Sławomir Wilczewski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sławomir Wilczewski has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
- Katarzyna Skórczewska
Faculty of Chemical Technology and Engineering, Bydgoszcz University of Technology, 3 Seminaryjna Street, 85-326 Bydgoszcz, Poland
16 shared publications - Krzysztof Lewandowski
Faculty of Chemical Technology and Engineering, Bydgoszcz University of Technology, 3 Seminaryjna Street, 85-326 Bydgoszcz, Poland
13 shared publications - Magdalena Osial
Institute of Fundamental Technological Research, Polish Academy of Sciences, Warsaw, Poland
11 shared publications - Jolanta Tomaszewska
Bydgoszcz University of Science and Technology, Faculty of Chemical Technology and Engineering, Seminaryjna 3, 85-326 Bydgoszcz, Poland
6 shared publications - Joanna Szulc
Faculty of Chemical Technology and Engineering, Bydgoszcz University of Science and Technology, Seminaryjna 3, 85-326 Bydgoszcz, Poland
5 shared publications - Michael Giersig
Department of Theory of Continuous Media and Nanostructures Institute of Fundamental Technological Research Polish Academy of Sciences A. Pawińskiego 5B Warsaw Poland
5 shared publications
Latest Publications
- 1 January 2026
- Published by Polish Chemical Society in Wiadomości Chemiczne
- Vol. 7-8, 1269-1296
HISTORIA, KTÓRA TWORZY PRZYSZŁOŚĆ: POLI(CHLOREK WINYLU) W BADANIACH PRACOWNIKÓW WYDZIAŁU TECHNOLOGII I INŻYNIERII CHEMICZNEJ PBŚ
This paper presents the development of research on poly(vinyl chloride) (PVC) conducted at the Department of Polymer Technology and Protective Coatings at the Faculty of Chemical Technology and Engineering. The evolving research directions are discussed – from fundamental issues related to PVC grain morphology and the gelation process, through analysis of the impact of processing conditions on the functional properties of materials, to the development of advanced composite and coating systems. The results of studies on PVC composites, including systems with lignocellulosic fillers (WPC), carbon nanofillers (CNT, graphene), and silicon compounds, are presented. Their significant impact on the mechanical, thermal, and processing properties of the materials is demonstrated. A significant part of the paper consists of research on PVC plastisols and coating materials, including the development of compositions with autoadhesive properties, the modification of dispersion systems, and the development of color and functional coatings. The modification of polymer dispersions and the use of metal nanoparticles to impart biocidal properties to materials are also discussed. The presented results indicate that PVC remains a versatile engineering material whose properties can be broadly influenced by the selection of composition, processing conditions, and the type of modifiers. The achievements of the Department of Polymer Technology and Protective Coatings confirm its significant contribution to the advancement of PVC science and the technology of polymer materials and protective coatings.
- 1 January 2026
- Published by Polish Chemical Society in Wiadomości Chemiczne
- Vol. 7-8, 1269-1296
HISTORIA, KTÓRA TWORZY PRZYSZŁOŚĆ: POLI(CHLOREK WINYLU) W BADANIACH PRACOWNIKÓW WYDZIAŁU TECHNOLOGII I INŻYNIERII CHEMICZNEJ PBŚ
This paper presents the development of research on poly(vinyl chloride) (PVC) conducted at the Department of Polymer Technology and Protective Coatings at the Faculty of Chemical Technology and Engineering. The evolving research directions are discussed – from fundamental issues related to PVC grain morphology and the gelation process, through analysis of the impact of processing conditions on the functional properties of materials, to the development of advanced composite and coating systems. The results of studies on PVC composites, including systems with lignocellulosic fillers (WPC), carbon nanofillers (CNT, graphene), and silicon compounds, are presented. Their significant impact on the mechanical, thermal, and processing properties of the materials is demonstrated. A significant part of the paper consists of research on PVC plastisols and coating materials, including the development of compositions with autoadhesive properties, the modification of dispersion systems, and the development of color and functional coatings. The modification of polymer dispersions and the use of metal nanoparticles to impart biocidal properties to materials are also discussed. The presented results indicate that PVC remains a versatile engineering material whose properties can be broadly influenced by the selection of composition, processing conditions, and the type of modifiers. The achievements of the Department of Polymer Technology and Protective Coatings confirm its significant contribution to the advancement of PVC science and the technology of polymer materials and protective coatings.
