MMMohammad Malekmohammad

Mohammad Malekmohammad

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mohammad Malekmohammad has a total of 43 co-authors. Here are the top co-authors by number of shared publications:

  • Reza Asadi

    Malek Ashtar University, Department of Electronics, Shabanloo Street, Lavizan, Tehran, Tehran Province, Iran

    5 shared publications
  • Mahmood Soltanolkotabi

    Department of Physics, Faculty of Science, University of Isfahan, Isfahan, Iran

    4 shared publications
  • R. Asadi

    3 shared publications
  • A. Erfanian

    Electronics Research Center, Malek ashtar University of Technology, Tehran, Iran

    2 shared publications
  • Ali Hatef

    Nipissing Computational Physics Laboratory (NCPL), Department of Computer Science and Mathematics, Nipissing University, North Bay, Ontario P1B 8L7, Canada

    2 shared publications
  • M. Khaje

    Department of Electrical Engineering, K.N. Toosi university of Technology, Seyyed Khandan Bridge, Tehran, Iran

    2 shared publications

Latest Publications

  • External pumped all-optical microfiber modulator based on reduced graphene oxide

    by Elaheh Zamani, Mohammad Malekmohammad, Afrouz Taherian

    In this research, first, the Z-scan technique is used to measure the nonlinear optical properties of reduced graphene oxide (rGO) to indicate the high nonlinear coefficients. Second, a novel, to the best of our knowledge, vertically pumped, all-optical modulator is produced based on a rGO-coated multimode optical microfiber. The effect of the microfiber curvature, microfiber diameter, and substrate materials is investigated and optimized. Also, a simula-tion based on the finite-difference time-domain (FDTD) method is performed. The modulation depth increased to 4.2 dB by the external low-power ultraviolet pump laser (300 mW) for modulators based on the multimode microfibers. The presented process is a simple, cost-effective route to fabricate, and it is easy to use the device.(c) 2023 Optica Publishing Group


  • Open Access

    The Design and Simulation of a Coarse-to-Fine Optical MEMS Accelerometer

    by Mojtaba Rahimi, Majid Taghavi, Mohammad Malekmohammad

    In this paper, a novel coarse-to-fine optical MEMS accelerometer based on the Fabry Perot (FP) interferometer is proposed. The mechanical structure consists of a proof mass that is suspended by four L-shaped springs. The deflection of the proof mass due to the applied acceleration is detected using two FP cavities which comprise the optical system of the device. Using coarse-to-fine measurement and the dual-wavelength method increases the sensitivity of the accelerometer as well as the linear measurement range simultaneously. The optical simulation shows that the sensitivity of the proposed device is 10 times as high as that of a similar optical MEMS accelerometer with one FP cavity. In addition, the proposed optical system is insensitive to the displacements of the proof mass in orthogonal directions as a result of which cross-axis sensitivity is considerably reduced. The minimum feature size of the structure is 15 um and the optical signal is conducted completely through the optical fibers, facilitating the fabrication of the device. The simulation results are as follows: mechanical sensitivity of 190 nm/g, optical sensitivity of 8 nm/g, linear measurement of 5 g, and first resonance frequency of 1141 Hz.

  • Open Access

    Wide-angle broadband antireflection coatings based on boomerang-like alumina nanostructures in visible region

    by MirKazem Omrani, Mohammad Malekmohammad, Hosein Zabolian

    A novel boomerang-like alumina based antireflective coating with ultra-low reflectance has been produced for light incidence angles form 0 up to 45°. Boomerang-like alumina nanostructures have been fabricated on the BK7 glass substrates by dip-coating and surface modification via hot water treatment. To achieve the lowest residual reflectance, the effect of dip-coating rate and hot-water temperature in the treatment process has been investigated and optimized. To further investigate the boomerang-like alumina nanostructure and extract its graded refractive index profile by fitting the measured reflectance spectrum with the simulated one, a simulation based on the finite-difference time-domain (FDTD) method has been performed. The average reflectance measured at normal incidence for double-sided coated BK7 glass substrates is only 0.3% in the visible spectral region. Considering both sides, the average reflectance of the substrate decreased in the spectral range of 400–700 nm down to 0.4% at incidence angles of 45° by applying the boomerang-like alumina antireflection coatings. The optimized single layer boomerang-like alumina coating on the curved aspheric lens exhibited a low average reflectance of less than 0.14% and an average transmittance of above 99.3% at normal incidence. The presented process is a simple and cost-effective route towards broadband and omnidirectional antireflection coatings, which have promising potential to be applied on substrates having large scales with complex geometric shapes.


