Xiaolong Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xiaolong Liu has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Howard Cam Luong
Department of Electronic and Computer Engineering, The Hong Kong University of Science and Technology, Sai Kung, Hong Kong
7 shared publications - Hanzhang Cao
Nanjing University of Science and Technology
4 shared publications - Tongde Huang
Nanjing University of Science and Technology
4 shared publications - Wen Wu
Nanjing University of Science and Technology
4 shared publications Kaitian Yang
Southern University of Science and Technology
3 shared publicationsChufan Li
Nanjing University of Science and Technology
2 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (11) , 7343-7355
A 27-GHz Magnetic-Isolated Sub-Sampling PLL With a Fast-Locking Controller Achieving 64.9-fs Jitter and −69.1-dBc Reference Spur
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (11) , 7343-7355
A 27-GHz Magnetic-Isolated Sub-Sampling PLL With a Fast-Locking Controller Achieving 64.9-fs Jitter and −69.1-dBc Reference Spur
- 28 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 1876-1894
A 19.4-fs RMS Jitter 0.1-to-44-GHz Cryo-CMOS Fractional- N CP-PLL Featuring Automatic Bleed Calibration for Quantum Computing
Cryogenic fractional-$N$ phase-locked loops (PLLs) are essential for large-scale superconducting quantum computing, and serve as integrated pump sources for Josephson parametric amplifiers. These PLLs enable high-fidelity qubit readout while reducing the thermal load and wiring complexity associated with room-temperature generators. However, the cryogenic pump sources developed thus far were unable to meet the stringent phase noise and frequency agility requirements for high-fidelity qubit readout. In this study, we present a cryo-CMOS fractional-$N$ charge-pump PLL (CP-PLL) operating over a range of 4–300 K that provides low-noise, multi-frequency pump and clock signals. We proposed an automatic bleed calibration (ABC) technique to mitigate the folding effect of the delta-sigma ($\Delta \Sigma $ ) modulator residue through phase-frequency detector (PFD) and CP nonidealities. This approach helps in detecting PFD pulsewidth asymmetry and digitally optimizing the bleed current, thereby minimizing both the reference and fractional spurs. The proposed prototype was fabricated via a 28-nm CMOS process and synthesizes signals ranging from 0.1 to 44 GHz using on-chip dividers and multipliers. At 4 K, it achieves integrated jitter (12 kHz–20 MHz) of 19.4 fs under a frequency of 8.6 GHz, with reference spurs below −71 dBc and fractional-spur suppression of up to 40 dB when ABC is enabled. At 300 K, the proposed CP-PLL achieves a jitter of 29.7 fs under a frequency of 8.6 GHz with a reference spur of −82 dBc. To the best of our knowledge, this represents the lowest jitter reported for a cryo-CMOS fractional-$N$ CP-PLL in the literature.- 28 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (5) , 1876-1894
A 19.4-fs RMS Jitter 0.1-to-44-GHz Cryo-CMOS Fractional- N CP-PLL Featuring Automatic Bleed Calibration for Quantum Computing
Cryogenic fractional-$N$ phase-locked loops (PLLs) are essential for large-scale superconducting quantum computing, and serve as integrated pump sources for Josephson parametric amplifiers. These PLLs enable high-fidelity qubit readout while reducing the thermal load and wiring complexity associated with room-temperature generators. However, the cryogenic pump sources developed thus far were unable to meet the stringent phase noise and frequency agility requirements for high-fidelity qubit readout. In this study, we present a cryo-CMOS fractional-$N$ charge-pump PLL (CP-PLL) operating over a range of 4–300 K that provides low-noise, multi-frequency pump and clock signals. We proposed an automatic bleed calibration (ABC) technique to mitigate the folding effect of the delta-sigma ($\Delta \Sigma $ ) modulator residue through phase-frequency detector (PFD) and CP nonidealities. This approach helps in detecting PFD pulsewidth asymmetry and digitally optimizing the bleed current, thereby minimizing both the reference and fractional spurs. The proposed prototype was fabricated via a 28-nm CMOS process and synthesizes signals ranging from 0.1 to 44 GHz using on-chip dividers and multipliers. At 4 K, it achieves integrated jitter (12 kHz–20 MHz) of 19.4 fs under a frequency of 8.6 GHz, with reference spurs below −71 dBc and fractional-spur suppression of up to 40 dB when ABC is enabled. At 300 K, the proposed CP-PLL achieves a jitter of 29.7 fs under a frequency of 8.6 GHz with a reference spur of −82 dBc. To the best of our knowledge, this represents the lowest jitter reported for a cryo-CMOS fractional-$N$ CP-PLL in the literature.- 12 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (12) , 10336-10346
A 22.4-to-35-GHz Two-Stage Low-Noise Amplifier With Triple-Coupled Transformer-Based Input Matching Technique in 65-nm CMOS
This article presents the analysis and design of a two-stage low-noise amplifier (LNA) with enhanced wideband input matching bandwidth and a low flat noise figure (NF) across the entire operating range. A compact triple-coupled transformer-based input power matching network is proposed to facilitate broadband input and noise matching simultaneously. In addition, by accounting for the loading effect of the interstage magnetically coupled resonator (MCR), a third peak of input impedance is achieved for further bandwidth extension. Designed and fabricated in a 65-nm CMOS process, the proposed LNA achieves a 3-dB bandwidth from 22.4 to 35 GHz with a gain of 12.0 dB. The 10-dB input return loss bandwidth is 33.7 GHz, spanning from 14.9 to 48.6 GHz. The measured NF is between 2.7 and 3.2 dB, and the input 1-dB gain compression point (IP1dB) ranges from −12.5 to −10.6 dBm. The measured third-order input intercept point (IIP3) is −0.7 dBm at 28 GHz. The LNA consumes 11.3 mW and occupies a core area of 0.15 mm2.
