Andreas Klehr
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andreas Klehr has a total of 91 co-authors. Here are the top co-authors by number of shared publications:
- Hans Wenzel
Ferdinand-Braun-Institut (FBH)
10 shared publications G. Erbert
Ferdinand-Braun-Institut (Germany)
6 shared publicationsAndrea Knigge
4 shared publicationsGötz Erbert
Ferdinand-Braun-Institut (Germany)
4 shared publications- Günther Tränkle
Ferdinand-Braun-Institut (FBH), Berlin, Germany
4 shared publications - Armin Liero
Ferdinand-Braun-Institut (FBH), Gustav-Kirchhoff-Str. 4, Berlin, 12489, Germany
3 shared publications
Latest Publications
- 24 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 33 (3) , 151-154
High-Brightness Nanosecond-Pulse Operation From Tapered-Ridge-Waveguide Lasers
Carrier-induced anti-guiding effects emerging at extremely high injection current densities under short-pulse operation necessitate lateral-waveguide design considerations, that differ from those required when continuous-wave operation is desired. Here, we investigate variations of the lateral index-guiding trench design to achieve an excellent brightness value of 27.4 Wmm −1 mrad −1 from tapered-ridge-waveguide lasers with more than 18 W output power under 3.3 ns long pulse operation.
- 24 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 33 (3) , 151-154
High-Brightness Nanosecond-Pulse Operation From Tapered-Ridge-Waveguide Lasers
Carrier-induced anti-guiding effects emerging at extremely high injection current densities under short-pulse operation necessitate lateral-waveguide design considerations, that differ from those required when continuous-wave operation is desired. Here, we investigate variations of the lateral index-guiding trench design to achieve an excellent brightness value of 27.4 Wmm −1 mrad −1 from tapered-ridge-waveguide lasers with more than 18 W output power under 3.3 ns long pulse operation.
- Open Access
- 19 May 2020
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 35 (6) , 065016
Wavelength stabilized high pulse power 48 emitter laser bars for automotive light detection and ranging application
Diode lasers generating optical pulses with high peak power and lengths in the nanosecond range are key components for light detection and ranging systems, e.g. for autonomous driving and object detection. We present here an internally wavelength stabilized distributed Bragg reflector broad area laser bar with 48 emitters. The vertical structure based on AlGaAs (confinement and cladding layers) and InGaAs (active quantum well) is specifically optimized for wavelength-stabilized pulsed operation, applying a surface Bragg grating with high reflectivity. The bar is electrically driven by a new in-house developed high-speed driver based on GaN transistors providing current pulses with amplitudes of up to 1000 A and a repetition frequency of 10 kHz. The generated 4 ns to 10 ns long optical pulses are nearly rectangular shaped and reach a pulse peak power in excess of 600 Watts at 25 °C. The optical spectrum with a centre wavelength of about 900 nm has a width of 0.15 nm (FWHM) with a side mode suppression ratio > 30 dB.
- 19 May 2020
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 35 (6) , 065016
Open AccessWavelength stabilized high pulse power 48 emitter laser bars for automotive light detection and ranging application
Diode lasers generating optical pulses with high peak power and lengths in the nanosecond range are key components for light detection and ranging systems, e.g. for autonomous driving and object detection. We present here an internally wavelength stabilized distributed Bragg reflector broad area laser bar with 48 emitters. The vertical structure based on AlGaAs (confinement and cladding layers) and InGaAs (active quantum well) is specifically optimized for wavelength-stabilized pulsed operation, applying a surface Bragg grating with high reflectivity. The bar is electrically driven by a new in-house developed high-speed driver based on GaN transistors providing current pulses with amplitudes of up to 1000 A and a repetition frequency of 10 kHz. The generated 4 ns to 10 ns long optical pulses are nearly rectangular shaped and reach a pulse peak power in excess of 600 Watts at 25 °C. The optical spectrum with a centre wavelength of about 900 nm has a width of 0.15 nm (FWHM) with a side mode suppression ratio > 30 dB.
