S. Jithin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
S. Jithin has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Sadhana Joshi
School of Management, Doon University, Dehradun, India
6 shared publications Upendra V. Bhandarkar
5 shared publicationsSuhas S. Joshi
3 shared publications- Ajinkya Raut
J. Mike Walker ’66 Department of Mechanical Engineering Texas A&M University College Station TX 77843 USA
2 shared publications - Upendra V. Bhandarkar
Indian Institute of Technology Bombay
2 shared publications Jewel J. Rodrigues
Department of Mechanical Engineering, Veermata Jijabai Technological Institute, Mumbai, India
1 shared publication
Latest Publications
- 1 December 2021
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 298
Surface topography generation and simulation in electrical discharge texturing: A review
- 1 December 2021
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 298
Surface topography generation and simulation in electrical discharge texturing: A review
- 1 December 2020
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 60, 384-399
Three-dimensional topography analysis of electrical discharge textured SS304 surfaces
- 1 December 2020
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 60, 384-399
Three-dimensional topography analysis of electrical discharge textured SS304 surfaces
- 5 November 2020
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 8 (4) , 045018
Characterization of Surface Topographies Generated using Circular- and Cylindrical-Face EDT
Large area texturing using EDT is challenging due to surface damage resulted from inefficient discharges, such as arcs and short-circuits. Also, three-dimensional analyses of surface topography generated during electrical discharge texturing (EDT) are scarcely performed in the available literature. Therefore, in this work, two modes of EDT were developed for large area texturing based on the mode of electrode movement resulting in texture generation on work surfaces: circular-face EDT (CirEDT) and cylindrical-face EDT (CylEDT), and the generated surface topographies are characterized in terms of topography images, areal texture parameters, and scanning electron microscopy images. Parametric analyses are also performed to study the influences of the operating parameters, such as discharge current, pulse on-time, and peripheral velocity, on different areal texture parameters. Topography analyses reveal that these surfaces have a characteristic stochastic distribution of microstructures in shape, size, and location. Height parameter analyses reveal that CylEDT surfaces are twice positively skewed and have a higher kurtosis as compared to the CirEDT surfaces. Spatial parameter analyses reveal that both surfaces display dominance of isotropic nature and non-directional structures. CirEDT surfaces have higher lubricant retention capacity, but lesser wear volume available for running-in period as compared to CylEDT surfaces, as per volume parameter analyses. Discharge current and pulse on-time are identified as the significant parameters influencing the majority of the areal texture parameters analyzed. SEM analysis revealed that CylEDT results in a textured surface with sea-wave-like structures, whereas CirEDT results in a textured surface with lunar-craters-like structures.
- 5 November 2020
- Published by IOP Publishing in Surface Topography: Metrology and Properties
- Vol. 8 (4) , 045018
Characterization of Surface Topographies Generated using Circular- and Cylindrical-Face EDT
Large area texturing using EDT is challenging due to surface damage resulted from inefficient discharges, such as arcs and short-circuits. Also, three-dimensional analyses of surface topography generated during electrical discharge texturing (EDT) are scarcely performed in the available literature. Therefore, in this work, two modes of EDT were developed for large area texturing based on the mode of electrode movement resulting in texture generation on work surfaces: circular-face EDT (CirEDT) and cylindrical-face EDT (CylEDT), and the generated surface topographies are characterized in terms of topography images, areal texture parameters, and scanning electron microscopy images. Parametric analyses are also performed to study the influences of the operating parameters, such as discharge current, pulse on-time, and peripheral velocity, on different areal texture parameters. Topography analyses reveal that these surfaces have a characteristic stochastic distribution of microstructures in shape, size, and location. Height parameter analyses reveal that CylEDT surfaces are twice positively skewed and have a higher kurtosis as compared to the CirEDT surfaces. Spatial parameter analyses reveal that both surfaces display dominance of isotropic nature and non-directional structures. CirEDT surfaces have higher lubricant retention capacity, but lesser wear volume available for running-in period as compared to CylEDT surfaces, as per volume parameter analyses. Discharge current and pulse on-time are identified as the significant parameters influencing the majority of the areal texture parameters analyzed. SEM analysis revealed that CylEDT results in a textured surface with sea-wave-like structures, whereas CirEDT results in a textured surface with lunar-craters-like structures.
