Mirenia Kalina Teixeira de Brito
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mirenia Kalina Teixeira de Brito has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
A.G. Barbosa de Lima
Federal University of Campina Grande (UFCG)
3 shared publications- Danilo Brito Teixeira Almeida
Post-Graduate Program in Electrical Engineering (PPgEE), Center of Alternative and Renewable Energies (CEAR), Federal University of Paraíba (UFPB), João Pessoa 58051-900, PB, Brazil
2 shared publications G. Moreira
Federal University of Campina Grande
2 shared publications- Wanessa Raphaella Gomes Dos Santos
Federal University of Campina Grande
2 shared publications Antonio Gilson Barbosa Lima
1 shared publication- Antonio Gilson Barbosa de Lima
Department of Mechanical Engineering, Federal University of Campina Grande, Campina Grande 58429-900, Brazil
1 shared publication
Latest Publications
- Open Access
Moisture Absorption in Polymer Composites Reinforced with Vegetable Fiber: A Three-Dimensional Investigation via Langmuir Model
This work aims to study numerically the moisture absorption in polymer composite reinforced with vegetable fibers using the Langmuir model which considers the existence of free and entrapped water molecules inside the material. A three-dimensional and transient modeling for describing the water absorption process inside the composite and its numerical solution via finite volume method were presented and discussed. Application has been made for polymer composites reinforced with sisal fiber. Emphasis was given to the effect of the layer thickness of fluid close to the wall of the composite in the progress of water migration. Results of the free and entrapped solute (water) concentration, local moisture content and average moisture content, at different times of process, and inside the composite were presented and analyzed. It was verified that concentration gradients of the molecules (free and entrapped) are higher in the material surface, at any time of the process, and concentration of free solute is greater than the concentration of entrapped solute. It was verified that the water layer thickness surrounding the composite strongly affects the moisture absorption rate.
Open AccessMoisture Absorption in Polymer Composites Reinforced with Vegetable Fiber: A Three-Dimensional Investigation via Langmuir Model
This work aims to study numerically the moisture absorption in polymer composite reinforced with vegetable fibers using the Langmuir model which considers the existence of free and entrapped water molecules inside the material. A three-dimensional and transient modeling for describing the water absorption process inside the composite and its numerical solution via finite volume method were presented and discussed. Application has been made for polymer composites reinforced with sisal fiber. Emphasis was given to the effect of the layer thickness of fluid close to the wall of the composite in the progress of water migration. Results of the free and entrapped solute (water) concentration, local moisture content and average moisture content, at different times of process, and inside the composite were presented and analyzed. It was verified that concentration gradients of the molecules (free and entrapped) are higher in the material surface, at any time of the process, and concentration of free solute is greater than the concentration of entrapped solute. It was verified that the water layer thickness surrounding the composite strongly affects the moisture absorption rate.
- 10 September 2019
- Published by Trans Tech Publications, Ltd. in Diffusion Foundations and Materials Applications
- Vol. 24, 11-24
Waterflooding Process in an Irregularly Shaped Oil Reservoir: A Finite-Volume Approach
Oil reservoirs are porous and permeable rocks that allow the hydrocarbon accumulation. Reservoir simulations are necessary to obtain the best fluid flow conditions in the porous medium and increase oil recovery capacity. The aim of this paper was to study the influence of the absolute rock permeability on the oil recovery of a complex geometry oil reservoir, using water injection with the black oil model. Numerical simulations in boundary-fitted coordinates were performed in a two-dimensional and irregularly shaped reservoir. Finite volume method was used to solve the governing equations and two inverted five-spot meshes were set in parallel for a total injection time of 30 years. Results of injected porous volume per recovered oil volume, the water cut charts and the water saturations maps showed that the lower porous medium permeability increased the oil recovery, once the permeability intensified fingers and early breakthrough, which leads to high water production rates and consequent reduction of the waterflooding efficiency.
- 10 September 2019
- Published by Trans Tech Publications, Ltd. in Diffusion Foundations and Materials Applications
- Vol. 24, 11-24
Waterflooding Process in an Irregularly Shaped Oil Reservoir: A Finite-Volume Approach
Oil reservoirs are porous and permeable rocks that allow the hydrocarbon accumulation. Reservoir simulations are necessary to obtain the best fluid flow conditions in the porous medium and increase oil recovery capacity. The aim of this paper was to study the influence of the absolute rock permeability on the oil recovery of a complex geometry oil reservoir, using water injection with the black oil model. Numerical simulations in boundary-fitted coordinates were performed in a two-dimensional and irregularly shaped reservoir. Finite volume method was used to solve the governing equations and two inverted five-spot meshes were set in parallel for a total injection time of 30 years. Results of injected porous volume per recovered oil volume, the water cut charts and the water saturations maps showed that the lower porous medium permeability increased the oil recovery, once the permeability intensified fingers and early breakthrough, which leads to high water production rates and consequent reduction of the waterflooding efficiency.
