Felix M. Mayor
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Felix M. Mayor has a total of 84 co-authors. Here are the top co-authors by number of shared publications:
- Amir H. Safavi-Naeini
Department of Applied Physics and Ginzton Laboratory, Stanford University, Stanford, USA
15 shared publications - Wentao Jiang
Stanford University
12 shared publications Amir H. Safavi-Naeini
Stanford University
6 shared publications- Christopher J. Sarabalis
Department of Applied Physics and Ginzton Laboratory, Stanford University, 348 Via Pueblo Mall, Stanford, California 94305, USA
5 shared publications Wentao Jiang
Department of Applied Physics and Ginzton Laboratory, Stanford University, Stanford, USA
5 shared publications- Samuel Gyger
Department of Applied Physics and Ginzton Laboratory, Stanford University , 348 Via Pueblo Mall, Stanford, California 94305
4 shared publications
Latest Publications
- 14 April 2026
- Published by Springer Nature in Nature Physics
- Vol. 22 (10) , 1646-1654
Intrinsic phononic dressed states in a nanomechanical system
- 14 April 2026
- Published by Springer Nature in Nature Physics
- Vol. 22 (10) , 1646-1654
Intrinsic phononic dressed states in a nanomechanical system
- 6 April 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (14)
Robotic chip-scale nanofabrication for superior consistency
Unlike the rigid, high-volume automation found in industry, academic research requires process flexibility that has historically relied on variable manual operations. This hinders the fabrication of advanced, complex devices. We propose to address this gap by automating these low-volume, high-stakes tasks using a robotic arm to improve process control and consistency. As a proof of concept, we deploy this system for the resist development of Josephson junction devices. A statistical comparison of the process repeatability shows that the robotic process achieves a resistance spread across chips close to 2%, a significant improvement over the ∼7% spread observed from human operators, validating robotics as a solution to eliminate operator-dependent variability and providing a path toward industrial-level consistency in a research setting.
- 6 April 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (14)
Robotic chip-scale nanofabrication for superior consistency
Unlike the rigid, high-volume automation found in industry, academic research requires process flexibility that has historically relied on variable manual operations. This hinders the fabrication of advanced, complex devices. We propose to address this gap by automating these low-volume, high-stakes tasks using a robotic arm to improve process control and consistency. As a proof of concept, we deploy this system for the resist development of Josephson junction devices. A statistical comparison of the process repeatability shows that the robotic process achieves a resistance spread across chips close to 2%, a significant improvement over the ∼7% spread observed from human operators, validating robotics as a solution to eliminate operator-dependent variability and providing a path toward industrial-level consistency in a research setting.
- 2 February 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 25 (2)
Correlated dephasing in a piezoelectrically transduced silicon phononic waveguide
- 2 February 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 25 (2)
Correlated dephasing in a piezoelectrically transduced silicon phononic waveguide
- Open Access
Robotic chip-scale nanofabrication for superior consistency
Unlike the rigid, high-volume automation found in industry, academic research requires process flexibility that has historically relied on variable manual operations. This hinders the fabrication of advanced, complex devices. We propose to address this gap by automating these low-volume, high-stakes tasks using a robotic arm to improve process control and consistency. As a proof of concept, we deploy this system for the resist development of Josephson junction devices. A statistical comparison of the process repeatability shows the robotic process achieves a resistance spread across chips close to 2%, a significant improvement over the ~7% spread observed from human operators, validating robotics as a solution to eliminate operator-dependent variability and a path towards industrial-level consistency in a research setting.
Open AccessRobotic chip-scale nanofabrication for superior consistency
Unlike the rigid, high-volume automation found in industry, academic research requires process flexibility that has historically relied on variable manual operations. This hinders the fabrication of advanced, complex devices. We propose to address this gap by automating these low-volume, high-stakes tasks using a robotic arm to improve process control and consistency. As a proof of concept, we deploy this system for the resist development of Josephson junction devices. A statistical comparison of the process repeatability shows the robotic process achieves a resistance spread across chips close to 2%, a significant improvement over the ~7% spread observed from human operators, validating robotics as a solution to eliminate operator-dependent variability and a path towards industrial-level consistency in a research setting.
- 22 October 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 24 (4)
Spectral diffusion of nanomechanical resonators due to single quantum defects
- 22 October 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 24 (4)
Spectral diffusion of nanomechanical resonators due to single quantum defects
- 13 October 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (15)
Integrated phononic waveguide on thin-film lithium niobate on diamond
We demonstrate wavelength-scale phononic waveguides formed by transfer-printed thin-film lithium niobate (LN) on bulk diamond, a material stack that combines the strong piezoelectricity of LN with the high acoustic velocity and color-center compatibility of diamond. We characterize a delay line based on a 100 μm long phononic waveguide at room and cryogenic temperatures. The total insertion loss through the device at 4 K is −5.8 dB, corresponding to a >50 % transducer efficiency, at a frequency of 2.8 GHz. Our work represents a step toward phonon-mediated hybrid quantum systems consisting of strain-sensitive color centers in diamond.
- 13 October 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (15)
Integrated phononic waveguide on thin-film lithium niobate on diamond
We demonstrate wavelength-scale phononic waveguides formed by transfer-printed thin-film lithium niobate (LN) on bulk diamond, a material stack that combines the strong piezoelectricity of LN with the high acoustic velocity and color-center compatibility of diamond. We characterize a delay line based on a 100 μm long phononic waveguide at room and cryogenic temperatures. The total insertion loss through the device at 4 K is −5.8 dB, corresponding to a >50 % transducer efficiency, at a frequency of 2.8 GHz. Our work represents a step toward phonon-mediated hybrid quantum systems consisting of strain-sensitive color centers in diamond.