  • Coarse-to-fine optical MEMS accelerometer design and simulation

    by Mojtaba Rahimi, Majid Taghavi, Mohammad Malekmohammad

    A coarse-to-fine optical microelectromechanical systems (MEMS) accelerometer based on the Fabry-Perot (FP) interferometer is proposed. The mechanical structure consists of a proof mass that is suspended by four L-shaped springs. The deflection of the proof mass due to the applied acceleration is detected using two FP cavities that comprise the system's optical system. Using coarse-to-fine measurement and the dual wavelength method simultaneously increases the sensitivity of the accelerometer as well as the linear measurement range. The optical simulation shows that the sensitivity of the proposed device is 10 times as high as that of a similar optical MEMS accelerometer with one FP cavity. In addition, the proposed optical system is insensitive to the displacements of the proof mass in the orthogonal directions, which considerably reduced the cross-axis sensitivity. The minimum feature size of the structure is 15 mu m and the optical signal is conducted completely through the optical fibers, facilitating the device fabrication. Here are the results of the simulation: mechanical sensitivity of 190 nm/g, optical sensitivity of 8 nm/g, linear measurement of +/- 5 g, and first resonance frequency of 1141 Hz. (C) 2022 Optical Society of America


  • Direct and Plasmonic Nanoparticle‐Mediated Infrared Neural Stimulation: Comprehensive Computational Modeling and Validation

    by Zahra Ebtehaj, Mohammad Malekmohammad, Ali Hatef, Mahmood Soltanolkotabi

    Infrared neural stimulation techniques have potential applications in the diagnosis and treatment of numerous neurological and psychiatric disorders. There has been little progress in the computational modeling of these techniques and further improvement is needed in this area. In this paper, a comprehensive computational model is presented for simulating the complete mechanism of direct and plasmonic nanoparticle‐mediated infrared neural stimulation techniques in schematic samples of experimental setups. The simulation process involves three phases: 1) Simulating the light transmission and absorption in setups containing pure water or a gold nanorod solution using developed 3D, time‐independent, and time‐dependent Monte Carlo models, 2) calculating the spatiotemporal evolutions of temperature within the setup using the finite difference method and a presented novel method, and 3) simulating the thermally induced responses of lipid membranes using an improved method compared to existing theoretical models. The model is validated by comparing the computational results with existing experimental data. The effect of the laser pulse characteristics, nanofluid properties, and some other related parameters on the thermally induced membrane responses is investigated. The computational results help to optimize the parameters selection and maximize the overall efficiency of the infrared neural stimulation techniques.


  • Fabrication of a broadband anti-reflection layer using metal-assisted chemical etching

    by Fatemeh Malekmohammad, Mohammad Malekmohammad

    In this paper, an easy and cost-efficient method to create a single anti-reflective layer on a silicon substrate is presented. In this experiment, by using the silver nanoparticles on a silicon substrate at room temperature, a porous nanostructure is created. This nanostructure significantly reduces the reflection and increases the transmission in a wide spectral range. By using this method, a porous layer on one side of the silicon substrate is fabricated. The results show that the reflection reduces to 31% and the transmission increases to 68% in the 3500–5000 nm spectral range, and these values are close to the reflection and transmission of a sample with ideal one-sided anti-reflection.