- 1 January 2026
- Published by Polish Chemical Society in Wiadomości Chemiczne
- Vol. 7-8, 1269-1296
HISTORIA, KTÓRA TWORZY PRZYSZŁOŚĆ: POLI(CHLOREK WINYLU) W BADANIACH PRACOWNIKÓW WYDZIAŁU TECHNOLOGII I INŻYNIERII CHEMICZNEJ PBŚ
This paper presents the development of research on poly(vinyl chloride) (PVC) conducted at the Department of Polymer Technology and Protective Coatings at the Faculty of Chemical Technology and Engineering. The evolving research directions are discussed – from fundamental issues related to PVC grain morphology and the gelation process, through analysis of the impact of processing conditions on the functional properties of materials, to the development of advanced composite and coating systems. The results of studies on PVC composites, including systems with lignocellulosic fillers (WPC), carbon nanofillers (CNT, graphene), and silicon compounds, are presented. Their significant impact on the mechanical, thermal, and processing properties of the materials is demonstrated. A significant part of the paper consists of research on PVC plastisols and coating materials, including the development of compositions with autoadhesive properties, the modification of dispersion systems, and the development of color and functional coatings. The modification of polymer dispersions and the use of metal nanoparticles to impart biocidal properties to materials are also discussed. The presented results indicate that PVC remains a versatile engineering material whose properties can be broadly influenced by the selection of composition, processing conditions, and the type of modifiers. The achievements of the Department of Polymer Technology and Protective Coatings confirm its significant contribution to the advancement of PVC science and the technology of polymer materials and protective coatings.
- 1 January 2026
- Published by Polish Chemical Society in Wiadomości Chemiczne
- Vol. 7-8, 1269-1296
HISTORIA, KTÓRA TWORZY PRZYSZŁOŚĆ: POLI(CHLOREK WINYLU) W BADANIACH PRACOWNIKÓW WYDZIAŁU TECHNOLOGII I INŻYNIERII CHEMICZNEJ PBŚ
This paper presents the development of research on poly(vinyl chloride) (PVC) conducted at the Department of Polymer Technology and Protective Coatings at the Faculty of Chemical Technology and Engineering. The evolving research directions are discussed – from fundamental issues related to PVC grain morphology and the gelation process, through analysis of the impact of processing conditions on the functional properties of materials, to the development of advanced composite and coating systems. The results of studies on PVC composites, including systems with lignocellulosic fillers (WPC), carbon nanofillers (CNT, graphene), and silicon compounds, are presented. Their significant impact on the mechanical, thermal, and processing properties of the materials is demonstrated. A significant part of the paper consists of research on PVC plastisols and coating materials, including the development of compositions with autoadhesive properties, the modification of dispersion systems, and the development of color and functional coatings. The modification of polymer dispersions and the use of metal nanoparticles to impart biocidal properties to materials are also discussed. The presented results indicate that PVC remains a versatile engineering material whose properties can be broadly influenced by the selection of composition, processing conditions, and the type of modifiers. The achievements of the Department of Polymer Technology and Protective Coatings confirm its significant contribution to the advancement of PVC science and the technology of polymer materials and protective coatings.
- Open Access
Poly(vinyl chloride) Plastisol Composites with Surface-Modified Wood Flour as Potential Coating and Insulating Materials for Modern Energy-Efficient Constructions
This study investigates the development of sustainable PVC-based composites filled with surface-modified wood flour for potential use in modern, energy-efficient building systems. The aim was to enhance the mechanical performance, thermal stability, and interfacial compatibility of PVC plastisols by incorporating fine- and coarse-grained coniferous wood flour modified with silane and surfactants. Composites were formulated using emulsion PVC (Vinnolit E-2059), bis(2-ethylhexyl) adipate as a plasticizer, and MARK-17 MOK as a thermal stabilizer, and were gelled under pressure at 150 °C. Their physical, mechanical, structural, and thermal characteristics were evaluated using density and hardness measurements, SEM, thermomechanical analysis, DMA, and TGA. The results demonstrated that composites containing fine-grained, silane-treated wood flour (Lignocel C-120) exhibited the most advantageous balance of stiffness, elasticity, and thermal resistance, attributable to improved polymer–wood interfacial adhesion. The findings confirm the potential of modified wood flour as an effective bio-based filler enabling the design of durable, thermally stable coating and insulating materials with reduced environmental impact. The proposed composites may serve as protective, bonding, or insulating layers in sustainable construction, supporting the development of innovative, wood-based materials for low-carbon building applications.
