Shaoqin Ruan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shaoqin Ruan has a total of 120 co-authors. Here are the top co-authors by number of shared publications:
- Cise Unluer
Department of Civil Engineering and Management, University of Manchester, Manchester, UK
13 shared publications - Yufeng Song
College of Civil Engineering and Architecture Zhejiang University Hangzhou China
10 shared publications Xiaoqian Qian
7 shared publicationsZhiguang Wang
7 shared publications- Xiangming Zhou
Department of Civil and Environmental Engineering, Brunel University of London, London UB8 3PH, UK
6 shared publications Dongming Yan
College of Civil Engineering and Architecture Zhejiang University Hangzhou China
5 shared publications
Latest Publications
- Open Access
- 12 May 2026
- Published by Elsevier in SSRN Electronic Journal
Synergistic Interfacial Bonding and Pore Refinement in Cement-Based Materials via In-Situ Acrylamide Polymerization
Conventional polymer modification of cementitious materials to enhance flexural strength often yields marginal improvements and compromises compressive strength, primarily due to the poor dispersion and compatibility of high-viscosity polymers. To overcome these limitations, this study introduces an innovative strategy based on the in-situ polymerization of acrylamide (AM) monomer at ambient temperature. This work systematically optimizes the premixing time, a critical parameter governing the balance between uniform monomer dispersion and polymerization kinetics. Response Surface Methodology (RSM) was employed to identify the optimal synthesis conditions: an initiator/monomer mass ratio of 2.49%, an accelerator/monomer ratio of 3.02%, and a premixing time of 7 minutes. At a fixed AM content of 3 wt.%, the optimized formulation produced a cement paste exhibiting a 28-day flexural strength of 12.2 MPa—a 61% increase over the control paste—while maintaining comparable compressive strength. Microstructural analysis revealed that the in-situ-formed polyacrylamide (PAM) network refines the pore architecture by increasing the proportion of harmless pores (<20 nm), despite a slight increase in total porosity. Concurrently, chemical interactions between hydrolyzed carboxyl groups from PAM and metal ions within the hydration products strengthen the organic-inorganic interface. This synergy between pore refinement and enhanced interfacial bonding constitutes the fundamental mechanism underpinning the superior flexural performance.
- 12 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSynergistic Interfacial Bonding and Pore Refinement in Cement-Based Materials via In-Situ Acrylamide Polymerization
Conventional polymer modification of cementitious materials to enhance flexural strength often yields marginal improvements and compromises compressive strength, primarily due to the poor dispersion and compatibility of high-viscosity polymers. To overcome these limitations, this study introduces an innovative strategy based on the in-situ polymerization of acrylamide (AM) monomer at ambient temperature. This work systematically optimizes the premixing time, a critical parameter governing the balance between uniform monomer dispersion and polymerization kinetics. Response Surface Methodology (RSM) was employed to identify the optimal synthesis conditions: an initiator/monomer mass ratio of 2.49%, an accelerator/monomer ratio of 3.02%, and a premixing time of 7 minutes. At a fixed AM content of 3 wt.%, the optimized formulation produced a cement paste exhibiting a 28-day flexural strength of 12.2 MPa—a 61% increase over the control paste—while maintaining comparable compressive strength. Microstructural analysis revealed that the in-situ-formed polyacrylamide (PAM) network refines the pore architecture by increasing the proportion of harmless pores (<20 nm), despite a slight increase in total porosity. Concurrently, chemical interactions between hydrolyzed carboxyl groups from PAM and metal ions within the hydration products strengthen the organic-inorganic interface. This synergy between pore refinement and enhanced interfacial bonding constitutes the fundamental mechanism underpinning the superior flexural performance.
- Open Access
- 12 March 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16  (1)
Unlocking the reactivity of municipal solid waste incineration bottom ash through physicochemical co-activation toward improved cementitious performance
Neither mechanical refinement nor chemical activation alone typically provides sufficient reactivity enhancement or performance robustness for municipal solid waste incineration bottom ash (MSWIBA) when used as a supplementary cementitious material (SCM). This study proposes a physicochemical co-activation route combining planetary ball milling with Ca(OH)2 impregnation, and elucidates how the coupled treatment regulates hydration kinetics, strength development, and microstructural evolution in MSWIBA-blended binders. The results show that ball milling followed by immersion in a moderately concentrated Ca(OH)2 solution (~ 0.2 mol/L) establishes a dual activation pathway: particle disintegration and defect formation increase the accessible reactive surface, while alkaline–calcium conditioning promotes depolymerization of the aluminosilicate glass and exposes latent reactive sites. Consequently, early hydration is accelerated and sustained formation of C–S–H and AFt is promoted, yielding a compact and largely defect-free matrix. At 28 d, the optimized synergistically activated system achieves a compressive strength of 55.4 MPa, surpassing that of the ball-milled-only counterpart. Overall, the findings demonstrate a scalable physicochemical strategy for converting MSWIBA into a high-performance SCM.
