Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Norbert Willenbacher has a total of 130 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Supramolecularly Anchored Skeleton‐Intrinsic Phase‐Change Monoliths Enabling Passive Thermal Homeostasis of Outdoor Electronics

    by Dongmei Lei, Yufeng Wang, Tianyi Zhu, Mengmeng Yuan, Mengyuan Jiang, Yujie Wei, Yue‐E. Miao, Norbert Willenbacher, Chao Zhang, Tianxi Liu

    Mitigating extreme temperature fluctuations is critical for maintaining data integrity and preventing failure in outdoor electronics. However, durable passive thermal homeostasis for such electronics under fluctuating outdoor conditions remains challenging. Here, we report a skeleton‐intrinsic phase‐change monolith (SPCM) fabricated through supramolecular anchoring. A noncovalent supramolecular network robustly confines molten phase‐change domains within a load‐bearing skeleton, combining a high latent‐heat capacity of 125 J g −1 with an ultralow thermal conductivity of 0.027 W m −1 K −1 . The monolith retains 99% of its mass after 100 thermal cycles and remains leak‐free under 50% compressive strain. By integrating thermal insulation, latent‐heat buffering, and radiative heat dissipation, SPCM protects electronic devices against external thermal shocks. An SPCM‐packaged electronic device exhibits a temperature variation of less than 1.5°C when exposed to a 120°C heat source, compared with approximately 25°C for an unprotected device. The monolith also largely retains its phase‐change behavior, thermal insulation performance, and spectral selectivity after thermal cycling and environmental exposure, demonstrating stability under the tested harsh conditions. This work establishes a supramolecular skeleton‐engineering strategy for passive thermal management of electronics in fluctuating outdoor environments.

  • Open Access

    The Capillary Suspension Concept Is Used to Obtain Polymer-Free Particle Contacts Enhancing Conductivity of Highly Filled Polymer Composites

    by Katrin Dyhr, Karim Abdel Aal, Anna-Maria Steck, Norbert Willenbacher

    Usually, particle morphology and surface treatment are adjusted to achieve high conductivity in highly filled conductive polymer composites. Here, we demonstrate that this key property can be further improved by keeping the particle contact regions free of polymer using an extension of the capillary suspension concept. If the secondary liquid is chosen such that it remains in the contact areas between conductive particles during solidification of the polymer phase, then the composite conductivity substantially increases. For both a thermoset and a thermoplastic model system including 40 vol.% silver particles in the paste, the conductivity was more than doubled compared to the respective binary system, reaching conductivity values up to (4.3 ± 0.2) × 106 Sm−1. SEM images clearly show the polymer-free contact regions in samples with enhanced conductivity. However, conductivity only increases if the secondary fluid is removed after solidification of the polymer phase. Thus, the capillary suspension concept can be used for a controlled modification of particle–particle contacts and represents a generic, viable strategy for enhancing conductivity in highly filled polymer composites. The concept helps to save precious (silver) resources and may find application in various fields of printed electronics, e.g., metallization of thermosensitive solar cells.

  • Polyethylene glycol-assisted stabilization of low-silver electrically conductive adhesives for solar cell interconnection

    by Marianne Kronsbein, Norbert Willenbacher

    Electrically conductive adhesives (ECAs) represent a low-temperature alternative to solder in electronic and photovoltaic applications. Their electrical performance relies on a conductive filler content typically ranging from 20-30 vol% silver flakes, which ensures percolation and high conductivity but raises cost and sustainability concerns. Here, we demonstrate that an ECA comprising an epoxy resin, a non-miscible polar fluid and silver flakes used in commercial products meets the specifications for shingled solar cell interconnection in terms of volume and contact resistivity as well as mechanical strength at a silver content of only 4 vol%. Such a low-filled ECA, however, suffers from poor stability against de-mixing and its flow properties are not suitable for screen printing or dispensing. This can be remedied by adding a small amount of polyethylene glycol (PEG) 200. PEG 200 partially dissolves in the epoxy resin but also in the polar fluid, thereby reducing the three-phase contact angle of the polar fluid on the silver flake surface. This appears to enable the formation of a “capillary” state capillary suspension with 2-3 vol% added PEG, which provides a high yield stress guaranteeing high stability and good application behavior. The corresponding coarsening of the microstructure does not affect the electrical properties. The application of this concept enables the formulation of an ECA that meets industrial performance criteria even at very low particle content. The transfer to other filler systems, such as silver-coated copper or glass particles, is straightforward and offers a pathway toward robust, cost-effective, and sustainable ECAs for next-generation photovoltaic modules.


