Vladimir Ukhin
Vladimir Ukhin has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Anastasiia Yuriivna Semenko
Physico-Technological Institute of Metals and Alloys of the National Academy of Sciences of Ukraine, Kyiv, Ukraine
4 shared publications - Oleksiy Mykolaiovych Smirnov
Physico-Technological Institute of Metals and Alloys of the National Academy of Sciences of Ukraine, Kyiv, Ukraine
4 shared publications - A. N. Smirnov
Сколковский институт науки и технологий, Москва, Россия
3 shared publications - Aleksei Verzilov
Physico-Technological Institute of Metals and Alloys of National Academy of Sciences of Ukraine
3 shared publications - Sergii Semiriagin
Physico-technological Institute of Metals and Alloys of the NAS of Ukraine (Kyiv, Ukraine)
2 shared publications - Volodymyr Tunyk
Physico-Technological Institute of Metals and Alloys, The NAS of Ukraine (PTIMA of the NAS of Ukraine)
2 shared publications
Latest Publications
- Open Access
- 10 September 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 157 (3) , 9-18
A STUDY OF THE INFLUENCE OF TECHNOLOGICAL PARAMETERS ON THE FORMATION OF INTERNAL DEFECTS IN THE BILLET DURING WHEEL AND BELT CASTING PROCESS
To ensure the guaranteed quality of the billet (including internal volumes) in the process of bell and wheel, it is necessary to strictly adhere to a set of such inextricably linked technological parame- ters of casting as: the speed of the billet movement, the profile of the mold, the temperature liquid copper, which take into account the formation features of the solid shell under the conditions of a certain wheel. A mathematical model has been developed that allows to simulate the solidification of a copper billet cast on the wheel depending on its rotation speed, pouring temperature and cooling conditions, as well as to predict the quality of the internal structure of metal products. With the help of the created mathematical model, it was established that speed values of 1800-1900 rph and higher lead to the boundary of the solidification zone falling outside the permissible val- ues that determined by the condition of the separation of the billet from the wheel and its plastic deformation during the straightening process. Copper castings in the speed range of 1600-1800 rph are in the zone of increased risk of obtaining internal defects in the billet, which are caused by the conditions of difficult feeding of its internal areas with liquid metal. This is due to the fact that the billet begins to move up after reaching the lower critical point of the wheel. The most effective (from the point of view of productivity and quality of the billet) wheel rotating speed values are in the range of 1450-1600 rph. At the same time, it is advisable to control the profile of the working cavity of the wheel and determine the permissible deviations in its wear. Deviation from the nominal casting parameters can lead to uneven contact of the solidified shell with the wheel wall, which can cause defects in the geometric shape of the billet. Для забезпечення гарантованої якості заготовки (у тому числі внутрішніх обсягів) у процесі розливання міді на колесо необхідно суворо дотримуватися сукупності таких нерозривно пов’язаних між собою технологічних параметрів лиття, як швидкість руху заготовки, профіль кристалізатора, температура міді, що розливається, які враховують особливості формування твердої скоринки в умовах певного колеса. Розроблено математичну модель, що дозволяє імітувати затвердіння мідної заготовки, яка відливається на колесо, залежно від швидкості його обертання, температури розливання і умов охолодження, а також прогнозувати якість внутрішньої структури металопродукції. За допомогою створеної математичної моделі встановлено, що значення швидкості 1800–1900 об/год і вище призводять до потрапляння межі зони твердіння за границю допустимих значень, що визначаються умовою відділення заготовки від колеса та її пластичною деформацією у процесі розправлення. Розливання міді в діапазоні швидкостей 1600–1800 об/год перебува- ють у зоні підвищеного ризику отримання внутрішніх дефектів заготовки, спричинені умовами утрудненого живлення її внутрішніх областей рідким металом. Це зумовлено тим, що заготовка починає рухатися вгору після досягнення нижньої критичної точки колеса. Найефективнішими (з точки зору продуктивності та якості заготовки) значеннями швидкості обертання колеса є діапазон 1450–1600 об/год. При цьому доцільно здійснювати контроль профілю робочої порожнини колеса та визначити допустимі відхилення в його зношення. Відхилення від номінальних параметрів лиття може призвести до нерівномірного контакту скоринки, яка твердіє, зі стінкою колеса, що може стати причиною виникнення дефектів геометричної форми заготовки.
