OndřEj Hanuš
Research Subjects
OndřEj Hanuš has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Jan Mikeš
Czech Technical University in Prague,Faculty of Electrical Engineering,Prague,Czech Republic
7 shared publications - Stanislav Pekárek
Faculty of Electrical Engineering, Czech Technical University in Prague, Prague, Czech Republic
4 shared publications - Ivan Soukup
Faculty of Electrical Engineering, Czech Technical University in Prague, Technická 2, 166 27 Prague, Czech Republic
2 shared publications - Marcela Efmertová
Historical Laboratory of (Electro)Technology, Faculty of Electrical Engineering, Czech Technical University in Prague, Technická 2, Prague 6, 166 27, Czech Republic
2 shared publications - Jakub Kákona
Czech Technical University in Prague, Faculty of Electrical Engineering, Technicka 2, 166 27 Prague, Czech Republic
1 shared publication - Martin Mydlář
HiLASE Centre, Institute of Physics, Academy of Sciences of the Czech Republic,Doln Beany,Czech Republic
1 shared publication
Latest Publications
- 2 September 2026
- Published by Elsevier in Electric Power Systems Research
- Vol. 265
Lightning geolocation accuracy as the dominant error source in evaluating strike-prediction models for transmission lines
- 2 September 2026
- Published by Elsevier in Electric Power Systems Research
- Vol. 265
Lightning geolocation accuracy as the dominant error source in evaluating strike-prediction models for transmission lines
- 17 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 423-428
The Dynamics of Laser-Driven Ionisation in High-Voltage Circuit Switching
This study explores the use of laser-induced ionisation for triggering high-voltage (HV) discharges offers a precise, non-invasive alternative to conventional spark gap methods. Conducted at the HiLASE Centre using an advanced picosecond laser system, the research investigates how laser parameters — including wavelength, pulse energy, and irradiance — affect air breakdown voltage and discharge delay. Experimental results show that focused ultrafast laser pulses can significantly reduce the breakdown voltage, with reductions up to 30%, depending on wavelength and gap distance. Moreover, the delay between laser pulse and breakdown decreases with higher irradiance, particularly at lower voltages where exponential delay trends were observed. These findings confirm the efficacy of quantum ionisation in air and demonstrate the potential of laser-assisted triggering for fast and reliable HV switching. The ability to tailor breakdown characteristics through laser control opens new possibilities for advanced plasma applications, precision circuit protection, and high-speed switching technologies.
- 17 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 423-428
The Dynamics of Laser-Driven Ionisation in High-Voltage Circuit Switching
This study explores the use of laser-induced ionisation for triggering high-voltage (HV) discharges offers a precise, non-invasive alternative to conventional spark gap methods. Conducted at the HiLASE Centre using an advanced picosecond laser system, the research investigates how laser parameters — including wavelength, pulse energy, and irradiance — affect air breakdown voltage and discharge delay. Experimental results show that focused ultrafast laser pulses can significantly reduce the breakdown voltage, with reductions up to 30%, depending on wavelength and gap distance. Moreover, the delay between laser pulse and breakdown decreases with higher irradiance, particularly at lower voltages where exponential delay trends were observed. These findings confirm the efficacy of quantum ionisation in air and demonstrate the potential of laser-assisted triggering for fast and reliable HV switching. The ability to tailor breakdown characteristics through laser control opens new possibilities for advanced plasma applications, precision circuit protection, and high-speed switching technologies.
- Open Access
- 22 January 2025
- Published by Elsevier in Electrochemistry Communications
- Vol. 172
Combined effects of electrode geometry and airflow streamlines patterns on ozone production of a cylindrical dielectric barrier discharge
- 22 January 2025
- Published by Elsevier in Electrochemistry Communications
- Vol. 172
Open AccessCombined effects of electrode geometry and airflow streamlines patterns on ozone production of a cylindrical dielectric barrier discharge
- 29 December 2021
- Published by Taylor & Francis in Ozone: Science & Engineering
- Vol. 45 (1) , 2-18
Surface Dielectric Barrier Discharge in a Cylindrical Configuration – Effect of Airflow Orientation to the Microdischarges
This paper is devoted to studying the effect of airflow orientation on the microdischarges of the surface dielectric barrier discharge in cylindrical configuration through varying air input into the discharge chamber, the number of input nozzles, and the geometry of the active electrode. The air is supplied into the discharge chamber tangentially, radially, or axially through one or four input nozzles. Air input into the discharge chamber and the number of input nozzles determine the airflow regime. We used two active electrode geometries that are the axial strips or azimuthal rings. The change of active electrode geometry from rings to strips affects the orientation of microdischarges with respect to the airflow. For the discharge, the variation of air inputs and the number of input nozzles influences the flow regime in the discharge chamber, which, together with the active electrode geometry, affects the temperature field distribution in the chamber. These factors play an important role in plasmachemical processes leading to the discharge generation of various species, such as ozone. It is found that, for the maximum effect of airflow on discharge ozone generation, the streamlines should be uniformly distributed in the discharge chamber and predominantly oriented perpendicular to the majority of microdischarges.
