Sahil Bansal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sahil Bansal has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Sai Hung Cheung
Nanyang Technological University
6 shared publications - Jyotish Kumar Das
University of Sheffield
3 shared publications - Raj Purohit Kiran
Indian Institute of Technology Delhi
3 shared publications Ayan Das
2 shared publications- Mohd Aman Khalid
Thapar Institute of Engineering and Technology
2 shared publications - Shakir Rather
Indian Institute of Technology Delhi
2 shared publications
Latest Publications
- 1 February 2027
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Design and Construction Practice
- Vol. 32 (1) , 04026094
Database-Driven Modeling Error Assessment of Shear Design Methods for UHPC Flexural Members without Shear Reinforcement
In recent years, a significant amount of experimentation has been conducted to evaluate the shear behavior of ultra-high performance concrete (UHPC) flexural members. Several codal procedures, including Swiss society of engineers and architects (SIA) 2052:2016, French national standard (NF)-P18:2016, Korean ultra-high performance concrete (K-UHPC) 2014, China Association for Engineering Construction Standardization (CECS) 38:2004, e.construct prestressed concrete institute (eCPCI) 2021, and federal highway administration (FHWA) 2023, have also been devised to predict the shear capacity of UHPC flexural members. In this study, a qualified database of shear test results was extracted to estimate the statistics of the modeling error defined as the ratio of experimentally obtained shear capacity and shear capacity predicted using design procedures from different codal provisions available for UHPC. Initially, conversion factors for compressive strength among different geometries were established based on the available data to ensure the application of compressive strength of a specific specimen geometry for a particular design procedure. Subsequently, the test data were critically reviewed, and criteria were developed to achieve a reliable database. The refined database comprised 119 test specimens that exhibited shear-dominated failure. However, experimentally obtained tensile properties and shear crack inclination angles, essential for the evaluation of various shear design provisions, were available for only 85 tests. For each shear design method, the modeling error was quantified, and its statistical parameters—mean and coefficient of variation—were computed to assess accuracy and consistency. These results can be used to perform a reliability-based evaluation of structures designed according to the codal provisions, which can be a baseline for reliability-based calibration.
- 1 February 2027
- Published by American Society of Civil Engineers (ASCE) in Journal of Structural Design and Construction Practice
- Vol. 32 (1) , 04026094
Database-Driven Modeling Error Assessment of Shear Design Methods for UHPC Flexural Members without Shear Reinforcement
In recent years, a significant amount of experimentation has been conducted to evaluate the shear behavior of ultra-high performance concrete (UHPC) flexural members. Several codal procedures, including Swiss society of engineers and architects (SIA) 2052:2016, French national standard (NF)-P18:2016, Korean ultra-high performance concrete (K-UHPC) 2014, China Association for Engineering Construction Standardization (CECS) 38:2004, e.construct prestressed concrete institute (eCPCI) 2021, and federal highway administration (FHWA) 2023, have also been devised to predict the shear capacity of UHPC flexural members. In this study, a qualified database of shear test results was extracted to estimate the statistics of the modeling error defined as the ratio of experimentally obtained shear capacity and shear capacity predicted using design procedures from different codal provisions available for UHPC. Initially, conversion factors for compressive strength among different geometries were established based on the available data to ensure the application of compressive strength of a specific specimen geometry for a particular design procedure. Subsequently, the test data were critically reviewed, and criteria were developed to achieve a reliable database. The refined database comprised 119 test specimens that exhibited shear-dominated failure. However, experimentally obtained tensile properties and shear crack inclination angles, essential for the evaluation of various shear design provisions, were available for only 85 tests. For each shear design method, the modeling error was quantified, and its statistical parameters—mean and coefficient of variation—were computed to assess accuracy and consistency. These results can be used to perform a reliability-based evaluation of structures designed according to the codal provisions, which can be a baseline for reliability-based calibration.
