M. J. Daniel Esser
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
M. J. Daniel Esser has a total of 102 co-authors. Here are the top co-authors by number of shared publications:
C. Bollig
National Laser Centre, CSIR, PO Box 395, Pretoria, 0001 South Africa
12 shared publications- Richard M. Carter
Institute of Photonics and Quantum Sciences, Heriot-Watt University, Edinburgh, EH14 4AS, UK
12 shared publications Duncan P. Hand
9 shared publicationsAdrian Dzipalski
6 shared publicationsC. Jacobs
National Laser Centre, Council for Scientific and Industrial Research, P.O. Box 395, Pretoria 0001, South Africa
6 shared publicationsIan Elder
Leonardo MW Ltd
6 shared publications
Latest Publications
- Open Access
- 20 July 2026
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 16 (8) , 2570
2 µm wavelength nanosecond laser welding of silicon
We investigate direct laser welding of silicon-to-silicon, without the requirement of any interlayers, using 40 ns pulses at 2.1 µm wavelength and 1 kHz repetition rate. A parameter study was conducted over pulse energies from 20–50.2 µJ, scan speeds from 1 mm/s – 0.015 mm/s for various depths of focus. Successful bonding was achieved through individual melt features within the weld track, analyzed with a bespoke IR transmission microscope, with slower scan speeds and higher pulse energies increasing the number of these features. For 1090 µm thick silicon samples, the optimum focal plane for a 50 µJ pulse energy was found to be approximately 200 µm below the interface. Scanning electron microscope analysis confirms material redistribution between the top and bottom samples, thus providing evidence of silicon-to-silicon laser welding.
- 20 July 2026
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 16 (8) , 2570
Open Access2 µm wavelength nanosecond laser welding of silicon
We investigate direct laser welding of silicon-to-silicon, without the requirement of any interlayers, using 40 ns pulses at 2.1 µm wavelength and 1 kHz repetition rate. A parameter study was conducted over pulse energies from 20–50.2 µJ, scan speeds from 1 mm/s – 0.015 mm/s for various depths of focus. Successful bonding was achieved through individual melt features within the weld track, analyzed with a bespoke IR transmission microscope, with slower scan speeds and higher pulse energies increasing the number of these features. For 1090 µm thick silicon samples, the optimum focal plane for a 50 µJ pulse energy was found to be approximately 200 µm below the interface. Scanning electron microscope analysis confirms material redistribution between the top and bottom samples, thus providing evidence of silicon-to-silicon laser welding.
- Open Access
- 8 July 2026
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 16 (8) , 2376
Effect of linear laser polarization angle on internal ultrashort-pulsed laser processing of bulk quartz crystal
The effect of varying the relative angles between the linear polarization state of a laser beam, write-direction, and the optic-axis (C-axis) when ultrashort-pulsed laser processing crystalline quartz is investigated. Various 1030 nm pulse energies were used at 420 fs, 5 MHz with 2 mm/s write-speed. Strongly varying, and closely correlated, pulse energy thresholds for modification and damage are identified for angles of 0° to 90° between the C-axis and incident polarization. The maximum modification threshold was observed with the polarization oriented at 60° to the C-axis. The pulse energy threshold is minimized to 33% of the maximum at 0° angle, when the laser polarization, crystal C-axis and write-direction are parallel.
- 8 July 2026
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 16 (8) , 2376
Open AccessEffect of linear laser polarization angle on internal ultrashort-pulsed laser processing of bulk quartz crystal
The effect of varying the relative angles between the linear polarization state of a laser beam, write-direction, and the optic-axis (C-axis) when ultrashort-pulsed laser processing crystalline quartz is investigated. Various 1030 nm pulse energies were used at 420 fs, 5 MHz with 2 mm/s write-speed. Strongly varying, and closely correlated, pulse energy thresholds for modification and damage are identified for angles of 0° to 90° between the C-axis and incident polarization. The maximum modification threshold was observed with the polarization oriented at 60° to the C-axis. The pulse energy threshold is minimized to 33% of the maximum at 0° angle, when the laser polarization, crystal C-axis and write-direction are parallel.
- Open Access
- 30 June 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (14) , 25406
Ultrashort pulsed laser welding of crystalline quartz to metals with differing thermo-mechanical properties
We report ultrashort pulse (USP) laser welding of crystalline quartz to four industrial materials: titanium, stainless steel, aluminum, and copper, exhibiting coefficients of thermal expansion (CTE) mismatch from 1.5 to 15.9 μmm −1 K −1 . Welding was conducted using 5 ps, 1030 nm pulses with a high NA focus. Performance was evaluated using stress-induced birefringence, thermal cycling, and shear strength. All samples showed acceptable results with birefringent phase retardation (<5 nm/cm) and breaking strengths varying between 147 ± 60 N for copper and 110 ± 70 N for titanium. Performance variations are attributed to differences in thermo-mechanical properties, with the unexpected observation that it is not dominated by the CTE mismatch.
