed in design practice. This phenomenon is called the multidimensional effect. The present study targeted at a seismic observation point in Tottori Prefecture, Japan, and estimated the irregular ground structures based on the microtremor observation results. With this ground structure model, Finite Element Analysis (FEA) was conducted and the amplification factors were compared with those determined assuming horizontal stratification. When there is no ground nonlinearity, the multidimensional effect of the ground was more notable in points with thick sedimentary strata, where the peak amplification factor according to the FEA was 1.9 to 3.6 times larger than when horizontal stratification was assumed. In points with thin sedimentary strata, the peak amplification factor ratio was 2.1–2.4. First-order peak frequency was different between cases with irregular ground structures and with horizontal stratification. Furthermore, when the nonlinearity of the ground was evident, the multidimensional effect on the peak amplification factor was not as noticeable as when the ground behaved linearly. The peak magnification ratio due to the multidimensional effect was found to be 2.3. The results of this study show that the amplification characteristics of the seismic motion considered in design practice are likely to be on the dangerous side when the ground is not horizontally stratified.
- 2 June 2023
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 13 (3) , 10834-10842
Open AccessThe Impact of Ground Irregular Sedimentary Structure on the Seismic Motion Amplification Characteristics: A case study in Tottori, Japan
The amplification characteristics of seismic motion are determined by the ground structure. In design practice, the ground is assumed to be horizontally stratified. However, the actual ground forms irregular sedimentary structures and the propagation direction of the seismic motion in the soil changes in a complicated way. Thus, the actual amplification factor of seismic motion is dramatically different from the value assumed in design practice. This phenomenon is called the multidimensional effect. The present study targeted at a seismic observation point in Tottori Prefecture, Japan, and estimated the irregular ground structures based on the microtremor observation results. With this ground structure model, Finite Element Analysis (FEA) was conducted and the amplification factors were compared with those determined assuming horizontal stratification. When there is no ground nonlinearity, the multidimensional effect of the ground was more notable in points with thick sedimentary strata, where the peak amplification factor according to the FEA was 1.9 to 3.6 times larger than when horizontal stratification was assumed. In points with thin sedimentary strata, the peak amplification factor ratio was 2.1–2.4. First-order peak frequency was different between cases with irregular ground structures and with horizontal stratification. Furthermore, when the nonlinearity of the ground was evident, the multidimensional effect on the peak amplification factor was not as noticeable as when the ground behaved linearly. The peak magnification ratio due to the multidimensional effect was found to be 2.3. The results of this study show that the amplification characteristics of the seismic motion considered in design practice are likely to be on the dangerous side when the ground is not horizontally stratified.
- Open Access
- 12 March 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (6) , 3629
Seismic Performance Assessment of Pile-Supported Wharfs: 2D Frame Analysis Method Considering Both Inertial and Kinematic Forces
Frame analysis (FA) is known for its efficiency and low computer resource requirements. However, compared to finite element analysis (FEA), the applicability of FA for the seismic performance assessment of pile-supported wharves (PSWs) is limited, particularly in the ability to account for the kinematic force caused by ground displacement during an earthquake. This study aimed to develop a two-dimensional FA method for PSW seismic response analysis that considers a combination of inertial and kinematic forces. We performed FA and FEA and compared the results. First, we targeted the PSW model without considering the soil slope and discussed the spectral acceleration (SA) evaluation method for calculating inertial force. As a result, an equation for estimating a damping coefficient to evaluate the SA in accordance with the PSW width and natural period was proposed. Next, we targeted the PSW model by considering the soil slope and proposed a method to evaluate the kinematic force based on the amount of ground displacement and the soil spring characteristics. The results revealed that using the proposed method, FA, by considering kinematic and inertial forces, could reproduce the bending moments of the piles comparable to those calculated using FEA. Therefore, solely considering the inertial force for a PSW on a soil slope may cause the bending moment to be underestimated.