- 12 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (12) , 10336-10346
A 22.4-to-35-GHz Two-Stage Low-Noise Amplifier With Triple-Coupled Transformer-Based Input Matching Technique in 65-nm CMOS
This article presents the analysis and design of a two-stage low-noise amplifier (LNA) with enhanced wideband input matching bandwidth and a low flat noise figure (NF) across the entire operating range. A compact triple-coupled transformer-based input power matching network is proposed to facilitate broadband input and noise matching simultaneously. In addition, by accounting for the loading effect of the interstage magnetically coupled resonator (MCR), a third peak of input impedance is achieved for further bandwidth extension. Designed and fabricated in a 65-nm CMOS process, the proposed LNA achieves a 3-dB bandwidth from 22.4 to 35 GHz with a gain of 12.0 dB. The 10-dB input return loss bandwidth is 33.7 GHz, spanning from 14.9 to 48.6 GHz. The measured NF is between 2.7 and 3.2 dB, and the input 1-dB gain compression point (IP1dB) ranges from −12.5 to −10.6 dBm. The measured third-order input intercept point (IIP3) is −0.7 dBm at 28 GHz. The LNA consumes 11.3 mW and occupies a core area of 0.15 mm2.
- 2 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (1) , 87-99
A Class-F 23 CMOS Oscillator With Second and Third Harmonic Resonances Expansion
This paper presents a class-F23 voltage-controlled oscillator (VCO) designed to improve phase noise performance through harmonic shaping while suppressing the flicker and white noise upconversion without manual 2nd or 3rd harmonic tuning. By leveraging a three-coil transformer-based resonator, the design achieves differential-mode (DM) resonance expansion at the 3rd harmonic frequency while maintaining the class-F operation. This approach eliminates the need for a low-quality (Q) factor switched-capacitor array (SCA) for 1st-to-3rd harmonic alignment, thereby improving the tank’s Q. Additionally, a two-coil transformer-based resonator is employed for tail filtering, enabling wideband common-mode (CM) resonance at the 2nd harmonic frequency, which helps to nullify flicker noise and prevent tank Q degradation due to the differential pair operating in the triode region. Implemented in a 65-nm CMOS process, the proposed prototype achieves a frequency tuning range from 18.5 to 22.4 GHz, phase noise from −110.7 to −106.1 dBc/Hz at 1-MHz offset, while consuming 5 mW and occupying a compact core area of 0.061 mm2, corresponding to a peak figure-of-merit (FoM) of 189.1 dBc/Hz and FoMT of 194.7 dBc/Hz.
- 2 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 73 (1) , 87-99
A Class-F 23 CMOS Oscillator With Second and Third Harmonic Resonances Expansion
This paper presents a class-F23 voltage-controlled oscillator (VCO) designed to improve phase noise performance through harmonic shaping while suppressing the flicker and white noise upconversion without manual 2nd or 3rd harmonic tuning. By leveraging a three-coil transformer-based resonator, the design achieves differential-mode (DM) resonance expansion at the 3rd harmonic frequency while maintaining the class-F operation. This approach eliminates the need for a low-quality (Q) factor switched-capacitor array (SCA) for 1st-to-3rd harmonic alignment, thereby improving the tank’s Q. Additionally, a two-coil transformer-based resonator is employed for tail filtering, enabling wideband common-mode (CM) resonance at the 2nd harmonic frequency, which helps to nullify flicker noise and prevent tank Q degradation due to the differential pair operating in the triode region. Implemented in a 65-nm CMOS process, the proposed prototype achieves a frequency tuning range from 18.5 to 22.4 GHz, phase noise from −110.7 to −106.1 dBc/Hz at 1-MHz offset, while consuming 5 mW and occupying a compact core area of 0.061 mm2, corresponding to a peak figure-of-merit (FoM) of 189.1 dBc/Hz and FoMT of 194.7 dBc/Hz.