Open AccessPoly(vinyl chloride) Plastisol Composites with Surface-Modified Wood Flour as Potential Coating and Insulating Materials for Modern Energy-Efficient Constructions
This study investigates the development of sustainable PVC-based composites filled with surface-modified wood flour for potential use in modern, energy-efficient building systems. The aim was to enhance the mechanical performance, thermal stability, and interfacial compatibility of PVC plastisols by incorporating fine- and coarse-grained coniferous wood flour modified with silane and surfactants. Composites were formulated using emulsion PVC (Vinnolit E-2059), bis(2-ethylhexyl) adipate as a plasticizer, and MARK-17 MOK as a thermal stabilizer, and were gelled under pressure at 150 °C. Their physical, mechanical, structural, and thermal characteristics were evaluated using density and hardness measurements, SEM, thermomechanical analysis, DMA, and TGA. The results demonstrated that composites containing fine-grained, silane-treated wood flour (Lignocel C-120) exhibited the most advantageous balance of stiffness, elasticity, and thermal resistance, attributable to improved polymer–wood interfacial adhesion. The findings confirm the potential of modified wood flour as an effective bio-based filler enabling the design of durable, thermally stable coating and insulating materials with reduced environmental impact. The proposed composites may serve as protective, bonding, or insulating layers in sustainable construction, supporting the development of innovative, wood-based materials for low-carbon building applications.
- Open Access
Utilization of Ground Eggshell as a Biofiller of Plasticized PVC-Based Materials Fabricated Using Melt Blending
The paper examines the use of waste eggshells as a valuable biofiller for modifying plasticized poly(vinyl chloride) (PVC). The raw ES was characterized using TGA, FTIR, particle size analysis, and XRD. The effects of ES on the processing, mechanical and thermal properties, density, porosity, and colour of PVC matrix composites were evaluated compared to pPVC/CC produced using the same methodology. It was found that pPVC/ES exhibits different processing properties to pPVC/CC. The mechanical properties of PVC/ES are slightly lower than those of pPVC/CC at concentrations up to 20 phr. However, at 30 phr and 40 phr, the differences in the mechanical properties of composites with both CC and ES are very similar, and the values are within the designated standard deviation of the measurement. The mechanical properties of PVC/ES do not limit their potential applications. When using eggshell (ES) as a filler, improvements in tensile strength (tts) were observed, ranging from 38% to 61% compared to the unfilled matrix and from 35% to 54% compared to pPVC/CC with an equivalent amount of filler. Although ground eggshells have similar insulating properties to calcium carbonate (CC), they are more effective at scavenging chlorine (Cl•) released during the initial stages of decomposition. This effectiveness helps to slow down the breakdown of PVC, as the eggshells maintain their porous, sponge-like structure when used as a filler.
Open AccessUtilization of Ground Eggshell as a Biofiller of Plasticized PVC-Based Materials Fabricated Using Melt Blending
The paper examines the use of waste eggshells as a valuable biofiller for modifying plasticized poly(vinyl chloride) (PVC). The raw ES was characterized using TGA, FTIR, particle size analysis, and XRD. The effects of ES on the processing, mechanical and thermal properties, density, porosity, and colour of PVC matrix composites were evaluated compared to pPVC/CC produced using the same methodology. It was found that pPVC/ES exhibits different processing properties to pPVC/CC. The mechanical properties of PVC/ES are slightly lower than those of pPVC/CC at concentrations up to 20 phr. However, at 30 phr and 40 phr, the differences in the mechanical properties of composites with both CC and ES are very similar, and the values are within the designated standard deviation of the measurement. The mechanical properties of PVC/ES do not limit their potential applications. When using eggshell (ES) as a filler, improvements in tensile strength (tts) were observed, ranging from 38% to 61% compared to the unfilled matrix and from 35% to 54% compared to pPVC/CC with an equivalent amount of filler. Although ground eggshells have similar insulating properties to calcium carbonate (CC), they are more effective at scavenging chlorine (Cl•) released during the initial stages of decomposition. This effectiveness helps to slow down the breakdown of PVC, as the eggshells maintain their porous, sponge-like structure when used as a filler.