- 10 September 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 157 (3) , 9-18
Open AccessA STUDY OF THE INFLUENCE OF TECHNOLOGICAL PARAMETERS ON THE FORMATION OF INTERNAL DEFECTS IN THE BILLET DURING WHEEL AND BELT CASTING PROCESS
To ensure the guaranteed quality of the billet (including internal volumes) in the process of bell and wheel, it is necessary to strictly adhere to a set of such inextricably linked technological parame- ters of casting as: the speed of the billet movement, the profile of the mold, the temperature liquid copper, which take into account the formation features of the solid shell under the conditions of a certain wheel. A mathematical model has been developed that allows to simulate the solidification of a copper billet cast on the wheel depending on its rotation speed, pouring temperature and cooling conditions, as well as to predict the quality of the internal structure of metal products. With the help of the created mathematical model, it was established that speed values of 1800-1900 rph and higher lead to the boundary of the solidification zone falling outside the permissible val- ues that determined by the condition of the separation of the billet from the wheel and its plastic deformation during the straightening process. Copper castings in the speed range of 1600-1800 rph are in the zone of increased risk of obtaining internal defects in the billet, which are caused by the conditions of difficult feeding of its internal areas with liquid metal. This is due to the fact that the billet begins to move up after reaching the lower critical point of the wheel. The most effective (from the point of view of productivity and quality of the billet) wheel rotating speed values are in the range of 1450-1600 rph. At the same time, it is advisable to control the profile of the working cavity of the wheel and determine the permissible deviations in its wear. Deviation from the nominal casting parameters can lead to uneven contact of the solidified shell with the wheel wall, which can cause defects in the geometric shape of the billet. Для забезпечення гарантованої якості заготовки (у тому числі внутрішніх обсягів) у процесі розливання міді на колесо необхідно суворо дотримуватися сукупності таких нерозривно пов’язаних між собою технологічних параметрів лиття, як швидкість руху заготовки, профіль кристалізатора, температура міді, що розливається, які враховують особливості формування твердої скоринки в умовах певного колеса. Розроблено математичну модель, що дозволяє імітувати затвердіння мідної заготовки, яка відливається на колесо, залежно від швидкості його обертання, температури розливання і умов охолодження, а також прогнозувати якість внутрішньої структури металопродукції. За допомогою створеної математичної моделі встановлено, що значення швидкості 1800–1900 об/год і вище призводять до потрапляння межі зони твердіння за границю допустимих значень, що визначаються умовою відділення заготовки від колеса та її пластичною деформацією у процесі розправлення. Розливання міді в діапазоні швидкостей 1600–1800 об/год перебува- ють у зоні підвищеного ризику отримання внутрішніх дефектів заготовки, спричинені умовами утрудненого живлення її внутрішніх областей рідким металом. Це зумовлено тим, що заготовка починає рухатися вгору після досягнення нижньої критичної точки колеса. Найефективнішими (з точки зору продуктивності та якості заготовки) значеннями швидкості обертання колеса є діапазон 1450–1600 об/год. При цьому доцільно здійснювати контроль профілю робочої порожнини колеса та визначити допустимі відхилення в його зношення. Відхилення від номінальних параметрів лиття може призвести до нерівномірного контакту скоринки, яка твердіє, зі стінкою колеса, що може стати причиною виникнення дефектів геометричної форми заготовки.
- 15 June 2024
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 19 (3) , 1438-1447
Evaluation of the Possibilities for Improving Durability of Large Ingot Molds Made of Pig Iron Using Vibration Treatment of the Melt
- 15 June 2024
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 19 (3) , 1438-1447
Evaluation of the Possibilities for Improving Durability of Large Ingot Molds Made of Pig Iron Using Vibration Treatment of the Melt
- 1 January 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 32 (2)
The effect of phosphorus content in copper alloys used for crystallisers of continuous casting machines
One of the key elements defining the technical level and operational capabilities of continuous casting machines (CCM) is the complex of physico-mechanical properties of copper or copper alloys used in its production. The paper provides a comprehensive assessment of the possibility of obtaining high-quality copper plates for CCBC crystallizers based on domestic technologies and equipment using refined copper. Special attention was paid to the need to optimize the chemical composition of the copper alloy within a narrower range of chemical element values. The analysis of the research shows that currently used copper alloys for CCM crystallizer manufacturing have a wide range of fluctuations in the main operational properties, namely thermal conductivity (260-390 W/(m·K)) and solidification temperature (250-700 °C). However, most of the alloys used have narrower fluctuation limits for acceptable values, constituting 340-390 W/(m·K) for thermal conductivity and 300-370 °C for solidification temperature, significantly depending on the impurity content in the copper alloy. Generalizing graphical dependencies, it should be assumed that the rational phosphorus content in the alloy is in the range of 40-120 ppm. In this case, the thermal conductivity of the alloy will be in the range of 370-400 W/(m·K), the solidification temperature will be 410-440 °C, and the recrystallization start temperature will be 370-400 °C. Moreover, such a phosphorus content interval is technologically feasible to maintain during billet casting. It is also shown that normalization annealing after cold deformation in the temperature range of 320-350 °C is capable of increasing the thermal conductivity of the alloy by 1-2 %. As a result of the conducted research, optimal limits of phosphorus content in fire-refined copper were established, ensuring the level of its physico-mechanical properties not lower than the indicators characteristic of alloys obtained from cathode copper. However, besides phosphorus, other alloy impurities, the content of which differs from the values characteristic of alloys obtained from cathode copper, may affect the properties of the material made from refined copper. Therefore, further research will focus on studying their complex impact on the physico-mechanical properties of refined alloys.
