FFFernanda Cavalcanti Ferreira

Fernanda Cavalcanti Ferreira

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Fernanda Cavalcanti Ferreira has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Evaluation of compressive strength of concrete with metakaolin using different levelling techniques

    by Ayrton Wagner dos Santos Gomes de Sá, Yane Coutinho, Renan Gustavo Pacheco Soares, Fernanda Cavalcanti Ferreira, Arnaldo Manoel Pereira Carneiro

    The partial replacement of cement by mineral additions such as metakaolin has been widely applied in the production of high-strength and durable concretes due to the pozzolanic action, allowing a reduction in the consumption of cement. Tests are performed to determine the mechanical properties of these materials, such as compressive strength, for which there are different levelling techniques of specimens, such as sulphur and neoprene, indicated for different resistance classes. The present study aimed to characterize the behaviour, in the hardened state, of concrete produced with high initial strength Portland cement (CPV-ARI) and metakaolin and evaluate the different levelling methods. Three groups of samples dosed by the IPT-EPUSP method, with mix designs of 1:3, 1:5, and 1:6, and replacements of 8 and 10% of cement by metakaolin, were subjected to compressive strength test, at the ages of 28 days, with levelling by neoprene, and 90 days, with levelling by sulphur. It was observed an increase in strength with addition of metakaolin at both ages. Comparing the results in the two ages, it was verified an increase in strength for the mix designs 1:5 and 1:6 and a reduction for the mix design 1:3. Such fact can be explained by the high strengths achieved by this mix design. As the levelling method used was sulphur, it is confirmed the imprecision of results for strengths above 50 MPa with this technique.


  • Open Access

    Evaluation of mechanical properties of concrete produced with binary and ternary mixtures of aggregate

    by Fernanda Cavalcanti Ferreira, Yane Coutinho, Arnaldo Manoel Pereira Carneiro

    Cement is the costlier component of concrete, and its productive process causes considerable environmental impact. Thus, alternatives are studied to reduce the amount of cement used. An option is the use of optimized grain size curves of aggregates, aiming to achieve a higher compactness of concrete. An ideal grain size distribution results in a higher mechanical resistance of concrete, providing a reduction in cost and consumption of materials, and, consequently, in environmental impacts. Therefore, the present study aims to improve the properties of conventional concrete through optimized grain size distributions. In this research, concrete was produced with binary mixtures with rolled pebbles from Belém region, in Pará state, and ternary mixtures of granitic crushed stone from the metropolitan region of Recife, in Pernambuco state, and concrete properties in the hardened state were studied. The mix design IPT/EPUSP method was used and grain size composition, unit weight, water absorption by capillarity, and compressive strength tests were performed. It was observed an increase in compressive strength with for higher fine contents. Furthermore, for both aggregates studied, there was no loss in strength with the lower amount of cement used, due to the increased compactness of the concrete, indicated by the unit weight of the aggregate mixture. Therefore, the optimization of the grain size composition of the coarse aggregate provided a reduction in the cement consumption for the same required strength and for both analysed aggregates.


  • Open Access

    Caracterização mecânica do gesso para revestimento produzido no Polo Gesseiro do Araripe

    by Fernanda Cavalcanti Ferreira, José Getulio Gomes de Sousa, Arnaldo Manoel Pereira Carneiro

    Resumo O gesso é um material de grande uso na construção civil, destacando-se seu emprego como pasta de gesso para revestimento. No Brasil, o Polo Gesseiro do Araripe é o maior produtor. Percebe-se a necessidade de conhecimento das propriedades e características desse material, principalmente, com foco no produto acabado como revestimento interno em paredes. Nesse contexto, o presente trabalho visa realizar um estudo de caracterização de cinco amostras de gesso do Polo do Araripe, e avaliar a capacidade aderente dos revestimentos executados em pasta desses gessos. O estudo de caracterização ocorreu no estado anidro, por meio de ensaios de granulometria, massa unitária, massa específica, teores de água livre e de cristalização; no estado fresco, por meio de ensaios de consistência normal, tempo de pega e calorimetria; e no estado endurecido, por ensaios de dureza e resistência à compressão. Os ensaios de resistência de aderência à tração ocorreram nos revestimentos de pasta de gesso executados em base cerâmica, produzidos com e sem pré-umedecimento da base. Com os resultados, verifica-se que as pastas de gesso apresentam desempenhos satisfatórios e semelhantes, independentemente do porte do fabricante; entretanto, alguns requisitos normativos não são atendidos.