- 7 January 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 106 (9-10) , 3741-3758
Multi-spark model for predicting surface roughness of electrical discharge textured surfaces
- 7 January 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 106 (9-10) , 3741-3758
Multi-spark model for predicting surface roughness of electrical discharge textured surfaces
- 1 December 2019
- Published by Springer Nature
- p. 731-740
Establishing EDM as a Method for Inducing Hydrophobicity on SS 304 Surfaces
- 1 December 2019
- Published by Springer Nature
- p. 731-740
Establishing EDM as a Method for Inducing Hydrophobicity on SS 304 Surfaces
- 14 March 2018
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 4 (3) , 466-479
Analysis of electrical discharge texturing using different electrode materials
Electrical discharge texturing (EDT) is used to generate rough surface textures. Though roughness of the work surface obtained through EDM has been studied, surface textures obtained have not been paid attention to so far. Stainless steel 316L samples were textured using tool materials, such as copper (Cu), tungsten (W) and copper–tungsten (Cu–W) while varying operating parameters such as gap voltage and pulse on-time. At low levels of operating parameters, due to high tool wear of copper, a lesser number of surface irregularities such as micro-globules and micro-cracks were observed on the textured surfaces compared to those displayed by other electrodes. However, at high levels of operating parameters, the anodic erosion on the tool becomes constant, which leads to a denser distribution of surface irregularities due to high electrical discharge efficiency. Tungsten electrode with low electrical discharge efficiency and low tool wear shows an opposite trend. Copper–tungsten electrode with high electrical discharge efficiency and low tool wear leads to a denser distribution of surface irregularities at both low and high levels of operating parameters. Evaluation of a few samples textured with copper electrode showed good protein adhesion, whereas the polished sample did not display any protein adhesion.
- 14 March 2018
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 4 (3) , 466-479
Analysis of electrical discharge texturing using different electrode materials
Electrical discharge texturing (EDT) is used to generate rough surface textures. Though roughness of the work surface obtained through EDM has been studied, surface textures obtained have not been paid attention to so far. Stainless steel 316L samples were textured using tool materials, such as copper (Cu), tungsten (W) and copper–tungsten (Cu–W) while varying operating parameters such as gap voltage and pulse on-time. At low levels of operating parameters, due to high tool wear of copper, a lesser number of surface irregularities such as micro-globules and micro-cracks were observed on the textured surfaces compared to those displayed by other electrodes. However, at high levels of operating parameters, the anodic erosion on the tool becomes constant, which leads to a denser distribution of surface irregularities due to high electrical discharge efficiency. Tungsten electrode with low electrical discharge efficiency and low tool wear shows an opposite trend. Copper–tungsten electrode with high electrical discharge efficiency and low tool wear leads to a denser distribution of surface irregularities at both low and high levels of operating parameters. Evaluation of a few samples textured with copper electrode showed good protein adhesion, whereas the polished sample did not display any protein adhesion.
- Open Access
- 1 January 2018
- Published by Elsevier in Procedia Manufacturing
- Vol. 26, 617-628
FE Modeling for Single Spark in EDM Considering Plasma Flushing Efficiency
- 1 January 2018
- Published by Elsevier in Procedia Manufacturing
- Vol. 26, 617-628
Open AccessFE Modeling for Single Spark in EDM Considering Plasma Flushing Efficiency
- 13 September 2017
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 139 (11) , 111002
Analytical Simulation of Random Textures Generated in Electrical Discharge Texturing
Textured functional surfaces are finding applications in the fields of bioengineering, surface energy, hydrodynamics, lubrication, and optics. Electrical discharge machining (EDM), which is normally used to generate smoother surface finish on various automotive components and toolings, can also generate surfaces of rough finish, a desirable characteristic for texturing purposes. There is a lack of modeling efforts to predict the surface textures obtained under various EDM operating conditions. The aim of the current work is to capture the physics of the electrical discharge texturing (EDT) on a surface assuming random generation of multiple sparks with respect to (i) space, (ii) time, and (iii) energy. A uniform heat disk assumption is taken for each individual spark. The three-dimensional (3D) texture generated is utilized to evaluate a 3D roughness parameter namely arithmetic mean height, . Surface textures obtained from the model are validated against experimentally obtained ones by comparison of distribution of values taken along parallel sections along the surface. It was found that the distribution of simulated values agrees with that of experimental values.- 13 September 2017
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 139 (11) , 111002
Analytical Simulation of Random Textures Generated in Electrical Discharge Texturing
Textured functional surfaces are finding applications in the fields of bioengineering, surface energy, hydrodynamics, lubrication, and optics. Electrical discharge machining (EDM), which is normally used to generate smoother surface finish on various automotive components and toolings, can also generate surfaces of rough finish, a desirable characteristic for texturing purposes. There is a lack of modeling efforts to predict the surface textures obtained under various EDM operating conditions. The aim of the current work is to capture the physics of the electrical discharge texturing (EDT) on a surface assuming random generation of multiple sparks with respect to (i) space, (ii) time, and (iii) energy. A uniform heat disk assumption is taken for each individual spark. The three-dimensional (3D) texture generated is utilized to evaluate a 3D roughness parameter namely arithmetic mean height, . Surface textures obtained from the model are validated against experimentally obtained ones by comparison of distribution of values taken along parallel sections along the surface. It was found that the distribution of simulated values agrees with that of experimental values.