- 1 January 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 32 (2)
The effect of phosphorus content in copper alloys used for crystallisers of continuous casting machines
One of the key elements defining the technical level and operational capabilities of continuous casting machines (CCM) is the complex of physico-mechanical properties of copper or copper alloys used in its production. The paper provides a comprehensive assessment of the possibility of obtaining high-quality copper plates for CCBC crystallizers based on domestic technologies and equipment using refined copper. Special attention was paid to the need to optimize the chemical composition of the copper alloy within a narrower range of chemical element values. The analysis of the research shows that currently used copper alloys for CCM crystallizer manufacturing have a wide range of fluctuations in the main operational properties, namely thermal conductivity (260-390 W/(m·K)) and solidification temperature (250-700 °C). However, most of the alloys used have narrower fluctuation limits for acceptable values, constituting 340-390 W/(m·K) for thermal conductivity and 300-370 °C for solidification temperature, significantly depending on the impurity content in the copper alloy. Generalizing graphical dependencies, it should be assumed that the rational phosphorus content in the alloy is in the range of 40-120 ppm. In this case, the thermal conductivity of the alloy will be in the range of 370-400 W/(m·K), the solidification temperature will be 410-440 °C, and the recrystallization start temperature will be 370-400 °C. Moreover, such a phosphorus content interval is technologically feasible to maintain during billet casting. It is also shown that normalization annealing after cold deformation in the temperature range of 320-350 °C is capable of increasing the thermal conductivity of the alloy by 1-2 %. As a result of the conducted research, optimal limits of phosphorus content in fire-refined copper were established, ensuring the level of its physico-mechanical properties not lower than the indicators characteristic of alloys obtained from cathode copper. However, besides phosphorus, other alloy impurities, the content of which differs from the values characteristic of alloys obtained from cathode copper, may affect the properties of the material made from refined copper. Therefore, further research will focus on studying their complex impact on the physico-mechanical properties of refined alloys.
- Open Access
- 1 January 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 31 (2)
Some specifics of the billet open and submerged stream casting
Проведено експериментальні серії розливання сталі для визначення впливу методу безперервного розливання на частоту формування дефектів сортової заготовки. При цьому виробництво квадратних заготовок перетином 125х125 мм здійснювалось на шестиструмковій сортовій машині безперервного лиття заготовок (МБЛЗ) зі швидкостями розливання 2,8-4,3 м/хв. У процесі дослідження спочатку була розлита серія з 5 плавок сталі 60 (Ст60) відкритим струменем. Після цього, з використанням тих же гільз кристалізаторів, послідовно розливали закритим струменем 5 плавок сталі 40Х. Шляхом промислового експерименту було визначено, що в результаті безперервного розливання сталі відкритим струменем кількість ромбічності сортової заготовки становить 4,5 %. Зокрема, у випадку застосування технології розливання металу закритим струменем дефектів геометричної форми заготовок не виявлено. Використання системи «стопор-моноблок» — «стакан-дозатор» — «занурений стакан» дозволяє більш точно й вчасно регулювати витрату металу під час розливання в автоматичному режимі, не змінюючи швидкість витягування заготовки. При цьому забезпечується збереження рівня металевого розплаву в кристалізаторі, що найбільш точно враховує особливості формування скоринки заготовки по всій довжині гільзи при поточній швидкості лиття. Відсутність необхідності регулювання швидкості розливання рівнем металу в промківші дозволяє підтримувати в ньому оптимальну кількість розплаву, що стабілізує температуру розливання. Підведення струменя сталі за допомогою зануреного стакана під рівень металу в кристалізаторі запобігає бурлінню на межі розподілу фаз, а можливість істотного збільшення внутрішнього діаметра стакана-дозатора (у порівнянні з вільним витіканням) у кілька разів знижує швидкість його заростання відкладеннями корунду. Крім цього, розливання закритим струменем дозволяє застосовувати спеціальні шлакоутворюючі суміші, які забезпечують покращення якості поверхні заготовки. Додатково підвищити якість безперервнолитих зливків можливо за рахунок застосування електромагнітного перемішування рідкої сталі.