  • Iodine-Induced Microphase Separation Controls the Flow Behavior and Electrical Conductivity of Silver-Filled Polymer Composites

    by Jonas Marten, Jennifer S. Urallar, Thao M. Duong, Patrick Théato, Norbert Willenbacher

    Silver-filled electrically conductive polymer composites play a crucial role in various fields of electronics, such as die attach, chip packaging, solar cell interconnection, and soft printed electronics. This study explores the use of iodine-induced microphase separation of silver particles to achieve high electrical conductivity in the corresponding polymer composites at low particle loading, thereby preserving this precious resource. Three iodine salts─1-butyl-3-methylimidazolium iodide, potassium iodide, and sodium iodide─were directly mixed into thermoplastic polyurethane solutions with varying contents of micron-sized silver particles. This resulted in a paste-like suspension texture, indicating the formation of a percolating particle network already in the wet state. The electrical conductivity of the corresponding dry films improved from 10-5 S/cm without added iodine to 500 or 2600 S/cm at 12 or 20 vol % silver, respectively, irrespective of the iodine type. Thermogravimetric analysis and infrared spectroscopy confirmed that iodine removes lubricants from the silver particle surfaces, facilitating stronger particle attraction. Accordingly, scanning electron microscopy revealed iodine-induced microstructural heterogeneities. These findings highlight the potential of iodine-modified, silver-filled polymer solutions as a straightforward, cost-efficient approach to producing high-performance conductive materials for electronic applications.


  • Top Cited Papers

    Thermal-Rectified Gradient Porous Nanocomposite Film Enabling Multiscenario Adaptive Radiative Cooling

    by Yufeng Wang, Song Liu, Xiaobo Zhang, Ying Liu, Tianyi Zhu, Baiyu Ji, Jianglong Chen, Yuanbo Cheng, Wei Fan, Yue-E Miao, et al.

    Micronanoporous structures hold high potential as radiative sky-cooling materials for zero-energy thermal regulation in enclosed spaces subjected to high temperatures and direct sunlight, owing to their combination of thermal insulation and sunlight scattering features. However, their constrained ability to reflect sunlight across the entire solar spectrum, coupled with the inefficient dissipation of excess internal heat, restricts their applicability in diverse cooling scenarios. Herein, we present a gradient cross-linked polymerization strategy for preparing a gradient porous nanocomposite film. This film features a dual-gradient distribution of nanoparticle content and pore size, achieving a solar reflectance of 96.2% and demonstrating thermal rectification properties with a thermal rectification factor of 30%. Functioning effectively as a thermally rectified radiative cooling panel, this gradient film delivers energy-efficient and adaptive cooling for multiple enclosed environments, regardless of whether indoor temperatures exceed or fall below ambient outdoor temperatures. This gradient film achieves an extra cooling effect of 2.4 and 2.2 °C for unheated and self-heated enclosed environments, respectively, compared to the cooling effect using conventional porous nanocomposite films. The gradient structural design for porous structural radiative cooling materials demonstrates multiscenario adaptive radiative cooling applications.


  • Open Access

    Mechanically Tunable DNA Hydrogels as Prospective Biosensing Modules

    by Asya E. Can, Abdul W. U. Ali, Claude Oelschlaeger, Norbert Willenbacher, Iliya D. Stoev

    Sequence‐programmable DNA building blocks offer high degree of freedom in designing arbitrarily complex networks of tunable viscoelastic properties. Yet, the deployment of DNA‐based functional materials remains limited due to insufficient control over the emerging structures and their mechanics. In an ongoing effort to place structure‐property relations in stimuli‐responsive DNA materials on a firm foundation, here a systematic rheological study of self‐assembling DNA networks is presented, comprised of short DNA nanomotifs, namely trivalent nanostars and bivalent linkers, where the latter differ in their composition on a single base‐pair level. Notably, we found through combining conventional bulk rheology with diffusing wave spectroscopy (DWS‐based) passive microrheology a relationship between the melting temperature of a DNA hydrogel and its DNA sequence composition. By providing a use case, we demonstrated how the determination of such empirical relations could impact the areas of biosensing and mechanical computing, where control over the system state and target identification are key.