- 4 August 2026
- Published by Springer Nature in Journal of Civil Structural Health Monitoring
- Vol. 16 (5) , 65
FE model bayesian updating with complex modal parameters for a lab-scale pedestrian bridge
- 4 August 2026
- Published by Springer Nature in Journal of Civil Structural Health Monitoring
- Vol. 16 (5) , 65
FE model bayesian updating with complex modal parameters for a lab-scale pedestrian bridge
- 1 April 2026
- Published by Springer Nature
- p. 75-86
Mix Design of Ultra-High Performance Concrete Using Particle Packing Optimization
- 1 April 2026
- Published by Springer Nature
- p. 75-86
Mix Design of Ultra-High Performance Concrete Using Particle Packing Optimization
- 5 July 2025
- Published by Springer Nature in Optimization and Engineering
- Vol. 27 (1) , 99-134
A two-stage simulation-based framework for reliability-based robust design optimization of systems
- 5 July 2025
- Published by Springer Nature in Optimization and Engineering
- Vol. 27 (1) , 99-134
A two-stage simulation-based framework for reliability-based robust design optimization of systems
- 1 May 2025
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 77 (9-10) , 525-540
Effect of silica fume type, mixing sequence, and curing regime on workability and compressive strength of UHPC
The impacts of silica fume (SF) type, mixing sequence, and mixing time on the workability and compressive strength of ultra-high-performance concrete (UHPC) were examined. The effects of demolding time and curing regimes on the compressive strength and microstructure of UHPC were also investigated. The results indicated that undensified SF was more effective than densified SF in enhancing the workability and strength of UHPC. The mixing sequence and mixing time also influenced concrete workability and strength development. From the results of this work, it was concluded that incorporating SF in slurry form at the beginning and adding high-range water reducer in a single dosage with mixing water is more beneficial for achieving a homogenous UHPC mix. The preferable concrete demolding time is after 24 h. Any delay in demolding time for concrete made with a very low water/binder ratio may cause a reduction in strength development owing to insufficient hydration and the formation of shrinkage cracking. Water curing at 60°C was found to be more favorable for compressive strength development than water curing at 28°C and jute bag curing for up to 56 days. After 56 days, there was no significant variation in compressive strength of all the specimens subjected to different curing regimes.
- 1 May 2025
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 77 (9-10) , 525-540
Effect of silica fume type, mixing sequence, and curing regime on workability and compressive strength of UHPC
The impacts of silica fume (SF) type, mixing sequence, and mixing time on the workability and compressive strength of ultra-high-performance concrete (UHPC) were examined. The effects of demolding time and curing regimes on the compressive strength and microstructure of UHPC were also investigated. The results indicated that undensified SF was more effective than densified SF in enhancing the workability and strength of UHPC. The mixing sequence and mixing time also influenced concrete workability and strength development. From the results of this work, it was concluded that incorporating SF in slurry form at the beginning and adding high-range water reducer in a single dosage with mixing water is more beneficial for achieving a homogenous UHPC mix. The preferable concrete demolding time is after 24 h. Any delay in demolding time for concrete made with a very low water/binder ratio may cause a reduction in strength development owing to insufficient hydration and the formation of shrinkage cracking. Water curing at 60°C was found to be more favorable for compressive strength development than water curing at 28°C and jute bag curing for up to 56 days. After 56 days, there was no significant variation in compressive strength of all the specimens subjected to different curing regimes.
- Top Cited Papers
- 19 April 2025
- Published by Elsevier in Probabilistic Engineering Mechanics
- Vol. 80
A state-of-the-art review of Bayesian finite element model updating techniques for structural systems
- 19 April 2025
- Published by Elsevier in Probabilistic Engineering Mechanics
- Vol. 80
Top Cited PapersA state-of-the-art review of Bayesian finite element model updating techniques for structural systems
- 6 March 2025
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 608
Bayesian modal identification of non-classically damped systems using frequency domain data
- 6 March 2025
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 608
Bayesian modal identification of non-classically damped systems using frequency domain data
- 31 December 2024
- Published by Elsevier in Structures
- Vol. 71
Reliability-based design optimization of systems in Voronoi tessellation-based partitioned design space
- 31 December 2024
- Published by Elsevier in Structures
- Vol. 71
Reliability-based design optimization of systems in Voronoi tessellation-based partitioned design space
- 27 November 2024
- Published by Springer Nature
- p. 195-206
Finite Element Model Updating Using Modal Data
- 27 November 2024
- Published by Springer Nature
- p. 195-206
Finite Element Model Updating Using Modal Data