- 12 March 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16  (1)
Open AccessUnlocking the reactivity of municipal solid waste incineration bottom ash through physicochemical co-activation toward improved cementitious performance
Neither mechanical refinement nor chemical activation alone typically provides sufficient reactivity enhancement or performance robustness for municipal solid waste incineration bottom ash (MSWIBA) when used as a supplementary cementitious material (SCM). This study proposes a physicochemical co-activation route combining planetary ball milling with Ca(OH)2 impregnation, and elucidates how the coupled treatment regulates hydration kinetics, strength development, and microstructural evolution in MSWIBA-blended binders. The results show that ball milling followed by immersion in a moderately concentrated Ca(OH)2 solution (~ 0.2 mol/L) establishes a dual activation pathway: particle disintegration and defect formation increase the accessible reactive surface, while alkaline–calcium conditioning promotes depolymerization of the aluminosilicate glass and exposes latent reactive sites. Consequently, early hydration is accelerated and sustained formation of C–S–H and AFt is promoted, yielding a compact and largely defect-free matrix. At 28 d, the optimized synergistically activated system achieves a compressive strength of 55.4 MPa, surpassing that of the ball-milled-only counterpart. Overall, the findings demonstrate a scalable physicochemical strategy for converting MSWIBA into a high-performance SCM.
- 21 August 2025
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 27  (38) , 11835-11856
Technical and carbon footprint assessment of mortars derived from CO2 and magnesia recovered from bischofite
Valorizing waste bischofite into reactive magnesia cement for CO2-sequestering mortars.
- 21 August 2025
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 27  (38) , 11835-11856
Technical and carbon footprint assessment of mortars derived from CO2 and magnesia recovered from bischofite
Valorizing waste bischofite into reactive magnesia cement for CO2-sequestering mortars.
- Open Access
- 17 July 2025
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 23
Performance of cement paste in direct aqueous carbonation with high CO2 flux enhanced by fly ash and sodium carboxylate
- 17 July 2025
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 23
Open AccessPerformance of cement paste in direct aqueous carbonation with high CO2 flux enhanced by fly ash and sodium carboxylate
- Open Access
- 14 February 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15  (1) , 1-21
Hydration behaviors, workability, and strength variations in direct aqueous carbonation (DAC) of Portland cement paste
This study investigates the mechanisms behind direct aqueous carbonation in concrete manufacturing, focusing on its effects on workability and strength. Through an analysis of cement paste under varying water-to-cement ratios (0.5, 0.55, and 0.6) and CO2 additive amount (0%, 0.1%, and 1%), the results demonstrate that early carbonation accelerates the setting process. Higher CO2 additive amounts and lower w/c ratios further reduce setting time and fluidity, also increase free water consumption, which negatively affects the pore structure and compressive strength. However, as the transformation of amorphous calcium carbonate to calcite, enhancing hydration during curing and ultimately improving the final compressive strength. This study elucidates the various effects of CO2 addition to cement paste on fresh and hardened paste during the direct aqueous carbonation process, shedding light on how it influences hydration, workability, and strength, contributing to sustainable concrete production.
- 14 February 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15  (1) , 1-21
Open AccessHydration behaviors, workability, and strength variations in direct aqueous carbonation (DAC) of Portland cement paste
This study investigates the mechanisms behind direct aqueous carbonation in concrete manufacturing, focusing on its effects on workability and strength. Through an analysis of cement paste under varying water-to-cement ratios (0.5, 0.55, and 0.6) and CO2 additive amount (0%, 0.1%, and 1%), the results demonstrate that early carbonation accelerates the setting process. Higher CO2 additive amounts and lower w/c ratios further reduce setting time and fluidity, also increase free water consumption, which negatively affects the pore structure and compressive strength. However, as the transformation of amorphous calcium carbonate to calcite, enhancing hydration during curing and ultimately improving the final compressive strength. This study elucidates the various effects of CO2 addition to cement paste on fresh and hardened paste during the direct aqueous carbonation process, shedding light on how it influences hydration, workability, and strength, contributing to sustainable concrete production.
- 3 December 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 98
Influences of cementitious capillary crystalline waterproofing on the hydration products and properties of cement-based materials
- 3 December 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 98
Influences of cementitious capillary crystalline waterproofing on the hydration products and properties of cement-based materials
- 21 June 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 94
Nano-modified recycled aggregates via vacuum impregnation: Towards stronger and durable recycled concrete
- 21 June 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 94
Nano-modified recycled aggregates via vacuum impregnation: Towards stronger and durable recycled concrete
- 16 April 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 89
Assessing the influence of external curing on the early drying shrinkage of ultra-high-performance concrete
- 16 April 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 89
Assessing the influence of external curing on the early drying shrinkage of ultra-high-performance concrete