- Open Access
- 24 January 2020
- Published by IOP Publishing in Engineering Research Express
- Vol. 2 (1) , 015023
Versatile high power pulse-laser source for pico- and nanosecond optical pulses
- 24 January 2020
- Published by IOP Publishing in Engineering Research Express
- Vol. 2 (1) , 015023
Open AccessVersatile high power pulse-laser source for pico- and nanosecond optical pulses
- 11 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 25 (6) , 1-10
Impact of Carrier Nonpinning Effect on Thermal Power Saturation in GaAs-Based High Power Diode Lasers
A root-cause analysis of thermal power saturation in broad area diode lasers is presented. Thermal power saturation limits in largest parts the optical power in continuous wave (CW) driven diode lasers, as junction temperature increases with bias. Accordingly, gain decreases and hence the carrier density in the quantum well increases (non-pinning) to compensate the low gain and the additional photon loss. A systematic variation of epitaxial designs was used to experimentally clarify the impact of modal gain on the temperature dependence of differential internal efficiency and optical loss. To account for this effect in simulation, a rate equation model was applied to determine temperature dependent slope efficiency. Longitudinal spatial hole burning (LSHB) causes an asymmetry of the carrier density profile, leading to high non-linear carrier loss at the back facet, but also the average carrier density increases with temperature, enhancing the impact of LSHB. This enhancement effect leads to rapid degradation of internal differential efficiency with temperature and hence early power saturation. The extreme triple asymmetric vertical design is introduced, that enables devices to be realized that show minimized degradation of internal differential efficiency with temperature and therefore increased performance in CW operation.
- 11 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 25 (6) , 1-10
Impact of Carrier Nonpinning Effect on Thermal Power Saturation in GaAs-Based High Power Diode Lasers
A root-cause analysis of thermal power saturation in broad area diode lasers is presented. Thermal power saturation limits in largest parts the optical power in continuous wave (CW) driven diode lasers, as junction temperature increases with bias. Accordingly, gain decreases and hence the carrier density in the quantum well increases (non-pinning) to compensate the low gain and the additional photon loss. A systematic variation of epitaxial designs was used to experimentally clarify the impact of modal gain on the temperature dependence of differential internal efficiency and optical loss. To account for this effect in simulation, a rate equation model was applied to determine temperature dependent slope efficiency. Longitudinal spatial hole burning (LSHB) causes an asymmetry of the carrier density profile, leading to high non-linear carrier loss at the back facet, but also the average carrier density increases with temperature, enhancing the impact of LSHB. This enhancement effect leads to rapid degradation of internal differential efficiency with temperature and hence early power saturation. The extreme triple asymmetric vertical design is introduced, that enables devices to be realized that show minimized degradation of internal differential efficiency with temperature and therefore increased performance in CW operation.
- 9 May 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10682, 106821Z
Timing stability and repetition rate frequency tuning analysis of a passively mode-locked multiquantum well semiconductor laser subject to dual cavity optical self-feedback
Monolithic passively mode-locked (PML) semiconductor lasers with multi-GHz repetition rate (RR) emitting at wavelengths of around 1070nm are attractive ultrafast sources for seeding ytterbium doped fiber amplifiers and for photonic communication at high data rates. The timing stability quantified by the timing jitter (TJ) and the RR tuning range of a PML multi quantum-well (QW) semiconductor laser emitting at 1070nm subject to dual-cavity optical self-feedback (DC-OFB) consisting of one very short cavity for a high RR tuning range and one very long cavity for strong TJ reduction is investigated. The 3mm long PML QW semiconductor laser with a saturable absorber section length of 10% of the total cavity length has a RR of 13.61 GHz and a TJ of 83 fs with a pulse width amounting to 8 ps at the investigated injected gain current, absorber reverse bias voltage and cooling block temperature. For the combination of the long fiber-based cavity amounting to 5.9m combined with the short free-space cavity amounting to a few laser cavity lengths a RR tuning range over 1 GHz is achieved. Furthermore a minimal TJ of approximately 330 as with full sideband suppression in the radio-frequency (RF) spectrum is achieved which is an improvement by factor 250 in comparison to the free-running laser.
- 9 May 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10682, 106821Z
Timing stability and repetition rate frequency tuning analysis of a passively mode-locked multiquantum well semiconductor laser subject to dual cavity optical self-feedback
Monolithic passively mode-locked (PML) semiconductor lasers with multi-GHz repetition rate (RR) emitting at wavelengths of around 1070nm are attractive ultrafast sources for seeding ytterbium doped fiber amplifiers and for photonic communication at high data rates. The timing stability quantified by the timing jitter (TJ) and the RR tuning range of a PML multi quantum-well (QW) semiconductor laser emitting at 1070nm subject to dual-cavity optical self-feedback (DC-OFB) consisting of one very short cavity for a high RR tuning range and one very long cavity for strong TJ reduction is investigated. The 3mm long PML QW semiconductor laser with a saturable absorber section length of 10% of the total cavity length has a RR of 13.61 GHz and a TJ of 83 fs with a pulse width amounting to 8 ps at the investigated injected gain current, absorber reverse bias voltage and cooling block temperature. For the combination of the long fiber-based cavity amounting to 5.9m combined with the short free-space cavity amounting to a few laser cavity lengths a RR tuning range over 1 GHz is achieved. Furthermore a minimal TJ of approximately 330 as with full sideband suppression in the radio-frequency (RF) spectrum is achieved which is an improvement by factor 250 in comparison to the free-running laser.