- 9 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (8) , 2118-2131
A Trifilar Transformer-Based Class-F23 VCO With Noise-Circulating Technology
This article presents a low-phase noise (PN) trifilar transformer-based Class-F23 voltage-controlled oscillator (VCO) with noise-circulating technology. The topology minimizes the side effect of the parasitic capacitors that incorporates an uncontrollable common-mode (CM) path in the conventional noise-circulating VCOs, and reduces the magnitude of the noise sources injected into the tank by simultaneously switching on/off the source degeneration. Additionally, the PN is reduced because the proposed trifilar transformer-based tank can provide extra drain-to-gate gain. The proof-of-concept prototype is a 5.2–6.1GHz VCO in 65 nm CMOS. It exhibits a −146.6 dBc/Hz PN at 10 MHz offset, consuming 7.92 mW from a 0.9 V power supply at 5.9 GHz. The corresponding figure of merit (FoM) at 10MHz offset is 193 dBc/Hz. It achieves a slight supply frequency pushing of 13.3 and −18.7 MHz/V at the lowest and highest frequency, respectively. The occupied compact core area is 0.12mm2.
- 9 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (8) , 2118-2131
A Trifilar Transformer-Based Class-F23 VCO With Noise-Circulating Technology
This article presents a low-phase noise (PN) trifilar transformer-based Class-F23 voltage-controlled oscillator (VCO) with noise-circulating technology. The topology minimizes the side effect of the parasitic capacitors that incorporates an uncontrollable common-mode (CM) path in the conventional noise-circulating VCOs, and reduces the magnitude of the noise sources injected into the tank by simultaneously switching on/off the source degeneration. Additionally, the PN is reduced because the proposed trifilar transformer-based tank can provide extra drain-to-gate gain. The proof-of-concept prototype is a 5.2–6.1GHz VCO in 65 nm CMOS. It exhibits a −146.6 dBc/Hz PN at 10 MHz offset, consuming 7.92 mW from a 0.9 V power supply at 5.9 GHz. The corresponding figure of merit (FoM) at 10MHz offset is 193 dBc/Hz. It achieves a slight supply frequency pushing of 13.3 and −18.7 MHz/V at the lowest and highest frequency, respectively. The occupied compact core area is 0.12mm2.
- 6 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (8) , 1242-1245
A 16.5–53.5 GHz Magnetically Tuned Transformer-Based Mode-Switching Injection-Locked Frequency Divider With 105.7% Locking Range
This letter presents a 16.5–53.5GHz magnetically tuned transformer-based mode-switching injection-locked frequency divider (ILFD) in 65-nm CMOS. The fourth-order resonant tank of the proposed ILFD incorporates a switchable inductor coil along with a switchable capacitor to achieve mode-switching, effectively realizing a wide locking range (LR) compared to that of a conventional eighth-order transformer, while maintaining a high input impedance. Additionally, peaking inductors are utilized to ensure start-up conditions and achieve low power consumption. The measured LR and relative bandwidth are 37GHz and 105.7%, respectively. The chip features a compact core area of 0.04 mm2 and consumes 1.62 mW from a 0.45 V supply, resulting in figure of merits (FoMs) of 22.8GHz/mW and 65.2%/mW.
- 6 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (8) , 1242-1245
A 16.5–53.5 GHz Magnetically Tuned Transformer-Based Mode-Switching Injection-Locked Frequency Divider With 105.7% Locking Range
This letter presents a 16.5–53.5GHz magnetically tuned transformer-based mode-switching injection-locked frequency divider (ILFD) in 65-nm CMOS. The fourth-order resonant tank of the proposed ILFD incorporates a switchable inductor coil along with a switchable capacitor to achieve mode-switching, effectively realizing a wide locking range (LR) compared to that of a conventional eighth-order transformer, while maintaining a high input impedance. Additionally, peaking inductors are utilized to ensure start-up conditions and achieve low power consumption. The measured LR and relative bandwidth are 37GHz and 105.7%, respectively. The chip features a compact core area of 0.04 mm2 and consumes 1.62 mW from a 0.45 V supply, resulting in figure of merits (FoMs) of 22.8GHz/mW and 65.2%/mW.
