Elad Chakotay
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Elad Chakotay has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
A. Bussiba
Materials Department, Nuclear Research Center Negev
1 shared publicationA. Stern
Department of Materials Engineering, Ben-Gurion University of the Negev
1 shared publication- Arie Busiba
Department of Materials Engineering, Ben Gurion University of the Negev, Beer Sheva 84105, Israel
1 shared publication I. Alon
Materials Department, Nuclear Research Center Negev
1 shared publication- Igal Alon
Nuclear Research Center Negev (NRCN), P.O. Box 9001, Beer Sheva 84190, Israel
1 shared publication M. Pinkas
Materials Department, Nuclear Research Center Negev
1 shared publication
Latest Publications
- Open Access
Effects of Anisotropic Microstructure and Load Ratio on Fatigue Crack Propagation Rate in Additively Manufactured Ti-6Al-4V Alloy
Additive manufacturing (AM) refers to advanced technologies for building 3D objects by adding material layer upon layer using either electron beam melting (EBM) or selective laser melting. AM allows us to produce lighter and more complex parts. However, various defects are created during the AM process, which severely affect fatigue behavior. In the current research, the effects of the anisotropic microstructure in the in-plane and out-of-plane orientations and defects on the fatigue crack propagation rate (FCPR) and crack path were studied. A resonance machine was used to determine the fatigue crack propagation rate (da/dN vs. ΔK) from the near-threshold up to the final fracture, accompanied by in situ Acoustic Emission (AE) monitoring. Micro-Computerized Tomography (µCT) enabled us to characterize surface and microstructural defects. Metallography was used to determine the microstructure vs. orientations and fractography to classify the fatigue fracture propagation modes. Calculations of the local stress distribution were performed to determine the interactions of the cracks with the defects. In the out-of-plane direction, the material exhibited high fatigue fracture toughness accompanied by a slightly lower fatigue crack propagation rate as compared to in-plane orientations. The near-threshold stress intensity factor was slightly higher in the out-of-plane orientation as compared to that in the in-plane one, accompanied by a lower exponent of the Paris law regime. The threshold decreased with an increasing load ratio as expected for both orientations. The crack propagation direction that crosses the elongated grains plays an important role in increasing fatigue resistance in the out-of-plane direction. In the in-plane directions, the crack propagates parallel to the grain boundary, interacts with more defects and exhibits more brittle striations on the fracture surface, resulting in lower fatigue resistance.
Open AccessEffects of Anisotropic Microstructure and Load Ratio on Fatigue Crack Propagation Rate in Additively Manufactured Ti-6Al-4V Alloy
Additive manufacturing (AM) refers to advanced technologies for building 3D objects by adding material layer upon layer using either electron beam melting (EBM) or selective laser melting. AM allows us to produce lighter and more complex parts. However, various defects are created during the AM process, which severely affect fatigue behavior. In the current research, the effects of the anisotropic microstructure in the in-plane and out-of-plane orientations and defects on the fatigue crack propagation rate (FCPR) and crack path were studied. A resonance machine was used to determine the fatigue crack propagation rate (da/dN vs. ΔK) from the near-threshold up to the final fracture, accompanied by in situ Acoustic Emission (AE) monitoring. Micro-Computerized Tomography (µCT) enabled us to characterize surface and microstructural defects. Metallography was used to determine the microstructure vs. orientations and fractography to classify the fatigue fracture propagation modes. Calculations of the local stress distribution were performed to determine the interactions of the cracks with the defects. In the out-of-plane direction, the material exhibited high fatigue fracture toughness accompanied by a slightly lower fatigue crack propagation rate as compared to in-plane orientations. The near-threshold stress intensity factor was slightly higher in the out-of-plane orientation as compared to that in the in-plane one, accompanied by a lower exponent of the Paris law regime. The threshold decreased with an increasing load ratio as expected for both orientations. The crack propagation direction that crosses the elongated grains plays an important role in increasing fatigue resistance in the out-of-plane direction. In the in-plane directions, the crack propagates parallel to the grain boundary, interacts with more defects and exhibits more brittle striations on the fracture surface, resulting in lower fatigue resistance.
- Open Access
- 28 December 2018
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 29, 33-40
Dynamic Versus Quasi Static Fracture Toughness of Additively Manufactured AlSi10Mg Alloy by Selective Laser Melting Technique
In today's additive manufacturing sector, one of the most popular areas is selective laser melting (SLM) due to its capability of producing geometrically complex metal parts directly from CAD model in a few short steps. Many studies have been reported on static mechanical properties of SLM components; however, dynamic properties of SLM components of different materials have not been thoroughly investigated. Only few papers have been published on the dynamic mechanical behavior, especially in the crack resistance of selective laser melted AlSi10Mg alloy. In the present study, the effect of loading rate, dynamic versus quasi static, on the fracture toughness of the as-built alloy (X and Z orientations) has been investigated. The experimental results revealed the inherently anisotropic behavior for loading rates where the Z orientation exhibited lower toughness compared to the x orientation. The dynamic loading by impact, resulted in a significant decrease of the toughness values up to about 50% compared to the quasi-static loading. This mechanical response was attributed to the increase in the yield stress which alters the state stress at the crack tip from the planestress to some extent of the mix-mode plane stress/strain.
- 28 December 2018
- Published by Universitatea Dunarea de Jos din Galati in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
- Vol. 29, 33-40
Open AccessDynamic Versus Quasi Static Fracture Toughness of Additively Manufactured AlSi10Mg Alloy by Selective Laser Melting Technique
In today's additive manufacturing sector, one of the most popular areas is selective laser melting (SLM) due to its capability of producing geometrically complex metal parts directly from CAD model in a few short steps. Many studies have been reported on static mechanical properties of SLM components; however, dynamic properties of SLM components of different materials have not been thoroughly investigated. Only few papers have been published on the dynamic mechanical behavior, especially in the crack resistance of selective laser melted AlSi10Mg alloy. In the present study, the effect of loading rate, dynamic versus quasi static, on the fracture toughness of the as-built alloy (X and Z orientations) has been investigated. The experimental results revealed the inherently anisotropic behavior for loading rates where the Z orientation exhibited lower toughness compared to the x orientation. The dynamic loading by impact, resulted in a significant decrease of the toughness values up to about 50% compared to the quasi-static loading. This mechanical response was attributed to the increase in the yield stress which alters the state stress at the crack tip from the planestress to some extent of the mix-mode plane stress/strain.