Ko-Ta Chiang
Research Subjects
Ko-Ta Chiang has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Chih-Cherng Chen
Department of Automatic and Control Engineering, ChungChou Institute of Technology, Changhua, Republic of China
3 shared publications Nun-Ming Liu
Department of Mechanical Engineering, Hsiuping Institute of Technology, Dali City, Taichung, Republic of China
3 shared publications- Chih-Chung Chou
Hsiuping Inst Technol, Dept Mech Engn, Dali City 41280, Taichung, Taiwan
2 shared publications Fu-Ping Chang
Department of Mechanical Engineering, Hsiu-Ping Institute of Technology, Taichung, Republic of China
2 shared publicationsJenn-Tsong Horng
Hsiuping Institute of Technology
2 shared publicationsTe-Chang Tsai
Hsiuping Inst Technol, Dept Mech Engn, Dali City 41280, Taichung, Taiwan
2 shared publications
Latest Publications
- 1 September 2011
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 32 (8-9) , 4187-4194
Modeling and analyzing the effects of heat treatment on the characteristics of magnesium alloy joint welded by the tungsten-arc inert gas welding
- 1 September 2011
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 32 (8-9) , 4187-4194
Modeling and analyzing the effects of heat treatment on the characteristics of magnesium alloy joint welded by the tungsten-arc inert gas welding
- 6 April 2011
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 57 (1-4) , 101-116
Analyzing the design of vibration reduction with the rubber-layered laminates in the precision turning with a diamond cutting tool
- 6 April 2011
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 57 (1-4) , 101-116
Analyzing the design of vibration reduction with the rubber-layered laminates in the precision turning with a diamond cutting tool
- 6 October 2010
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 54 (5-8) , 465-478
The use of D-optimal design for modeling and analyzing the vibration and surface roughness in the precision turning with a diamond cutting tool
- 6 October 2010
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 54 (5-8) , 465-478
The use of D-optimal design for modeling and analyzing the vibration and surface roughness in the precision turning with a diamond cutting tool
- 12 April 2010
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 51 (5-8) , 587-598
Modeling and analysis of the edge disintegration in the EDM drilling cobalt-bonded tungsten carbide
- 12 April 2010
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 51 (5-8) , 587-598
Modeling and analysis of the edge disintegration in the EDM drilling cobalt-bonded tungsten carbide
- 31 March 2008
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 23 (3) , 241-250
Modeling and Analysis of Machinability Evaluation in the Wire Electrical Discharge Machining (WEDM) Process of Aluminum Oxide-Based Ceramic
The wire electrical discharge machining (WEDM) allowed success in the manufacture of the hard, fragile, and materials difficult to cut, especially for electroconductive ceramic materials. In this study, the mathematical models of material removal rate (MRR) and surface roughness (SR) used for the machinability evaluation in the WEDM process of aluminum oxide-based ceramic material (Al2O3 + TiC) have been carried out. The experimental plan adopts the face centered central composite design (CCD). The mathematical models using the response surface methodology (RSM) are developed so as to investigate the influences of four machining parameters, including the peak current, pulse on time, duty factor, and wire speed, on the performance characteristics of MRR and SR. It has been proved that the proposed mathematical models in this study would fit and predict values of the performance characteristics, which would be close to the readings recorded in experiment with a 95% confidence level. The significant parameters that critically affect the performance characteristics are examined.
- 31 March 2008
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 23 (3) , 241-250
Modeling and Analysis of Machinability Evaluation in the Wire Electrical Discharge Machining (WEDM) Process of Aluminum Oxide-Based Ceramic
The wire electrical discharge machining (WEDM) allowed success in the manufacture of the hard, fragile, and materials difficult to cut, especially for electroconductive ceramic materials. In this study, the mathematical models of material removal rate (MRR) and surface roughness (SR) used for the machinability evaluation in the WEDM process of aluminum oxide-based ceramic material (Al2O3 + TiC) have been carried out. The experimental plan adopts the face centered central composite design (CCD). The mathematical models using the response surface methodology (RSM) are developed so as to investigate the influences of four machining parameters, including the peak current, pulse on time, duty factor, and wire speed, on the performance characteristics of MRR and SR. It has been proved that the proposed mathematical models in this study would fit and predict values of the performance characteristics, which would be close to the readings recorded in experiment with a 95% confidence level. The significant parameters that critically affect the performance characteristics are examined.
- 7 December 2007
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 40 (1-2) , 95-104
Material removal rate and electrode wear ratio study on the powder mixed electrical discharge machining of cobalt-bonded tungsten carbide
- 7 December 2007
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 40 (1-2) , 95-104
Material removal rate and electrode wear ratio study on the powder mixed electrical discharge machining of cobalt-bonded tungsten carbide
- 14 June 2007
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 38 (3-4) , 229-237
Machining parameters optimization on the die casting process of magnesium alloy using the grey-based fuzzy algorithm
- 14 June 2007
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 38 (3-4) , 229-237
Machining parameters optimization on the die casting process of magnesium alloy using the grey-based fuzzy algorithm