- 12 March 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (6) , 3629
Open AccessSeismic Performance Assessment of Pile-Supported Wharfs: 2D Frame Analysis Method Considering Both Inertial and Kinematic Forces
Frame analysis (FA) is known for its efficiency and low computer resource requirements. However, compared to finite element analysis (FEA), the applicability of FA for the seismic performance assessment of pile-supported wharves (PSWs) is limited, particularly in the ability to account for the kinematic force caused by ground displacement during an earthquake. This study aimed to develop a two-dimensional FA method for PSW seismic response analysis that considers a combination of inertial and kinematic forces. We performed FA and FEA and compared the results. First, we targeted the PSW model without considering the soil slope and discussed the spectral acceleration (SA) evaluation method for calculating inertial force. As a result, an equation for estimating a damping coefficient to evaluate the SA in accordance with the PSW width and natural period was proposed. Next, we targeted the PSW model by considering the soil slope and proposed a method to evaluate the kinematic force based on the amount of ground displacement and the soil spring characteristics. The results revealed that using the proposed method, FA, by considering kinematic and inertial forces, could reproduce the bending moments of the piles comparable to those calculated using FEA. Therefore, solely considering the inertial force for a PSW on a soil slope may cause the bending moment to be underestimated.
- Open Access
- 5 February 2023
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 13 (1) , 10108-10115
A Simplified Deformation Estimation Method for Anchor Piles of Sheet Pile Quay Walls under Kinematic Forces during Earthquakes
In the seismic design of quay walls, it is necessary to evaluate the deformation of the walls during earthquakes as well as the safety of structural members. However, conventional seismic design methods for sheet pile quay walls cannot accurately determine the degree of deformation. One reason for this is that conventional methods do not consider kinematic forces acting on an anchor pile due to the deformation of the ground. This study proposes a simplified estimation method for anchor pile deformation under the influence of kinematic forces. The results of two-dimensional finite element analysis reveal that anchor pile deformation involves rotational and translational components caused by the kinematic forces, which the conventional methods do not consider. The deformation of the anchor pile caused by kinematic forces was 30%–40% of the total deformation at the pile head. It was clarified that unlike horizontally stratified ground, shear stress is generated in the ground before an earthquake resulting in the kinematic force acting on the anchor pile during the earthquake. Furthermore, a simplified method for estimating the deformation of the anchor pile under kinematic forces that uses one-dimensional seismic response analysis considering the predicted shear stress based on a theoretical equation is proposed. It was demonstrated that the proposed method accurately reproduces the anchor pile deformation.
- 5 February 2023
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 13 (1) , 10108-10115
Open AccessA Simplified Deformation Estimation Method for Anchor Piles of Sheet Pile Quay Walls under Kinematic Forces during Earthquakes
In the seismic design of quay walls, it is necessary to evaluate the deformation of the walls during earthquakes as well as the safety of structural members. However, conventional seismic design methods for sheet pile quay walls cannot accurately determine the degree of deformation. One reason for this is that conventional methods do not consider kinematic forces acting on an anchor pile due to the deformation of the ground. This study proposes a simplified estimation method for anchor pile deformation under the influence of kinematic forces. The results of two-dimensional finite element analysis reveal that anchor pile deformation involves rotational and translational components caused by the kinematic forces, which the conventional methods do not consider. The deformation of the anchor pile caused by kinematic forces was 30%–40% of the total deformation at the pile head. It was clarified that unlike horizontally stratified ground, shear stress is generated in the ground before an earthquake resulting in the kinematic force acting on the anchor pile during the earthquake. Furthermore, a simplified method for estimating the deformation of the anchor pile under kinematic forces that uses one-dimensional seismic response analysis considering the predicted shear stress based on a theoretical equation is proposed. It was demonstrated that the proposed method accurately reproduces the anchor pile deformation.