  • Open Access

    Formulating Graphite-Filled PU Dispersions with Extended Shelf Life Using the Capillary Suspension Concept

    by Katrin Dyhr, Norbert Willenbacher

    Stabilizing micron-sized particles in low-viscosity polymer dispersions is challenging when density differences are present. This study demonstrates that graphite particles in aqueous polyurethane dispersions can be efficiently prevented from sedimentation using the capillary suspension concept. Capillary suspensions are solid/liquid/liquid systems and the capillary forces inferred from adding a second immiscible fluid can lead to drastic changes in texture and flow. Here, both spherical and flake-shaped graphite particles were used as fillers, with octanol as the secondary liquid. At low graphite concentrations, octanol increases the low-shear viscosity significantly attributed to the formation of loose particle aggregates immobilizing part of the continuous phase. Above a critical graphite concentration, capillary forces induce a self-assembling, percolating particle network, leading to a sharp yield stress increase (>100 Pa). The corresponding percolating particle network efficiently suppresses sedimentation; for the system including 28 vol% spherical particles, a shelf life of at least six months was achieved. Capillary forces do not affect the high-shear viscosity of suspensions; here, a hydrophobically modified polyether thickener can be used. Transfer of the stabilization concept presented here to other high-density particles like silver or metal oxides suspended in other polymer dispersions is straightforward and is applicable in various fields like flexible printed electronics.


  • Open Access

    How carboxymethylcellulose adsorption and porous active material particles diminish the adhesion of graphite-silicon anodes in lithium-ion batteries

    by Katarzyna Hofmann, Norbert Willenbacher

    Due to its adsorption on graphite and superior thickening properties, carboxymethylcellulose (CMC) is widely used as a dispersant and rheology modifier in water-based anode slurries for lithium-ion batteries. CMC also provides cohesion to the dry anode layer but exhibits poor adhesion to the copper foil necessitating the addition of styrene-butadiene rubber (SBR) as an adhesion promoter. High adhesion between the electrode layer and the current collector is crucial in electrode fabrication, especially for electrodes with higher mass loadings. In this work, we investigate how a polymeric binder, originally intended as a thickening and dispersing agent, can significantly affect the adhesive strength between the anode layer and the current collector. Our results reveal that CMC, by adsorbing onto active material particles (graphite, micro-silicon or nano-silicon), indirectly influences the anode adhesion. The adsorbed CMC layer hinders the direct binding of SBR to the active material particles, thereby creating the weakest link between the active layer and the current collector. This effect is more pronounced the higher the CMC molecular weight. Moreover, we could show that graphite-nano-silicon composite anodes exhibit a significantly reduced adhesion to the copper foil despite a low adsorption of CMC on nano-silicon, since a large fraction of SBR particles are trapped in the porous, micron-sized nano-silicon aggregates. Our findings highlight the importance of considering thickener adsorption on active material particles within electrode design, as a factor that exerts an indirect, albeit significant, influence on anode adhesion.


  • Open Access

    Processing of Aqueous Graphite–Silicon Oxide Slurries and Its Impact on Rheology, Coating Behavior, Microstructure, and Cell Performance

    by Peter Haberzettl, Nicholas Filipovic, Dragoljub Vrankovic, Norbert Willenbacher

    The mixing process is the basis of the electrode microstructure, which defines key cell performance indicators. This work investigated the effects of varying the energy input within the mixing procedure on slurry rheology, coating behavior, mechanical and electrical properties of dry electrodes and electrochemical performance of cells fabricated from these negative electrodes. Energy input differences were achieved by varying the solids content within the mixing procedure; however, the final total solids content of the slurries was always the same. The slurries, produced with graphite and silicon oxide as active materials and carboxymethylcellulose (CMC) and styrene-butadiene rubber as binders, showed large differences in flow behavior which were explained by changes in CMC adsorption and mechanical degradation because of increasing energy input. Low shear viscosity and the degree of shear thinning decreased with increasing energy input, resulting in a narrower stability window for slot-die coating. The resistance between the electrode and current collector decreased as more CMC was adsorbed on the active material. Electrode adhesion drastically dropped at the highest energy input, presumably due to a change in SBR distribution. Despite these variations, all fabricated pouch cells demonstrated excellent electrochemical performance and a slight trend of increased charge capability was observed in cells prepared with higher energy input.