- 30 June 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (14) , 25406
Open AccessUltrashort pulsed laser welding of crystalline quartz to metals with differing thermo-mechanical properties
We report ultrashort pulse (USP) laser welding of crystalline quartz to four industrial materials: titanium, stainless steel, aluminum, and copper, exhibiting coefficients of thermal expansion (CTE) mismatch from 1.5 to 15.9 μmm −1 K −1 . Welding was conducted using 5 ps, 1030 nm pulses with a high NA focus. Performance was evaluated using stress-induced birefringence, thermal cycling, and shear strength. All samples showed acceptable results with birefringent phase retardation (<5 nm/cm) and breaking strengths varying between 147 ± 60 N for copper and 110 ± 70 N for titanium. Performance variations are attributed to differences in thermo-mechanical properties, with the unexpected observation that it is not dominated by the CTE mismatch.
- Open Access
- 8 June 2026
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 16 (7) , 1995
Ultrashort pulse laser welding of silicon carbide (4H-SiC) to glasses and crystals
We report the successful application of ultra-short pulse (USP) laser welding using a low numerical aperture (NA ∼0.02) beam delivery system coupled into a scanning galvanometer to bond 4H-silicon carbide (4H-SiC) to BK7, fused silica, and crystalline quartz. 4H-SiC is known for its exceptional thermomechanical properties, making it an ideal candidate for demanding high-temperature and pressure applications. This study is evaluating the impacts of CTE mismatch between the dissimilar material combinations on the weldability and survivability of the assemblies. Additionally, we evaluated the thermal and humidity cycling survivability of the welded assemblies, demonstrating the robustness of the joints under environmental stress.
- 8 June 2026
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 16 (7) , 1995
Open AccessUltrashort pulse laser welding of silicon carbide (4H-SiC) to glasses and crystals
We report the successful application of ultra-short pulse (USP) laser welding using a low numerical aperture (NA ∼0.02) beam delivery system coupled into a scanning galvanometer to bond 4H-silicon carbide (4H-SiC) to BK7, fused silica, and crystalline quartz. 4H-SiC is known for its exceptional thermomechanical properties, making it an ideal candidate for demanding high-temperature and pressure applications. This study is evaluating the impacts of CTE mismatch between the dissimilar material combinations on the weldability and survivability of the assemblies. Additionally, we evaluated the thermal and humidity cycling survivability of the welded assemblies, demonstrating the robustness of the joints under environmental stress.
- Open Access
- 27 January 2026
- Published by Elsevier in Pattern Recognition
- Vol. 176
A two-stage learning framework with a beam image dataset for automatic laser resonator alignment
- 27 January 2026
- Published by Elsevier in Pattern Recognition
- Vol. 176
Open AccessA two-stage learning framework with a beam image dataset for automatic laser resonator alignment
- Open Access
- 28 April 2025
- Published by Springer Nature in Glass Structures & Engineering
- Vol. 10 (2) , 1-16
Ultra-short pulsed laser welded-and-cut glass support pillars for vacuum insulating glass
Vacuum insulating glass (VIG) has demonstrated competitive Ug-values (heat transfer coefficients) which show promise to further reduce energy consumption from buildings. Support pillars are an essential part of the design as they support the glass panes which would otherwise deform, and potentially collapse, under the pressure differential between the internal vacuum and the external atmosphere, however they act as small thermal bridges which contribute to heat transfer through the panes. The main cause for this is their high thermal conductivity as they are made out of metal. The use of glass support pillars would improve the Ug-value by 10–20% depending on the pillar size and pillar separation. Additionally, a directly bonded glass pillar, made from the same material as the glass panes, without the need for any adhesives, would improve recycling and visual appearance. We demonstrate a new technique for manufacturing glass support pillars using laser welding to bond, and laser cutting to shape the pillar to the substrate glass. We show that these pillars are able to withstand the expected atmospheric compressive force related to a pillar separation of 20 mm with promise for future research.