- Open Access
- 23 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (3) , 1507
Corrosion Effects on the Mechanical Properties of Spun Pile Materials
Prestressed concrete piles with closed-ended circular hollow sections (spun piles) are sometimes used as foundations for pile-supported wharves. Due to a reduction in the rebar area, concrete compressive strength, yield strength of PC-bar, and bond strength between PC-bar and concrete, corrosion attacks typically lower the performance of spun piles in the marine environment. A comprehensive analysis of the corrosion effect on the mechanical properties of the spun pile materials is crucial to assess the performance of corroded spun plies. Using a three-dimensional finite element analysis (FEA), this study aimed to evaluate the impact of corrosion on the mechanical properties of the material used in spun pile construction. We simulated the effect of nonuniformly distributed corrosion products using a volumetric strain expansion over 0–75 years. The FEA results provided the stress–strain relationship of the corroded spun pile materials and the bond–slip relationship between the corroded PC-bar and concrete. We proposed equations for predicting the deterioration degree of the mechanical properties of corroded spun pile materials and compared them to those presented in previous studies. It was shown that the compressive strength of the corroded cover concrete decreased significantly after the corrosion degree reached 12%, which the previous research had not expected. The bond strength reduction was inverse exponential against the elapsed years after the corrosion degree reached 1.3%. Moreover, the yield strength of PC-bars decreased linearly with the increase in the corrosion degree.
- 23 January 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (3) , 1507
Open AccessCorrosion Effects on the Mechanical Properties of Spun Pile Materials
Prestressed concrete piles with closed-ended circular hollow sections (spun piles) are sometimes used as foundations for pile-supported wharves. Due to a reduction in the rebar area, concrete compressive strength, yield strength of PC-bar, and bond strength between PC-bar and concrete, corrosion attacks typically lower the performance of spun piles in the marine environment. A comprehensive analysis of the corrosion effect on the mechanical properties of the spun pile materials is crucial to assess the performance of corroded spun plies. Using a three-dimensional finite element analysis (FEA), this study aimed to evaluate the impact of corrosion on the mechanical properties of the material used in spun pile construction. We simulated the effect of nonuniformly distributed corrosion products using a volumetric strain expansion over 0–75 years. The FEA results provided the stress–strain relationship of the corroded spun pile materials and the bond–slip relationship between the corroded PC-bar and concrete. We proposed equations for predicting the deterioration degree of the mechanical properties of corroded spun pile materials and compared them to those presented in previous studies. It was shown that the compressive strength of the corroded cover concrete decreased significantly after the corrosion degree reached 12%, which the previous research had not expected. The bond strength reduction was inverse exponential against the elapsed years after the corrosion degree reached 1.3%. Moreover, the yield strength of PC-bars decreased linearly with the increase in the corrosion degree.
- Open Access
- 19 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (14) , 7266
Seismic Performance Assessment of Wide Pile-Supported Wharf Considering Soil Slope and Waveform Duration
Pile-supported wharf (PSW) is one of the primary port structures and is often damaged by earthquakes. To mitigate the risk of seismic damage to a PSW, its seismic performance should be thoroughly assessed. This study aimed to examine the impact of ground displacement on the seismic performance of PSW with a mild soil slope. We performed soil-structure system finite element analysis targeting a wide PSW. The analysis is divided into two scenarios. In the first scenario, the PSW was modeled without regard for the soil slope, whereas the second scenario considered the soil slope. Two waveforms that matched the target spectral acceleration were used to study the effects of the waveform duration on the seismic response of PSW. The analysis results revealed substantial influences of soil slope displacement as well as differences in waveforms on PSW’s seismic performance.
- 19 July 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (14) , 7266
Open AccessSeismic Performance Assessment of Wide Pile-Supported Wharf Considering Soil Slope and Waveform Duration
Pile-supported wharf (PSW) is one of the primary port structures and is often damaged by earthquakes. To mitigate the risk of seismic damage to a PSW, its seismic performance should be thoroughly assessed. This study aimed to examine the impact of ground displacement on the seismic performance of PSW with a mild soil slope. We performed soil-structure system finite element analysis targeting a wide PSW. The analysis is divided into two scenarios. In the first scenario, the PSW was modeled without regard for the soil slope, whereas the second scenario considered the soil slope. Two waveforms that matched the target spectral acceleration were used to study the effects of the waveform duration on the seismic response of PSW. The analysis results revealed substantial influences of soil slope displacement as well as differences in waveforms on PSW’s seismic performance.