- 9 May 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10682, 106820N
Mode-locked diode laser with resonant ring amplifier
We present a ring semiconductor amplifier system which is seeded by ultrashort pulses for additive amplification. An external cavity diode laser configuration is built to generate the ultrashort pulses based on a hybrid modelocking scheme. A monolithic multi-segment diode laser is utilized as a light source in the operating oscillator. It has the advantage that the gain and absorber are integrated on one chip. The oscillator operates at a fundamental repetition-rate of 206MHz and can be driven on various harmonics of this frequency. The generated pulses are injected into a tapered amplifier (TA) which consists of a ridge waveguide section (RWS) for coupling and a tapered section (TS) for amplification. The amplified pulses are coupled back after amplification towards the TAs RWS forming a ring resonator setup. By matching the cavity lengths of the oscillator and ring resonator, we can obtain additively amplified pulses. The emission spectrum of the chosen TA is centered around 850nm which is in the wavelength range of the oscillator. The spectrum of the additively amplified pulses is observed for different pumping parameters of the TA using an optical spectrum analyzer. Additionally, we characterized the system for the best seeding parameters by monitoring the output signal with an autocorrelator. We figured out that the best performance is achieved when the amplifier is seeded by pulses at the second harmonic of 412 MHz. When blocking the seeding pulses the amplifier operates in continuous wave (CW) regime. By comparing the obtained spectra for CW and additively amplified pulses, we conclude that the system operates with a CW background also in pulsed operation. However, from the comparison of the spectra, we estimate that the amplified pulsed power is about 120mW for a seed power of 1:1mW. Thus, the ring amplifier provides a significantly higher amplification than a single pass amplifier. In future work the CW background has to be suppressed, e.g. by synchronous modulation of the current into the amplifiers ridge waveguide section.
- 9 May 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10682, 106820N
Mode-locked diode laser with resonant ring amplifier
We present a ring semiconductor amplifier system which is seeded by ultrashort pulses for additive amplification. An external cavity diode laser configuration is built to generate the ultrashort pulses based on a hybrid modelocking scheme. A monolithic multi-segment diode laser is utilized as a light source in the operating oscillator. It has the advantage that the gain and absorber are integrated on one chip. The oscillator operates at a fundamental repetition-rate of 206MHz and can be driven on various harmonics of this frequency. The generated pulses are injected into a tapered amplifier (TA) which consists of a ridge waveguide section (RWS) for coupling and a tapered section (TS) for amplification. The amplified pulses are coupled back after amplification towards the TAs RWS forming a ring resonator setup. By matching the cavity lengths of the oscillator and ring resonator, we can obtain additively amplified pulses. The emission spectrum of the chosen TA is centered around 850nm which is in the wavelength range of the oscillator. The spectrum of the additively amplified pulses is observed for different pumping parameters of the TA using an optical spectrum analyzer. Additionally, we characterized the system for the best seeding parameters by monitoring the output signal with an autocorrelator. We figured out that the best performance is achieved when the amplifier is seeded by pulses at the second harmonic of 412 MHz. When blocking the seeding pulses the amplifier operates in continuous wave (CW) regime. By comparing the obtained spectra for CW and additively amplified pulses, we conclude that the system operates with a CW background also in pulsed operation. However, from the comparison of the spectra, we estimate that the amplified pulsed power is about 120mW for a seed power of 1:1mW. Thus, the ring amplifier provides a significantly higher amplification than a single pass amplifier. In future work the CW background has to be suppressed, e.g. by synchronous modulation of the current into the amplifiers ridge waveguide section.
- 7 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 54 (3) , 1-9
Picosecond Pulse Generation and Pulse Train Stability of A Monolithic Passively Mode-Locked Semiconductor Quantum-Well Laser at 1070 nm
We experimentally study the pulse generation and the pulse train timing and amplitude stability of a monolithic passively mode-locked multisection quantum-well semiconductor laser. The laser emits a stable optical pulse train at a wavelength of 1070 nm and at a fundamental repetition rate of 20 GHz. Timing jitter and amplitude jitter analysis allows identifying distinct laser operating regimes of stable picosecond optical pulses. We obtain an ultra-low pulse-to-pulse timing jitter of 22 fs and find emission regimes which are unaffected by amplitude jitter. The lowest pulse width amounts to 2.6 ps, and the highest pulse peak power is estimated to be 556 mW at a low timing jitter of 170 fs and a negligible relative amplitude jitter of 0.05.
