Azman Jalar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Interests
Azman Jalar has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Maria Abu Bakar
Univ Kebangsaan Malaysia, Inst Kejuruteraan Mikro & Nano Elekt IMEN, Ukm Bangi 43600, Selangor Darul, Malaysia
3 shared publications- Muhammad Nubli Zulkifli
Universiti Kuala Lumpur Electrical Engineering Section, Renewable Energy Research Laboratory, British Malaysia Institute Kuala Lumpur
3 shared publications - Norliza Ismail
Universiti Kebangsaan Malaysia (UKM)
3 shared publications - Irman Abdul Rahman
School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor, Malaysia
2 shared publications - Norinsan Kamil Othman
Department of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, Bangi, Malaysia
2 shared publications Roslina Ismail
Univ Malaya, Cultural Ctr, Div Fine Arts, Kuala Lumpur 50603, Wilayah Perseku, Malaysia
2 shared publications
Latest Publications
- 30 June 2019
- Published by Penerbit Universiti Kebangsaan Malaysia (UKM Press) in Sains Malaysiana
- Vol. 48 (6) , 1267-1272
Kesan Penuaan Sesuhu terhadap Sifat Mikro Kekerasan Pempaterian Sn-Ag-Cu/CNT/Cu menggunakan Pelekukan Nano
- 30 June 2019
- Published by Penerbit Universiti Kebangsaan Malaysia (UKM Press) in Sains Malaysiana
- Vol. 48 (6) , 1267-1272
Kesan Penuaan Sesuhu terhadap Sifat Mikro Kekerasan Pempaterian Sn-Ag-Cu/CNT/Cu menggunakan Pelekukan Nano
- Open Access
- 6 November 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 409 (1) , 012013
Shock Wave Effect on Micromechanics Properties of Sn-Ag-Cu solder (SAC 387) via Nanoindentation
A variety of Sn-Ag-Cu solder alloys have been proposed and recommended for use in industrial organizations for example Sn-95.5Ag3.8Cu-0.7 (SAC 387) by the European Consortium Brite-Euram in the European Union. In this study an effect of shock wave on micromechanics properties of SAC 387 solder was investigated via nanoindentation approach. Solder joint of SAC 387 on copper substrate was prepared by hand soldering techniques. Then soldered samples were exposed to shock wave at different distance of 1 m, 2 m and 3 m. The shock wave test was conducted using 500 g of trinitrotoluene (TNT). Hardness value of SAC 387 decreased from 300 MPa to 130 MPa as well as reduced modulus drop from 115 GPa to 43 GPa after exposure. However the hardness and reduced modulus increased with increasing distance of the shock wave. The phenomenon revealed that shock wave deteriorated the micromechanics properties of soldered samples.
- 6 November 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 409 (1) , 012013
Open AccessShock Wave Effect on Micromechanics Properties of Sn-Ag-Cu solder (SAC 387) via Nanoindentation
A variety of Sn-Ag-Cu solder alloys have been proposed and recommended for use in industrial organizations for example Sn-95.5Ag3.8Cu-0.7 (SAC 387) by the European Consortium Brite-Euram in the European Union. In this study an effect of shock wave on micromechanics properties of SAC 387 solder was investigated via nanoindentation approach. Solder joint of SAC 387 on copper substrate was prepared by hand soldering techniques. Then soldered samples were exposed to shock wave at different distance of 1 m, 2 m and 3 m. The shock wave test was conducted using 500 g of trinitrotoluene (TNT). Hardness value of SAC 387 decreased from 300 MPa to 130 MPa as well as reduced modulus drop from 115 GPa to 43 GPa after exposure. However the hardness and reduced modulus increased with increasing distance of the shock wave. The phenomenon revealed that shock wave deteriorated the micromechanics properties of soldered samples.
- 31 July 2018
- Published by Penerbit Universiti Kebangsaan Malaysia (UKM Press) in Sains Malaysiana
- Vol. 47 (07) , 1585-1590
Kesan Penambahan Tiubnano Karbon terhadap Pertumbuhan Lapisan Sebatian antara Logam Sistem Pateri Sn-Ag-Cu/Cu akibat Penuaan Terma
- 31 July 2018
- Published by Penerbit Universiti Kebangsaan Malaysia (UKM Press) in Sains Malaysiana
- Vol. 47 (07) , 1585-1590
Kesan Penambahan Tiubnano Karbon terhadap Pertumbuhan Lapisan Sebatian antara Logam Sistem Pateri Sn-Ag-Cu/Cu akibat Penuaan Terma
- 28 December 2014
- Published by Springer Nature
- p. 159-171
Shear Strength of Single Lap Joint Aluminium-Thermoplastic Natural Rubber (Al-TPNR) Laminated Composite
- 28 December 2014
- Published by Springer Nature
- p. 159-171
Shear Strength of Single Lap Joint Aluminium-Thermoplastic Natural Rubber (Al-TPNR) Laminated Composite
- Open Access
- 1 January 2014
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2014, 1-10
Characterization of Oxide Growth on Surface of Al-Mg-Si Welded Joint
Al-Mg-Si (AA6061) Al alloy plates were joined by the method of gas metal arc welding using Al-5Mg (ER5356) filler metal and were subjected to the oxidation test in flowing air environment atfrom 8 to 40 hours and the weight gain was measured. The characteristic of oxide grown on welded zone surface was examined by SEM/EDS, XRD, and XPS. Oxide was observed to grow on the fused metal surface suggesting the possibility of modifying the oxide chemistry under high temperature environment. It was found that the oxidation behavior of fused metal affected by the nature of their oxide growth and morphology, was influenced by their welding process and the difference in the chemical composition.- 1 January 2014
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2014, 1-10
Open AccessCharacterization of Oxide Growth on Surface of Al-Mg-Si Welded Joint
Al-Mg-Si (AA6061) Al alloy plates were joined by the method of gas metal arc welding using Al-5Mg (ER5356) filler metal and were subjected to the oxidation test in flowing air environment atfrom 8 to 40 hours and the weight gain was measured. The characteristic of oxide grown on welded zone surface was examined by SEM/EDS, XRD, and XPS. Oxide was observed to grow on the fused metal surface suggesting the possibility of modifying the oxide chemistry under high temperature environment. It was found that the oxidation behavior of fused metal affected by the nature of their oxide growth and morphology, was influenced by their welding process and the difference in the chemical composition. - 1 August 2013
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 577, 189-196
Strength distribution of Au ball bond using nanoindentation approach
- 1 August 2013
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 577, 189-196
Strength distribution of Au ball bond using nanoindentation approach
- 5 March 2013
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 42 (6) , 1063-1072
Effect of Applied Load in the Nanoindentation of Gold Ball Bonds
- 5 March 2013
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 42 (6) , 1063-1072
Effect of Applied Load in the Nanoindentation of Gold Ball Bonds
- Open Access
- 2 August 2012
- Published by Springer Nature in Gold Bulletin
- Vol. 45 (3) , 115-125
Some thoughts on bondability and strength of gold wire bonding
- 2 August 2012
- Published by Springer Nature in Gold Bulletin
- Vol. 45 (3) , 115-125
Open AccessSome thoughts on bondability and strength of gold wire bonding