  • Design of high-efficiency small-size passive all-optical diodes based on photonic crystal and graphene

    by Mozhde Janfada, Mohammad Malekmohammad, Mahmood Soltanolkotabi

    Light propagation in an asymmetric multilayered structure composed of a linear defective photonic crystal and nonlinear graphene layer is theoretically investigated. A (BA)4/graphene/(AB)4(AABB)4 structure with a slight perturbation in the (AABB)4 part can provide non-reciprocal transmission to achieve an optical diode. This structure was optimized in order to have a low-operation input intensity, high-contrast, small-size all-optical diode without an additional pump signal. In this work, four different passive all-optical diodes are presented. The best contrast ratio is 6.3, and the minimum operation input intensity for diode action is 2.7×10−3  MWcm2. This structure gives an all-optical diode with a smaller size and higher efficiency in comparison to previous works.


  • The effect of second phase particles on light transmission of ZnS/diamond nanocomposite

    by Elmira Karimzadeh, Mohammad Hossein Enayati, Mohammad Malekmohammad, Hamidreza Fallah, Amir Alhaji

    The effect of second phase size (200, 400, 600 and 800 nm) and volume fraction (10, 20 and 30%) on light transmission behavior of ZnS/diamond composite was simulated using Mie theory and FDTD method. It is expected that the results of FDTD method to be close to experimental results. To validate this approach, simulation results of Mie theory and FDTD method were compared with experimental light transmission (T) of 88.7-11.3 vol% ZnS/diamond composite, reported previously by Xue and et al, and it is shown that results of FDTD method matched well with these experimental results. Because of considering particles interaction and the higher accuracy of the FDTD method in calculating the scattering cross section than the Mie theory, the difference between simulation curves of ZnS/diamond nanocomposite based on Mie theory and FDTD method became more significant with increasing second phase size particularly at greater volume fractions and at short wavelengths. Simulated light transmission curves obtained by FDTD method showed that the optimized second phase size should be smaller than 800 nm for volume fraction of 10% and smaller than 200 nm for volume fractions of 20 and 30%. On the other words, within these sizes, the reduction of light transmission of ZnS/diamond composite compared to monolithic ZnS is lower than 10%.


  • Computational Modeling and Validation of Thermally Induced Electrical Capacitance Changes for Lipid Bilayer Membranes Irradiated by Pulsed Lasers

    by Zahra Ebtehaj, Ali Hatef, Mohammad Malekmohammad, Mahmood Soltanolkotabi

    Neural stimulation has widespread applications in investigating brain functions, restoring impaired neural functions and treating numerous neurological/psychiatric diseases. Using infrared pulses to stimulate neurons (Infrared Neural Stimulation, INS) offers a direct and noninvasive technique. Recent research has demonstrated that transient heating associated with the absorption of infrared light by the local aqueous medium around the cell membrane can stimulate nerves. One mechanism for this stimulation is due to a thermally induced increase in the membrane electrical capacitance which causes cell depolarization as well as action potential production under certain physiological conditions. A theoretical and computational model helps to better understand the mechanism of thermally induced electrical capacitance changes and to optimize the stimulus parameters. In this paper, we develop the existing theoretical models for membrane electrical capacitance and its thermally induced changes. We improve the formulation of Gouy-Chapman-Stern theory by Genet et al. and Shapiro et al. with the addition of the diffuse layer to the electrical double layer and by modifying the relation of Stern layer capacitance, to calculate the membrane capacitive charge and capacitive current. We also present a new method to calculate the membrane electrical capacitance and the rate of its thermally induced changes. In our calculations, two new factors are considered including the temperature dependence of the intrinsic surface charge density and the hydrophobic core dielectric constant of the lipid bilayer. Our developed model predicts a rate of 0.3%°C and 0.26%°C for the thermally induced capacitance changes of the artificial lipid bilayer under two different sets of conditions previously reported by Shapiro et al. and Carvalho-de-Souza et al., respectively. Our model is in very good agreement with the corresponding experimental values given by these groups. The presented model is also able to calculate the membrane capacitive currents and investigate the voltage dependence of this current.