- 1 February 2019
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 391, 136-141
Solidification of Ni-Ti Shape Memory Alloy: Modeling and Simulation
The shape memory alloys have been used in the most different sectors such as aerospace, automotive and biomedical due to their ability to return to their original shape when subjected to high temperatures.Modeling and numerical simulation have become great allies in engineering due to the possibility of solving complex problems, especially in cases where experimental research is limited. In the present study, a two-dimensional mathematical model was developed to describe the solidification process of a Ni-Ti alloy in a stainless-steel metal mold sand-confined. It was considered the flow of a refrigerant (air) in the top of the mold. The energy conservation equation, including the phase change term, was discretized using finite volume method (FVM) and a fully implicit formulation. Results of the Ni-Ti alloy and mold temperature distributions over time are presented and analyzed.
- 1 February 2019
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 391, 136-141
Solidification of Ni-Ti Shape Memory Alloy: Modeling and Simulation
The shape memory alloys have been used in the most different sectors such as aerospace, automotive and biomedical due to their ability to return to their original shape when subjected to high temperatures.Modeling and numerical simulation have become great allies in engineering due to the possibility of solving complex problems, especially in cases where experimental research is limited. In the present study, a two-dimensional mathematical model was developed to describe the solidification process of a Ni-Ti alloy in a stainless-steel metal mold sand-confined. It was considered the flow of a refrigerant (air) in the top of the mold. The energy conservation equation, including the phase change term, was discretized using finite volume method (FVM) and a fully implicit formulation. Results of the Ni-Ti alloy and mold temperature distributions over time are presented and analyzed.
- Open Access
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 22 (suppl 1)
Study of the Moisture Absorption in Polymer Composites Reinforced with Vegetal Fiber Using Langmuir’s Model
This work aims to numerically study the moisture absorption in polymer composites reinforced with vegetal fiber, using the diffusive model of Langmuir, which considers the existence of water molecules inside the material free to diffuse and adsorb at the capillaries walls, in the solid. A three-dimensional and transient mathematical modelling to describe the water absorption process by the composite and its numerical solution via finite volume method are presented and discussed. Results of the free solute concentration, entrapped solute concentration, local moisture content and average moisture content obtained at different instants of the process are presented and analyzed. It was verified that the concentration gradients of the molecules (free and entrapped) are higher at the material surface. In addition, as the concentration of free water increases, there is also an increase in entrapped water concentration within the material at any time of the process.
- 1 January 2019
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 22 (suppl 1)
Open AccessStudy of the Moisture Absorption in Polymer Composites Reinforced with Vegetal Fiber Using Langmuir’s Model
This work aims to numerically study the moisture absorption in polymer composites reinforced with vegetal fiber, using the diffusive model of Langmuir, which considers the existence of water molecules inside the material free to diffuse and adsorb at the capillaries walls, in the solid. A three-dimensional and transient mathematical modelling to describe the water absorption process by the composite and its numerical solution via finite volume method are presented and discussed. Results of the free solute concentration, entrapped solute concentration, local moisture content and average moisture content obtained at different instants of the process are presented and analyzed. It was verified that the concentration gradients of the molecules (free and entrapped) are higher at the material surface. In addition, as the concentration of free water increases, there is also an increase in entrapped water concentration within the material at any time of the process.
- 1 June 2017
- Published by Trans Tech Publications, Ltd. in Diffusion Foundations and Materials Applications
- Vol. 10, 93-106
Heat and Mass Transfer during Drying of Clay Ceramic Materials: A Three-Dimensional Analytical Study
This work aims to study heat and mass transfer in solids with parallelepiped shape with particular reference to drying process. A transient three-dimensional mathematical model based on the Fick ́s and Fourier ́s Laws was developed to predict heat and mass transport in solids considering constant physical properties and convective boundary conditions at the surface of the solid. The analytical solution of the governing equations was obtained using the method of separation of variables. The study was applied in the drying of common ceramic bricks. Predicted results of the heating and drying kinetics and the moisture and temperature distributions inside the material during the process, are compared with experimental data and good agreement was obtained. It has been found that the vertices of the solid dry and heat first. This provokes thermal and hydric stresses inside the material, which may compromise the quality of the product after drying.
- 1 June 2017
- Published by Trans Tech Publications, Ltd. in Diffusion Foundations and Materials Applications
- Vol. 10, 93-106
Heat and Mass Transfer during Drying of Clay Ceramic Materials: A Three-Dimensional Analytical Study
This work aims to study heat and mass transfer in solids with parallelepiped shape with particular reference to drying process. A transient three-dimensional mathematical model based on the Fick ́s and Fourier ́s Laws was developed to predict heat and mass transport in solids considering constant physical properties and convective boundary conditions at the surface of the solid. The analytical solution of the governing equations was obtained using the method of separation of variables. The study was applied in the drying of common ceramic bricks. Predicted results of the heating and drying kinetics and the moisture and temperature distributions inside the material during the process, are compared with experimental data and good agreement was obtained. It has been found that the vertices of the solid dry and heat first. This provokes thermal and hydric stresses inside the material, which may compromise the quality of the product after drying.