Yuanqing Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yuanqing Chen has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Guangli Yang
Shanghai Institute for Advanced Communication and Data Science, Shanghai University, Shanghai, China
4 shared publications - Bin Xu
Qualcomm, San Diego, 92122, USA
3 shared publications - Yong Luo
Shanghai Key Laboratory of Chips and Systems for Intelligent Connected Vehicle, School of Communication and Information Engineering, Shanghai University, Shanghai, China
3 shared publications - Hao Jin
Guangxi University of Science and Technology, Liuzhou, China
2 shared publications - Fan Li
Shanghai Institute for Advanced Communication and Data Science (SICS), School of Communication and Information Engineering, Shanghai University, Shanghai 200444 China
1 shared publication - Fuxue Yan
School of Materials Science and Engineering, Xi’an University of Technology, Xi’an, PR China
1 shared publication
Latest Publications
- 9 January 2024
- Published by Elsevier in Building and Environment
- Vol. 250
Impact of urban canopy characteristics on turbulence dynamics: Insights from large eddy simulation
- 9 January 2024
- Published by Elsevier in Building and Environment
- Vol. 250
Impact of urban canopy characteristics on turbulence dynamics: Insights from large eddy simulation
- Open Access
- 6 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 177607-177615
A Zero-Mode Induced mmWave Patch Antenna With Low-Profile, Wide-Bandwidth and Large-Angle Scanning for 5G Mobile Terminals
Millimeter-Wave (mmWave) antennas for 5G mobile terminals require a wide bandwidth, large-angle beam scanning, low-profile design, and multi-substrate compatibility for module-level integration. In this paper, we propose one candidate design employing a patch structure with the shorting pin to particularly generate extra zero modes. By taking advantages of the 2 nd zero-mode with the TM 01 mode, we can obtain a wide bandwidth covering 23.5~28 GHz, a large-angle beam scanning with ±60°, as well as keep the substrate as low profile as 0.508 mm. Thanks to the zero-mode induced patch-type design, it is compatible to multi-layer configuration possessing the extensibility and flexibility for further module design. We experimentally valid the design of a $4\times2$ array with multi-layer configuration in a cell phone environment. Good RF performances with ±60° scanning in the wide bandwidth indicate this proposed design can be an appropriate candidate for 5G mobile terminals.
- 6 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 177607-177615
Open AccessA Zero-Mode Induced mmWave Patch Antenna With Low-Profile, Wide-Bandwidth and Large-Angle Scanning for 5G Mobile Terminals
Millimeter-Wave (mmWave) antennas for 5G mobile terminals require a wide bandwidth, large-angle beam scanning, low-profile design, and multi-substrate compatibility for module-level integration. In this paper, we propose one candidate design employing a patch structure with the shorting pin to particularly generate extra zero modes. By taking advantages of the 2 nd zero-mode with the TM 01 mode, we can obtain a wide bandwidth covering 23.5~28 GHz, a large-angle beam scanning with ±60°, as well as keep the substrate as low profile as 0.508 mm. Thanks to the zero-mode induced patch-type design, it is compatible to multi-layer configuration possessing the extensibility and flexibility for further module design. We experimentally valid the design of a $4\times2$ array with multi-layer configuration in a cell phone environment. Good RF performances with ±60° scanning in the wide bandwidth indicate this proposed design can be an appropriate candidate for 5G mobile terminals.
- Open Access
- 18 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 171684-171690
A Wide-Angle Beam Scanning Antenna in E-plane for K-band Radar Sensor
In this paper, a K-band antenna with ±60° beam scanning is proposed for a mmWave (millimeter-Wave) radar sensor. Especially, we take advantages of the magnetic dipole principle, and design the antenna by employing via holes in three sides, so as to form a cavity which can be equivalently considered as magnetic dipole, resulting in the 3 dB beam width as wide as 140° in E-plane. We cascade the mmWave antenna to 4×1 and 4×4 arrays for radar transmitting and receiving, respectively. The antenna array is fabricated and implemented to a K-band radar and its wide-angle beam scanning performance is evaluated by the radar’s distance and angular detections.
- 18 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 171684-171690
Open AccessA Wide-Angle Beam Scanning Antenna in E-plane for K-band Radar Sensor
In this paper, a K-band antenna with ±60° beam scanning is proposed for a mmWave (millimeter-Wave) radar sensor. Especially, we take advantages of the magnetic dipole principle, and design the antenna by employing via holes in three sides, so as to form a cavity which can be equivalently considered as magnetic dipole, resulting in the 3 dB beam width as wide as 140° in E-plane. We cascade the mmWave antenna to 4×1 and 4×4 arrays for radar transmitting and receiving, respectively. The antenna array is fabricated and implemented to a K-band radar and its wide-angle beam scanning performance is evaluated by the radar’s distance and angular detections.