- 28 April 2025
- Published by Springer Nature in Glass Structures & Engineering
- Vol. 10 (2) , 1-16
Open AccessUltra-short pulsed laser welded-and-cut glass support pillars for vacuum insulating glass
Vacuum insulating glass (VIG) has demonstrated competitive Ug-values (heat transfer coefficients) which show promise to further reduce energy consumption from buildings. Support pillars are an essential part of the design as they support the glass panes which would otherwise deform, and potentially collapse, under the pressure differential between the internal vacuum and the external atmosphere, however they act as small thermal bridges which contribute to heat transfer through the panes. The main cause for this is their high thermal conductivity as they are made out of metal. The use of glass support pillars would improve the Ug-value by 10–20% depending on the pillar size and pillar separation. Additionally, a directly bonded glass pillar, made from the same material as the glass panes, without the need for any adhesives, would improve recycling and visual appearance. We demonstrate a new technique for manufacturing glass support pillars using laser welding to bond, and laser cutting to shape the pillar to the substrate glass. We show that these pillars are able to withstand the expected atmospheric compressive force related to a pillar separation of 20 mm with promise for future research.
- Open Access
- 14 October 2024
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 14 (11) , 2588-2599
Industrial picosecond pulse laser welding of stainless-steel to quartz for optical applications
We report on the development of a robust picosecond laser welding process for the industrially relevant material combination of quartz and stainless steel. The process requires high numerical aperture focusing of a 6 ps 1030 nm laser through the transparent quartz onto the interface between the two materials. It is found that increased mechanical pressure applied during welding increases reliability and weld performance and with the correct choice of welding parameters parts will survive ISO standard thermal cycling and vibration testing demonstrating the suitability of the process for industrial application.
- 14 October 2024
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 14 (11) , 2588-2599
Open AccessIndustrial picosecond pulse laser welding of stainless-steel to quartz for optical applications
We report on the development of a robust picosecond laser welding process for the industrially relevant material combination of quartz and stainless steel. The process requires high numerical aperture focusing of a 6 ps 1030 nm laser through the transparent quartz onto the interface between the two materials. It is found that increased mechanical pressure applied during welding increases reliability and weld performance and with the correct choice of welding parameters parts will survive ISO standard thermal cycling and vibration testing demonstrating the suitability of the process for industrial application.
- 1 January 2024
- Published by Optica Publishing Group
- p. JW2A.9
Ho:YAG Slab Amplifier for Ultra-short-pulse Laser Processing of Infrared Optical Materials
A bespoke ultra-short-pulse seed laser is amplified by an in-house developed Ho:YAG pre-amplifier and Ho:YAG thin-slab main amplifier to micro-Joule energies at 23 MHz, aimed at non-linear material processing of infrared optical materials.
- 1 January 2024
- Published by Optica Publishing Group
- p. JW2A.9
Ho:YAG Slab Amplifier for Ultra-short-pulse Laser Processing of Infrared Optical Materials
A bespoke ultra-short-pulse seed laser is amplified by an in-house developed Ho:YAG pre-amplifier and Ho:YAG thin-slab main amplifier to micro-Joule energies at 23 MHz, aimed at non-linear material processing of infrared optical materials.
- 1 January 2024
- Published by Optica Publishing Group
- p. AM3A.8
Highly Compact Stable-Unstable Tm:LLF Thin-Slab Resonator
A compact hybrid stable-unstable Tm:LLF thin-slab laser is demonstrated utilising toroidal mirrors, with estimated M2 of 1.6 and 3.3 in minor and major axes, and over 30 times greater brightness than an equivalent stable resonator.
- 1 January 2024
- Published by Optica Publishing Group
- p. AM3A.8
Highly Compact Stable-Unstable Tm:LLF Thin-Slab Resonator
A compact hybrid stable-unstable Tm:LLF thin-slab laser is demonstrated utilising toroidal mirrors, with estimated M2 of 1.6 and 3.3 in minor and major axes, and over 30 times greater brightness than an equivalent stable resonator.
- 1 January 2023
- Published by Optica Publishing Group
- p. AW3A.6
Optimising Efficiency in Thin-Slab Thulium Lasers
Methods for improving diode-end-pumped thin-slab laser efficiency are presented, involving optimised pump delivery, stress-free mounting with interface materials and ASE suppression. Using these, our Tm:YLF system achieves 55-60% slope efficiency, with potential scaling past 300W.
- 1 January 2023
- Published by Optica Publishing Group
- p. AW3A.6
Optimising Efficiency in Thin-Slab Thulium Lasers
Methods for improving diode-end-pumped thin-slab laser efficiency are presented, involving optimised pump delivery, stress-free mounting with interface materials and ASE suppression. Using these, our Tm:YLF system achieves 55-60% slope efficiency, with potential scaling past 300W.