- 7 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 54 (3) , 1-9
Picosecond Pulse Generation and Pulse Train Stability of A Monolithic Passively Mode-Locked Semiconductor Quantum-Well Laser at 1070 nm
We experimentally study the pulse generation and the pulse train timing and amplitude stability of a monolithic passively mode-locked multisection quantum-well semiconductor laser. The laser emits a stable optical pulse train at a wavelength of 1070 nm and at a fundamental repetition rate of 20 GHz. Timing jitter and amplitude jitter analysis allows identifying distinct laser operating regimes of stable picosecond optical pulses. We obtain an ultra-low pulse-to-pulse timing jitter of 22 fs and find emission regimes which are unaffected by amplitude jitter. The lowest pulse width amounts to 2.6 ps, and the highest pulse peak power is estimated to be 556 mW at a low timing jitter of 170 fs and a negligible relative amplitude jitter of 0.05.
- 24 March 2017
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 32 (4) , 045016
Electro-optical characteristics of 808 nm ridge-waveguide lasers operated with high-current nanosecond pulses
The aim of this paper is to present detailed experimental and theoretical investigations of the behavior of ridge-waveguide (RW) lasers emitting at 808 nm under injection of 3 ns long current pulses with amplitudes higher than 10 A. The RW lasers are based on tensile-strained GaAsP quantum wells embedded in asymmetric and extremely asymmetric AlGaAs based waveguide structures, which differ mainly in the ratio between the thicknesses of the p- and n-type confinement layers. The width of the ridges is 4.4 μ m and the length of the cavities is 3.9 mm. The laser diodes are mounted on an in-house developed high-frequency unit electrically driven by nearly rectangular shaped current pulses with a length of 3 ns and a repetition frequency of 1 MHz. At a pulse current of 15 A maximum pulse powers of 4.0 and 5.4 W are reached for the asymmetric and extremely asymmetric structures, respectively. After turning off the bias a pronounced negative current superimposed by current oscillations caused by the external circuitry appears. Two-dimensional simulations based on a solution of the time-dependent drift-diffusion, waveguide and power-balance equations reveal that a part of the carriers injected into the laser diode does not recombine in the active region and accumulates under the ridge in the bulk layers and beyond the ridge in the active layer. At the end of the electrical pulse the electrons flow back and generate a reverse (negative) current. The simulation exaggerates the achievable output power, in particular for the extremely asymmetric structure. Further theoretical studies are needed to resolve this discrepancy.
- 24 March 2017
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 32 (4) , 045016
Electro-optical characteristics of 808 nm ridge-waveguide lasers operated with high-current nanosecond pulses
The aim of this paper is to present detailed experimental and theoretical investigations of the behavior of ridge-waveguide (RW) lasers emitting at 808 nm under injection of 3 ns long current pulses with amplitudes higher than 10 A. The RW lasers are based on tensile-strained GaAsP quantum wells embedded in asymmetric and extremely asymmetric AlGaAs based waveguide structures, which differ mainly in the ratio between the thicknesses of the p- and n-type confinement layers. The width of the ridges is 4.4 μ m and the length of the cavities is 3.9 mm. The laser diodes are mounted on an in-house developed high-frequency unit electrically driven by nearly rectangular shaped current pulses with a length of 3 ns and a repetition frequency of 1 MHz. At a pulse current of 15 A maximum pulse powers of 4.0 and 5.4 W are reached for the asymmetric and extremely asymmetric structures, respectively. After turning off the bias a pronounced negative current superimposed by current oscillations caused by the external circuitry appears. Two-dimensional simulations based on a solution of the time-dependent drift-diffusion, waveguide and power-balance equations reveal that a part of the carriers injected into the laser diode does not recombine in the active region and accumulates under the ridge in the bulk layers and beyond the ridge in the active layer. At the end of the electrical pulse the electrons flow back and generate a reverse (negative) current. The simulation exaggerates the achievable output power, in particular for the extremely asymmetric structure. Further theoretical studies are needed to resolve this discrepancy.
- 7 March 2016
- Published by SPIE-Intl Soc Optical Eng
- p. 97670N-97670N-6
Timing jitter performance of mode-locked external cavity multi-quantum-well semiconductor lasers
- 7 March 2016
- Published by SPIE-Intl Soc Optical Eng
- p. 97670N-97670N-6
Timing jitter performance of mode-locked external cavity multi-quantum-well semiconductor lasers
- 7 March 2016
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9767, 976705-976705-12
Generation of 7W nanosecond pulses with 670nm ridge-waveguide lasers
- 7 March 2016
- Published by SPIE-Intl Soc Optical Eng
- Vol. 9767, 976705-976705-12
Generation of 7W nanosecond pulses with 670nm ridge-waveguide lasers