- 29 December 2021
- Published by Taylor & Francis in Ozone: Science & Engineering
- Vol. 45 (1) , 2-18
Surface Dielectric Barrier Discharge in a Cylindrical Configuration – Effect of Airflow Orientation to the Microdischarges
This paper is devoted to studying the effect of airflow orientation on the microdischarges of the surface dielectric barrier discharge in cylindrical configuration through varying air input into the discharge chamber, the number of input nozzles, and the geometry of the active electrode. The air is supplied into the discharge chamber tangentially, radially, or axially through one or four input nozzles. Air input into the discharge chamber and the number of input nozzles determine the airflow regime. We used two active electrode geometries that are the axial strips or azimuthal rings. The change of active electrode geometry from rings to strips affects the orientation of microdischarges with respect to the airflow. For the discharge, the variation of air inputs and the number of input nozzles influences the flow regime in the discharge chamber, which, together with the active electrode geometry, affects the temperature field distribution in the chamber. These factors play an important role in plasmachemical processes leading to the discharge generation of various species, such as ozone. It is found that, for the maximum effect of airflow on discharge ozone generation, the streamlines should be uniformly distributed in the discharge chamber and predominantly oriented perpendicular to the majority of microdischarges.
- 30 January 2021
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 41 (3) , 779-792
Air Supply Mode Effects on Ozone Production of Surface Dielectric Barrier Discharge in a Cylindrical Configuration
- 30 January 2021
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 41 (3) , 779-792
Air Supply Mode Effects on Ozone Production of Surface Dielectric Barrier Discharge in a Cylindrical Configuration
- 2 December 2019
- Published by Wiley in Plasma Processes and Polymers
- Vol. 17 (1)
3D printing materials for generators of active particles based on electrical discharges
In this study, we focus our attention on the impact of ozone (O3) and ultraviolet radiation (UV) on materials usable for three‐dimensional (3D) printing. Specifically, we have studied the potential degradative effect on the most commonly used filaments, such as polylactic acid (PLA) and acrylonitrile–butadiene–styrene (ABS). The effect has been examined on objects printed on a 3D printer and on the materials of discharge chambers of O3 generators from which they were printed. For the purpose of adequate assessment of the actual impact of O3 and UV, samples were monitored for a period of 18‐hr of exposure. The methods of Raman spectroscopy, optical and scanning electron microscopy and Fourier‐transform infrared spectroscopy (FTIR) have been employed for an objective evaluation of potential modifications. A generator equipped with a chamber printed from a new PLA filament and an active electrode system in the form of a stripes electrode, or more precisely, in the second case, a honeycomb‐active electrode, both cut out of a thin copper foil, was used for the generation of O3 and UV radiation. The tested materials showed substantial resistance to O3 exposure under the test conditions. The result of measurements suggested that these materials could be used for chambers for the O3 as well as for active particle generation.
- 2 December 2019
- Published by Wiley in Plasma Processes and Polymers
- Vol. 17 (1)
3D printing materials for generators of active particles based on electrical discharges
In this study, we focus our attention on the impact of ozone (O3) and ultraviolet radiation (UV) on materials usable for three‐dimensional (3D) printing. Specifically, we have studied the potential degradative effect on the most commonly used filaments, such as polylactic acid (PLA) and acrylonitrile–butadiene–styrene (ABS). The effect has been examined on objects printed on a 3D printer and on the materials of discharge chambers of O3 generators from which they were printed. For the purpose of adequate assessment of the actual impact of O3 and UV, samples were monitored for a period of 18‐hr of exposure. The methods of Raman spectroscopy, optical and scanning electron microscopy and Fourier‐transform infrared spectroscopy (FTIR) have been employed for an objective evaluation of potential modifications. A generator equipped with a chamber printed from a new PLA filament and an active electrode system in the form of a stripes electrode, or more precisely, in the second case, a honeycomb‐active electrode, both cut out of a thin copper foil, was used for the generation of O3 and UV radiation. The tested materials showed substantial resistance to O3 exposure under the test conditions. The result of measurements suggested that these materials could be used for chambers for the O3 as well as for active particle generation.