- Open Access
- 13 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 167470-167480
Dual-Functional MIMO Antenna Array With High Isolation for 5G/WLAN Applications in Smartphones
A dual-functional antenna array operating in the long term evolution (LTE) band 42 (3.4–3.6 GHz) and 5.8-GHz wireless wide area network (WLAN) band (5.725–5.875 GHz) for multiple-input multiple-output (MIMO) applications in 5G smartphones is proposed. The proposed 8-antenna array is composed of two different antenna elements, namely, the folded L-shaped antenna and couple-fed Ushaped antenna. It can be applied in the 8 × 8 (by using 8 antenna elements) and 4 × 4 (by using 4 antenna elements) MIMO system across the LTE band 42 and 5.8-GHz WLAN band, respectively. The quasiorthogonal polarization, balanced mode excitation and pattern diversity are properly used to achieve high isolation within the operation bands. A prototype of the proposed antenna array was fabricated and measured. The measured isolations in the LTE band 42 (6-dB impedance matching) and 5.8-GHz WLAN band (10-dB impedance matching) are better than 17.1 dB and 34.6 dB, respectively. The total efficiencies are 45%–62% and 52%–59% in the two operation bands, respectively. Besides, the measured envelope correlation coefficients (ECCs) are less than 0.045 and 0.0001, the calculated peak ergodic channel capacities are 37.9 bps/Hz and 19.3 bps/Hz in the 8 × 8 or 4 × 4 MIMO system across the operation bands. Furthermore, user’s hand and head effects are investigated and desirable results are obtained. The above results show that this proposed antenna array is a good candidate for MIMO applications in smartphones.
- 13 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 167470-167480
Open AccessDual-Functional MIMO Antenna Array With High Isolation for 5G/WLAN Applications in Smartphones
A dual-functional antenna array operating in the long term evolution (LTE) band 42 (3.4–3.6 GHz) and 5.8-GHz wireless wide area network (WLAN) band (5.725–5.875 GHz) for multiple-input multiple-output (MIMO) applications in 5G smartphones is proposed. The proposed 8-antenna array is composed of two different antenna elements, namely, the folded L-shaped antenna and couple-fed Ushaped antenna. It can be applied in the 8 × 8 (by using 8 antenna elements) and 4 × 4 (by using 4 antenna elements) MIMO system across the LTE band 42 and 5.8-GHz WLAN band, respectively. The quasiorthogonal polarization, balanced mode excitation and pattern diversity are properly used to achieve high isolation within the operation bands. A prototype of the proposed antenna array was fabricated and measured. The measured isolations in the LTE band 42 (6-dB impedance matching) and 5.8-GHz WLAN band (10-dB impedance matching) are better than 17.1 dB and 34.6 dB, respectively. The total efficiencies are 45%–62% and 52%–59% in the two operation bands, respectively. Besides, the measured envelope correlation coefficients (ECCs) are less than 0.045 and 0.0001, the calculated peak ergodic channel capacities are 37.9 bps/Hz and 19.3 bps/Hz in the 8 × 8 or 4 × 4 MIMO system across the operation bands. Furthermore, user’s hand and head effects are investigated and desirable results are obtained. The above results show that this proposed antenna array is a good candidate for MIMO applications in smartphones.
- 21 November 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 22 (6) , 6601204
High-Performance $\hbox{GdBa}_{2}\hbox{Cu}_{3} \hbox{O}_{7 - {x}}$ Superconducting Film Prepared Using an Advanced Low-Fluorine SolutionAn advanced low-fluorine GdBa2Cu3 O7-x (GBCO) precursor solution was prepared using barium, gadolinium, and copper acetates as starting materials; lactic acid, methacrylic acid, and trifluoroacetic acid as additives; and methanol as a solvent. The gel-film cast from this solution consisted of Gd trifluoroacetate and fluorine-free Ba and Cu salts. The BaCO3-free precursor was obtained through the pyrolysis of the gel film. After firing at 820 °C, the precursor was finally transformed to a phase-pure GBCO film. The critical current density (Jc) of the GBCO film was measured to reach 3.3 MA/cm2 (at 77 K, 0 T), and its critical transition temperature (Tc) was 92.6 K. During the pyrolyzing of the film, the relatively small amount of released fluorinated gases resulted in the rapid fabrication of GBCO film.
- 21 November 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 22 (6) , 6601204
High-Performance $\hbox{GdBa}_{2}\hbox{Cu}_{3} \hbox{O}_{7 - {x}}$ Superconducting Film Prepared Using an Advanced Low-Fluorine SolutionAn advanced low-fluorine GdBa2Cu3 O7-x (GBCO) precursor solution was prepared using barium, gadolinium, and copper acetates as starting materials; lactic acid, methacrylic acid, and trifluoroacetic acid as additives; and methanol as a solvent. The gel-film cast from this solution consisted of Gd trifluoroacetate and fluorine-free Ba and Cu salts. The BaCO3-free precursor was obtained through the pyrolysis of the gel film. After firing at 820 °C, the precursor was finally transformed to a phase-pure GBCO film. The critical current density (Jc) of the GBCO film was measured to reach 3.3 MA/cm2 (at 77 K, 0 T), and its critical transition temperature (Tc) was 92.6 K. During the pyrolyzing of the film, the relatively small amount of released fluorinated gases resulted in the rapid fabrication of GBCO film.