- Open Access
- 15 March 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-7
High photon-phonon pair generation rate in a two-dimensional optomechanical crystal
Integrated optomechanical systems are a leading platform for manipulating, sensing, and distributing quantum information, but are limited by residual optical heating. Here, we demonstrate a two-dimensional optomechanical crystal (OMC) geometry with increased thermal anchoring and a mechanical mode at 7.4 GHz, well aligned with the operation range of cryogenic microwave hardware and piezoelectric transducers. The eight times better thermalization than current one-dimensional OMCs, large optomechanical coupling rates, g 0/2π ≈ 880 kHz, and high optical quality factors, Q opt = 2.4 × 105, allow ground-state cooling (n m = 0.32) of the acoustic mode from 3 K and entering the optomechanical strong-coupling regime. In pulsed sideband asymmetry measurements, we show ground-state operation (n m < 0.45) at temperatures below 10 mK, with repetition rates up to 3 MHz, generating photon-phonon pairs at ≈ 147 kHz. Our results extend optomechanical system capabilities and establish a robust foundation for future microwave-to-optical transducers with entanglement rates exceeding state-of-the-art superconducting qubit decoherence rates.
- 15 March 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-7
Open AccessHigh photon-phonon pair generation rate in a two-dimensional optomechanical crystal
Integrated optomechanical systems are a leading platform for manipulating, sensing, and distributing quantum information, but are limited by residual optical heating. Here, we demonstrate a two-dimensional optomechanical crystal (OMC) geometry with increased thermal anchoring and a mechanical mode at 7.4 GHz, well aligned with the operation range of cryogenic microwave hardware and piezoelectric transducers. The eight times better thermalization than current one-dimensional OMCs, large optomechanical coupling rates, g 0/2π ≈ 880 kHz, and high optical quality factors, Q opt = 2.4 × 105, allow ground-state cooling (n m = 0.32) of the acoustic mode from 3 K and entering the optomechanical strong-coupling regime. In pulsed sideband asymmetry measurements, we show ground-state operation (n m < 0.45) at temperatures below 10 mK, with repetition rates up to 3 MHz, generating photon-phonon pairs at ≈ 147 kHz. Our results extend optomechanical system capabilities and establish a robust foundation for future microwave-to-optical transducers with entanglement rates exceeding state-of-the-art superconducting qubit decoherence rates.
- Top Cited PapersOpen Access
- 15 March 2024
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 10 (11) , eadl1814
Single-mode squeezed-light generation and tomography with an integrated optical parametric oscillator
Quantum optical technologies promise advances in sensing, computing, and communication. A key resource is squeezed light, where quantum noise is redistributed between optical quadratures. We introduce a monolithic, chip-scale platform that exploits the χ (2) nonlinearity of a thin-film lithium niobate (TFLN) resonator device to efficiently generate squeezed states of light. Our system integrates all essential components—except for the laser and two detectors—on a single chip with an area of one square centimeter, reducing the size, operational complexity, and power consumption associated with conventional setups. Using the balanced homodyne measurement subsystem that we implemented on the same chip, we measure a squeezing of 0.55 decibels and an anti-squeezing of 1.55 decibels. We use 20 milliwatts of input power to generate the parametric oscillator pump field by using second harmonic generation on the same chip. Our work represents a step toward compact and efficient quantum optical systems posed to leverage the rapid advances in integrated nonlinear and quantum photonics.
- 15 March 2024
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 10 (11) , eadl1814
Top Cited PapersOpen AccessSingle-mode squeezed-light generation and tomography with an integrated optical parametric oscillator
Quantum optical technologies promise advances in sensing, computing, and communication. A key resource is squeezed light, where quantum noise is redistributed between optical quadratures. We introduce a monolithic, chip-scale platform that exploits the χ (2) nonlinearity of a thin-film lithium niobate (TFLN) resonator device to efficiently generate squeezed states of light. Our system integrates all essential components—except for the laser and two detectors—on a single chip with an area of one square centimeter, reducing the size, operational complexity, and power consumption associated with conventional setups. Using the balanced homodyne measurement subsystem that we implemented on the same chip, we measure a squeezing of 0.55 decibels and an anti-squeezing of 1.55 decibels. We use 20 milliwatts of input power to generate the parametric oscillator pump field by using second harmonic generation on the same chip. Our work represents a step toward compact and efficient quantum optical systems posed to leverage the rapid advances in integrated nonlinear and quantum photonics.
- 1 January 2024
- Published by Optica Publishing Group
- p. QTu4A.4
A microwave-to-optical transducer based on a two-dimensional optomechanical crystal
Microwave-to-optical frequency converters have been plagued by added noise caused by heating from the pump laser. We present our efforts on mitigating this heating by implementing a piezo-optomechanical transducer based on a two-dimensional optome-chanical crystal.
- 1 January 2024
- Published by Optica Publishing Group
- p. QTu4A.4
A microwave-to-optical transducer based on a two-dimensional optomechanical crystal
Microwave-to-optical frequency converters have been plagued by added noise caused by heating from the pump laser. We present our efforts on mitigating this heating by implementing a piezo-optomechanical transducer based on a two-dimensional optome-chanical crystal.
- Open Access
- 12 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Tunable dual wavelength laser on thin film lithium niobate
We experimentally demonstrate a tunable dual wavelength laser on thin film lithium niobate. By combining a micro-transfer printed amplifier with a Vernier cavity containing a periodically poled region, we realize a tunable laser in the telecom band and partially convert it to its second harmonic.
- 12 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Open AccessTunable dual wavelength laser on thin film lithium niobate
We experimentally demonstrate a tunable dual wavelength laser on thin film lithium niobate. By combining a micro-transfer printed amplifier with a Vernier cavity containing a periodically poled region, we realize a tunable laser in the telecom band and partially convert it to its second harmonic.