- 1 January 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 31 (2)
Open AccessSome specifics of the billet open and submerged stream casting
Проведено експериментальні серії розливання сталі для визначення впливу методу безперервного розливання на частоту формування дефектів сортової заготовки. При цьому виробництво квадратних заготовок перетином 125х125 мм здійснювалось на шестиструмковій сортовій машині безперервного лиття заготовок (МБЛЗ) зі швидкостями розливання 2,8-4,3 м/хв. У процесі дослідження спочатку була розлита серія з 5 плавок сталі 60 (Ст60) відкритим струменем. Після цього, з використанням тих же гільз кристалізаторів, послідовно розливали закритим струменем 5 плавок сталі 40Х. Шляхом промислового експерименту було визначено, що в результаті безперервного розливання сталі відкритим струменем кількість ромбічності сортової заготовки становить 4,5 %. Зокрема, у випадку застосування технології розливання металу закритим струменем дефектів геометричної форми заготовок не виявлено. Використання системи «стопор-моноблок» — «стакан-дозатор» — «занурений стакан» дозволяє більш точно й вчасно регулювати витрату металу під час розливання в автоматичному режимі, не змінюючи швидкість витягування заготовки. При цьому забезпечується збереження рівня металевого розплаву в кристалізаторі, що найбільш точно враховує особливості формування скоринки заготовки по всій довжині гільзи при поточній швидкості лиття. Відсутність необхідності регулювання швидкості розливання рівнем металу в промківші дозволяє підтримувати в ньому оптимальну кількість розплаву, що стабілізує температуру розливання. Підведення струменя сталі за допомогою зануреного стакана під рівень металу в кристалізаторі запобігає бурлінню на межі розподілу фаз, а можливість істотного збільшення внутрішнього діаметра стакана-дозатора (у порівнянні з вільним витіканням) у кілька разів знижує швидкість його заростання відкладеннями корунду. Крім цього, розливання закритим струменем дозволяє застосовувати спеціальні шлакоутворюючі суміші, які забезпечують покращення якості поверхні заготовки. Додатково підвищити якість безперервнолитих зливків можливо за рахунок застосування електромагнітного перемішування рідкої сталі.
- Open Access
- 6 October 2020
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 28 (3) , 40-46
Study of the processes of subsurface crack formation in a rhombic varietal billet during production in the conditions of a metallurgical micro-mill
Study of the processes of subsurface crack formation in a rhombic varietal billet during production in the conditions of a metallurgical micro-mill
- 6 October 2020
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 28 (3) , 40-46
Open AccessStudy of the processes of subsurface crack formation in a rhombic varietal billet during production in the conditions of a metallurgical micro-mill
Study of the processes of subsurface crack formation in a rhombic varietal billet during production in the conditions of a metallurgical micro-mill
- Open Access
- 1 January 2020
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 28 (1)
Investigation of internal defects formation reasons in copper billet obtained at rotary continuous casting machine (CCM)
Investigation of internal defects formation reasons in copper billet obtained at rotary continuous casting machine (CCM)
- 1 January 2020
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 28 (1)
Open AccessInvestigation of internal defects formation reasons in copper billet obtained at rotary continuous casting machine (CCM)
Investigation of internal defects formation reasons in copper billet obtained at rotary continuous casting machine (CCM)
- Open Access
- 1 November 2019
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 312-313 (5-6) , 21-27
Investigation of billet crystal structure formation features during forced stirring of its liquid core
The most effective method for studying the dynamics of solidification of various kinds of ingots is physical modeling. A physical model that simulates a cross section of a continuously cast billet was created.
- 1 November 2019
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 312-313 (5-6) , 21-27
Open AccessInvestigation of billet crystal structure formation features during forced stirring of its liquid core
The most effective method for studying the dynamics of solidification of various kinds of ingots is physical modeling. A physical model that simulates a cross section of a continuously cast billet was created.
- 1 December 2007
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2007 (8) , 672-675
Effect of argon injection on the rim formation in a section continuous casting
The effect of argon blowing into a steel stream on the stability of continuous casting is studied. Physical modeling and mathematical simulation are performed to find the parameters of argon blowing...
- 1 December 2007
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2007 (8) , 672-675
Effect of argon injection on the rim formation in a section continuous casting
The effect of argon blowing into a steel stream on the stability of continuous casting is studied. Physical modeling and mathematical simulation are performed to find the parameters of argon blowing...