- Open Access
Incorporation of Nanostructural Hydroxyapatite and Curcumin Extract from Curcuma longa L. Rhizome into Polylactide to Obtain Green Composite
This study showed that a polylactide (PLA)-based composite filled with nanostructured hydroxyapatite (HAp) and a natural extract from the rhizome of Curcuma longa L. could provide an alternative to commonly used fossil-based plasticsfor food packaging. The incorporation of HAp into the PLA matrix had a positive effect on improving selected properties of the composites; the beneficial effect could be enhanced by introducing a green modifier in the form of an extract. Prior to the fabrication of the composite, the filler was characterized in terms of morphology and composition, and the composite was then fully characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), Raman and Fourier transform infrared spectroscopy (FT-IR), and the mechanical, thermal, thermomechanical, and optical properties were investigated. The proposed material exhibits antioxidant properties against DPPH radicals and antibacterial performance against Escherichia coli (E. coli). The results showed that the nanocomposite has the highest antioxidant and antibacterial properties for 10 wt% HAp with an average diameter of rod-shaped structures below 100 nm. In addition, the introduction of turmeric extract had a positive effect on the tensile strength of the nanocomposites containing 1 and 5% HAp. As the resulting material adsorbs light in a specific wavelength range, it can be used in the medical sector, food-packaging, or coatings.
Open AccessIncorporation of Nanostructural Hydroxyapatite and Curcumin Extract from Curcuma longa L. Rhizome into Polylactide to Obtain Green Composite
This study showed that a polylactide (PLA)-based composite filled with nanostructured hydroxyapatite (HAp) and a natural extract from the rhizome of Curcuma longa L. could provide an alternative to commonly used fossil-based plasticsfor food packaging. The incorporation of HAp into the PLA matrix had a positive effect on improving selected properties of the composites; the beneficial effect could be enhanced by introducing a green modifier in the form of an extract. Prior to the fabrication of the composite, the filler was characterized in terms of morphology and composition, and the composite was then fully characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), Raman and Fourier transform infrared spectroscopy (FT-IR), and the mechanical, thermal, thermomechanical, and optical properties were investigated. The proposed material exhibits antioxidant properties against DPPH radicals and antibacterial performance against Escherichia coli (E. coli). The results showed that the nanocomposite has the highest antioxidant and antibacterial properties for 10 wt% HAp with an average diameter of rod-shaped structures below 100 nm. In addition, the introduction of turmeric extract had a positive effect on the tensile strength of the nanocomposites containing 1 and 5% HAp. As the resulting material adsorbs light in a specific wavelength range, it can be used in the medical sector, food-packaging, or coatings.
- Open Access
Multiscale Carbon Fibre–Carbon Nanotube Composites of Poly(Vinyl Chloride)—An Evaluation of Their Properties and Structure
To date, there has been limited information in the literature on the application of carbon fibre-carbon nanotube systems for the modification of poly(vinyl chloride) (PVC) matrixes by micro- and nanometric fillers and an evaluation of the properties of the unique materials produced. This paper presents the results of newly designed unique multiscale composites. The advantages of the simultaneous use of carbon fibres (CFs) and carbon nanotubes (CNTs) in PVC modification are discussed. To increase the dispersibility of the nanofiller, CFs together with nanotubes were subjected to a sonication process. The resulting material was introduced into PVC blends, which were processed by extrusion. The ratio of components in the hybrid filler with CF_CNT was 20:1, and its proportion in the PVC matrix was 1, 5, and 10 wt.%, respectively. Comparatively, PVC composites modified only with carbon fibres were obtained. The structure, thermal, electrical, and mechanical properties and swelling resistance of the composites were studied. The study showed a favourable homogeneous dispersion of nanotubes in the PVC matrix. This enabled effective modification of the structure at the nanometric level and the formation of an interpenetrating network of well-dispersed hybrid filler, as evidenced by a decrease in volume resistivity and improvement in swelling resistance, as well as an increase in glass transition temperature in the case of PVC/CF_CNT composites.