- Open Access
- 14 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (4) , 1963
Site-Specific Earthquake Ground Motions for Seismic Design of Port Facilities in Indonesia
In Indonesia, infrastructure, such as port facilities, has been damaged by earthquakes. Therefore, evaluating rational earthquake ground motions (EGMs) for seismic design is necessary to mitigate earthquake disasters in the future. The EGMs in the Indonesian Seismic Code are stipulated based on the ASCE standards and not on site-specific ones. This study aims to propose site-specific EGMs for the seismic design of port facilities in Indonesia. The EGM records and ground data in Indonesia were used for analysis. The EGM incidents in the bedrock were evaluated with deconvolution analysis. The obtained EGMs were amplitude-adjusted to peak ground acceleration similar to that of the EGMs in the bedrock in the Indonesian Seismic Code. A seismic response analysis considering nonlinear soil characteristics was conducted, and 144 EGMs at port sites were obtained. Considering the variation in the obtained EGMs, we propose site-specific EGMs for the seismic design of port facilities. A comparison of the proposed EGMs with those in the design code reveals that the difference between them is significant.
- 14 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (4) , 1963
Open AccessSite-Specific Earthquake Ground Motions for Seismic Design of Port Facilities in Indonesia
In Indonesia, infrastructure, such as port facilities, has been damaged by earthquakes. Therefore, evaluating rational earthquake ground motions (EGMs) for seismic design is necessary to mitigate earthquake disasters in the future. The EGMs in the Indonesian Seismic Code are stipulated based on the ASCE standards and not on site-specific ones. This study aims to propose site-specific EGMs for the seismic design of port facilities in Indonesia. The EGM records and ground data in Indonesia were used for analysis. The EGM incidents in the bedrock were evaluated with deconvolution analysis. The obtained EGMs were amplitude-adjusted to peak ground acceleration similar to that of the EGMs in the bedrock in the Indonesian Seismic Code. A seismic response analysis considering nonlinear soil characteristics was conducted, and 144 EGMs at port sites were obtained. Considering the variation in the obtained EGMs, we propose site-specific EGMs for the seismic design of port facilities. A comparison of the proposed EGMs with those in the design code reveals that the difference between them is significant.
- Open Access
- 11 April 2021
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 11 (2) , 6873-6881
Maximum Credible Earthquake Ground Motions with Focus on Site Amplification due to Deep Subsurface
Since an Earthquake Ground Motion (EGM) is amplified from the propagation through the ground, different models are required for each ground type in the seismic design of structures. While the shallow subsurface indicators are used for the classification of ground types, a deep subsurface has a significant impact on the amplification of the EGMs. This study discusses the maximum credible EGMs for seismic design reflecting seismic amplification due to deep subsurface. The design spectra, reflecting the site amplification factor of the target location, are presented by the calculation of the EGMs with the same source and path characteristics and different site amplification factors as recent major Japanese earthquake records have shown, from the perspective of establishing the maximum credible EGMs that may occur in the future at a target site. The present design spectra, which are based on the natural period of a shallow subsurface, are compared with those based on the site amplification factors, considering the effect of deep subsurfaces. Although there are almost no differences in the design spectra with the present design methods according to the surface ground type, the proposed method provides significantly different design spectra for each site amplification factor.
- 11 April 2021
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 11 (2) , 6873-6881
Open AccessMaximum Credible Earthquake Ground Motions with Focus on Site Amplification due to Deep Subsurface
Since an Earthquake Ground Motion (EGM) is amplified from the propagation through the ground, different models are required for each ground type in the seismic design of structures. While the shallow subsurface indicators are used for the classification of ground types, a deep subsurface has a significant impact on the amplification of the EGMs. This study discusses the maximum credible EGMs for seismic design reflecting seismic amplification due to deep subsurface. The design spectra, reflecting the site amplification factor of the target location, are presented by the calculation of the EGMs with the same source and path characteristics and different site amplification factors as recent major Japanese earthquake records have shown, from the perspective of establishing the maximum credible EGMs that may occur in the future at a target site. The present design spectra, which are based on the natural period of a shallow subsurface, are compared with those based on the site amplification factors, considering the effect of deep subsurfaces. Although there are almost no differences in the design spectra with the present design methods according to the surface ground type, the proposed method provides significantly different design spectra for each site amplification factor.