- 11 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (6) , 694-697
A 16.6-to-34.1 GHz Dual-Core Quad-Mode Oscillator Achieving 202.3 dBc/Hz FoMT in 65nm CMOS
This work presents a millimeter-wave (mm-wave) dual-core quad-mode oscillator incorporating a switch-less tertiary loop to extend the frequency tuning range (FTR) without introducing additional switch loss or parasitic. The design couples two identical transformer-based dual-band (low- and high-frequency) voltage-controlled oscillators (VCOs), which are configurable in either even or odd modes via mode switches. In the high- and low-frequency band, the switch-less tertiary loop functions as an open circuit in the even mode and a short circuit in the odd mode, enabling four distinct frequency modes. Fabricated in a 65-nm CMOS process, the proposed oscillator achieves an FTR from 16.6 to 34.1 GHz, with phase noise ranging from −122.4 to −130.0 dBc/Hz at a 10-MHz offset, while consuming 9.5–11mW of power. This results in a peak FoM of 185.5 dBc/Hz and FoMT of 202.3 dBc/Hz.
- 11 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (6) , 694-697
A 16.6-to-34.1 GHz Dual-Core Quad-Mode Oscillator Achieving 202.3 dBc/Hz FoMT in 65nm CMOS
This work presents a millimeter-wave (mm-wave) dual-core quad-mode oscillator incorporating a switch-less tertiary loop to extend the frequency tuning range (FTR) without introducing additional switch loss or parasitic. The design couples two identical transformer-based dual-band (low- and high-frequency) voltage-controlled oscillators (VCOs), which are configurable in either even or odd modes via mode switches. In the high- and low-frequency band, the switch-less tertiary loop functions as an open circuit in the even mode and a short circuit in the odd mode, enabling four distinct frequency modes. Fabricated in a 65-nm CMOS process, the proposed oscillator achieves an FTR from 16.6 to 34.1 GHz, with phase noise ranging from −122.4 to −130.0 dBc/Hz at a 10-MHz offset, while consuming 9.5–11mW of power. This results in a peak FoM of 185.5 dBc/Hz and FoMT of 202.3 dBc/Hz.
- 4 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (5) , 593-596
A 28-/39-GHz CMOS LO Generator With Implicit Second and Third Harmonic Extraction Techniques for Multiband 5G mm-Wave Applications
This work presents a low-phase-noise millimeter-wave (mm-wave) local oscillator (LO) generator employing implicit second and third harmonic extraction techniques. The proposed harmonic extraction approach effectively improves phase noise performance in the mm-wave frequency range while maintaining the wide tuning range. Fabricated in a 65-nm CMOS process, the proposed LO generator achieves a wide frequency tuning range from 22 to 29.1 and 33 to 43.6 GHz. It consumes 7.4 and 8.8 mW for the second and third harmonic outputs, respectively. The second harmonic output achieves a phase noise of -131.1 dBc/Hz at a 10-MHz offset from a carrier frequency of 25.1 GHz, corresponding to a peak figure of merit (FoM) of 190.4 dBc/Hz. For the third harmonic output at 33.6 GHz, the phase noise is -128.4 dBc/Hz at a 10-MHz offset, resulting in a peak FoM of 189.5 dBc/Hz.
- 4 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (5) , 593-596
A 28-/39-GHz CMOS LO Generator With Implicit Second and Third Harmonic Extraction Techniques for Multiband 5G mm-Wave Applications
This work presents a low-phase-noise millimeter-wave (mm-wave) local oscillator (LO) generator employing implicit second and third harmonic extraction techniques. The proposed harmonic extraction approach effectively improves phase noise performance in the mm-wave frequency range while maintaining the wide tuning range. Fabricated in a 65-nm CMOS process, the proposed LO generator achieves a wide frequency tuning range from 22 to 29.1 and 33 to 43.6 GHz. It consumes 7.4 and 8.8 mW for the second and third harmonic outputs, respectively. The second harmonic output achieves a phase noise of -131.1 dBc/Hz at a 10-MHz offset from a carrier frequency of 25.1 GHz, corresponding to a peak figure of merit (FoM) of 190.4 dBc/Hz. For the third harmonic output at 33.6 GHz, the phase noise is -128.4 dBc/Hz at a 10-MHz offset, resulting in a peak FoM of 189.5 dBc/Hz.