Open AccessMultiscale Carbon Fibre–Carbon Nanotube Composites of Poly(Vinyl Chloride)—An Evaluation of Their Properties and Structure
To date, there has been limited information in the literature on the application of carbon fibre-carbon nanotube systems for the modification of poly(vinyl chloride) (PVC) matrixes by micro- and nanometric fillers and an evaluation of the properties of the unique materials produced. This paper presents the results of newly designed unique multiscale composites. The advantages of the simultaneous use of carbon fibres (CFs) and carbon nanotubes (CNTs) in PVC modification are discussed. To increase the dispersibility of the nanofiller, CFs together with nanotubes were subjected to a sonication process. The resulting material was introduced into PVC blends, which were processed by extrusion. The ratio of components in the hybrid filler with CF_CNT was 20:1, and its proportion in the PVC matrix was 1, 5, and 10 wt.%, respectively. Comparatively, PVC composites modified only with carbon fibres were obtained. The structure, thermal, electrical, and mechanical properties and swelling resistance of the composites were studied. The study showed a favourable homogeneous dispersion of nanotubes in the PVC matrix. This enabled effective modification of the structure at the nanometric level and the formation of an interpenetrating network of well-dispersed hybrid filler, as evidenced by a decrease in volume resistivity and improvement in swelling resistance, as well as an increase in glass transition temperature in the case of PVC/CF_CNT composites.
- Open Access
- 20 February 2024
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 69 (2) , 86-91
Mechanical and thermal properties of rigid PVC and graphene nanocomposites obtained by melt–mixing
The effect of graphene (0.01, 0.1, 0.5 and 1 wt%) on the mechanical properties and thermal stability of rigid PVC was investigated. The morphology and thermal properties were analyzed by scanning electron microscopy (SEM) and thermogravimetric thermal analysis (TGA). Additionally, tensile properties, impact strength and hardness were determined. It was found that the addition of graphene can increase the impact strength and hardness and extend the thermal stability time of PVC.
- 20 February 2024
- Published by LUKASIEWICZ Research Network - Industrial Chemistry Research Institute in Polimery
- Vol. 69 (2) , 86-91
Open AccessMechanical and thermal properties of rigid PVC and graphene nanocomposites obtained by melt–mixing
The effect of graphene (0.01, 0.1, 0.5 and 1 wt%) on the mechanical properties and thermal stability of rigid PVC was investigated. The morphology and thermal properties were analyzed by scanning electron microscopy (SEM) and thermogravimetric thermal analysis (TGA). Additionally, tensile properties, impact strength and hardness were determined. It was found that the addition of graphene can increase the impact strength and hardness and extend the thermal stability time of PVC.
- 28 December 2023
- Published by Springer Nature in Journal of Nanoparticle Research
- Vol. 26 (1) , 1-23
One-pot synthesis of magnetic hydroxyapatite (SPION/HAp) for 5-fluorouracil delivery and magnetic hyperthermia
- 28 December 2023
- Published by Springer Nature in Journal of Nanoparticle Research
- Vol. 26 (1) , 1-23
One-pot synthesis of magnetic hydroxyapatite (SPION/HAp) for 5-fluorouracil delivery and magnetic hyperthermia
- Open Access
Nanohydroxyapatite Loaded with 5-Fluorouracil and Calendula officinalis L. Plant Extract Rich in Myo-Inositols for Treatment of Ovarian Cancer Cells
In this study, the hydroxyapatite (HAp) in the form of nanoparticles was synthesized through the wet co-precipitation method and loaded with plant extract from Calendula officinalis L. rich in biologically active myo-inositol, and the 5-fluorouracil anticancer drug. The obtained nanomaterials have rod-like structures approx. 30 nm in diameter and 100 nm in length. FT-IR analysis results proved the immobilization of biologically active compounds. The loading of plant extract into the carrier improved the stability of colloidal suspension, which was confirmed with turbidimetry. The composite modified with calendula extract and drug (HAp@Cal@5-flu) effectively scavenges the DPPH radicals, with a radical scavenging activity (RSA) of about 20.0 ± 1.3%. The effect is supported by the DFT calculations of the HOMO-LUMO, presenting the chemical reactivity of the molecules loaded into the HAp. The in vitro cytotoxicity results on SKOV-3 ovarian cancer cells show the pronounced cytotoxic effect of the HAp@Cal@5-flu. The calendula extract loading into the carrier provided better interactions with the tumorous biomimetic membranes studied with a Langmuir trough, making it a promising material in nano-biomedicine, including drug delivery and targeted cancer treatment.
Open AccessNanohydroxyapatite Loaded with 5-Fluorouracil and Calendula officinalis L. Plant Extract Rich in Myo-Inositols for Treatment of Ovarian Cancer Cells
In this study, the hydroxyapatite (HAp) in the form of nanoparticles was synthesized through the wet co-precipitation method and loaded with plant extract from Calendula officinalis L. rich in biologically active myo-inositol, and the 5-fluorouracil anticancer drug. The obtained nanomaterials have rod-like structures approx. 30 nm in diameter and 100 nm in length. FT-IR analysis results proved the immobilization of biologically active compounds. The loading of plant extract into the carrier improved the stability of colloidal suspension, which was confirmed with turbidimetry. The composite modified with calendula extract and drug (HAp@Cal@5-flu) effectively scavenges the DPPH radicals, with a radical scavenging activity (RSA) of about 20.0 ± 1.3%. The effect is supported by the DFT calculations of the HOMO-LUMO, presenting the chemical reactivity of the molecules loaded into the HAp. The in vitro cytotoxicity results on SKOV-3 ovarian cancer cells show the pronounced cytotoxic effect of the HAp@Cal@5-flu. The calendula extract loading into the carrier provided better interactions with the tumorous biomimetic membranes studied with a Langmuir trough, making it a promising material in nano-biomedicine, including drug delivery and targeted cancer treatment.
- Open Access
Composite of Poly(Vinyl Chloride) Plastisol and Wood Flour as a Potential Coating Material
This paper presents the results of a study of the properties of a new composite material made from poly(vinyl chloride) plastisol (PVC) and conifer-derived wood flour. The material can be used for thermal insulation, floor coverings with high resistance to mechanical trauma, and protective coatings. The plastisol was made from emulsion poly(vinyl chloride), the plasticiser was bis(2-ethylhexyl) adipate, and the stabiliser was octyltin mercapeptide. Two types of flour were used: fine-grained and coarse-grained. Its properties, such as bulk density, oil number, and plasticiser number, were determined. The polymer-wood composite contained 20 or 30 wt.% wood flour in PVC. Plastisol was obtained by repeated mixing, mashing, and venting under vacuum. The produced composite material was gelated at temperatures of 130, 150, and 170 °C. The gelation process of the composites was studied in a Brabender apparatus. Samples in the form of polymer films were used to study density, hardness, thermal stability, and mechanical and thermomechanical properties. The structure of the composites was observed by scanning electron microscopy (SEM). A summary of all test results showed that composite films made from PVC plastisol with 20 wt.% of fine wood flour gelled at 150 °C had the most favourable physical, mechanical, and thermal properties.
Open AccessComposite of Poly(Vinyl Chloride) Plastisol and Wood Flour as a Potential Coating Material
This paper presents the results of a study of the properties of a new composite material made from poly(vinyl chloride) plastisol (PVC) and conifer-derived wood flour. The material can be used for thermal insulation, floor coverings with high resistance to mechanical trauma, and protective coatings. The plastisol was made from emulsion poly(vinyl chloride), the plasticiser was bis(2-ethylhexyl) adipate, and the stabiliser was octyltin mercapeptide. Two types of flour were used: fine-grained and coarse-grained. Its properties, such as bulk density, oil number, and plasticiser number, were determined. The polymer-wood composite contained 20 or 30 wt.% wood flour in PVC. Plastisol was obtained by repeated mixing, mashing, and venting under vacuum. The produced composite material was gelated at temperatures of 130, 150, and 170 °C. The gelation process of the composites was studied in a Brabender apparatus. Samples in the form of polymer films were used to study density, hardness, thermal stability, and mechanical and thermomechanical properties. The structure of the composites was observed by scanning electron microscopy (SEM). A summary of all test results showed that composite films made from PVC plastisol with 20 wt.% of fine wood flour gelled at 150 °C had the most favourable physical, mechanical, and thermal properties.