Vasilii V. Mukhin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vasilii V. Mukhin has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Aitalina Alekseevna Okhlopkova
Chemical Department, Institute of Natural Sciences, North-Eastern Federal University, Yakutsk 677000, Russia
2 shared publications - Ee Le Shim
School of Mechanical & Automotive Engineering, Halla University, Wonju 220-712, Korea
2 shared publications - Natalia N. Petrova
Department of Chemistry, North-Eastern Federal University, 677000 Yakutsk, Russia
2 shared publications - Alexei V. Morozov
Ishlinsky Institute for Problems in Mechanics RAS, 119526 Moscow, Russia
1 shared publication - Egor A. Kapitonov
Department of Chemistry, North-Eastern Federal University, 677000 Yakutsk, Russia
1 shared publication - Iuliia Valerievna Kapitonova
Institute of Natural Sciences, North-Eastern Federal University, Yakutsk, Russia
1 shared publication
Latest Publications
- Open Access
Morphology Analysis of Friction Surfaces of Composites Based on PTFE and Layered Silicates
In the present study, the tribological behavior of polytetrafluoroethylene (PTFE) composites filled with natural layered silicates (LS) was investigated. The change in the morphology of the friction surface of composites depending on the content and chemical composition of layered silicates has been shown. The friction surface of PTFE composites with layered silicates was investigated by scanning electron microscopy (SEM). The formation on the friction surface of a special layer with a structure different from the bulk of the polymer, which is formed from particles of fillers and wear products, has been established. The thickness of this layer is independent of the content of layered silicates in the polymer. It was indicated that wear debris of PTFE composites was assembled during friction and uniformly cover the friction surface layer by layer, thereby forming a protective layer.
Open AccessMorphology Analysis of Friction Surfaces of Composites Based on PTFE and Layered Silicates
In the present study, the tribological behavior of polytetrafluoroethylene (PTFE) composites filled with natural layered silicates (LS) was investigated. The change in the morphology of the friction surface of composites depending on the content and chemical composition of layered silicates has been shown. The friction surface of PTFE composites with layered silicates was investigated by scanning electron microscopy (SEM). The formation on the friction surface of a special layer with a structure different from the bulk of the polymer, which is formed from particles of fillers and wear products, has been established. The thickness of this layer is independent of the content of layered silicates in the polymer. It was indicated that wear debris of PTFE composites was assembled during friction and uniformly cover the friction surface layer by layer, thereby forming a protective layer.
- Open Access
Enhanced Physical and Mechanical Properties of Nitrile-Butadiene Rubber Composites with N-Cetylpyridinium Bromide-Carbon Black
The physical and mechanical properties of nitrile–butadiene rubber (NBR) composites with N-cetylpyridinium bromide-carbon black (CPB-CB) were investigated. Addition of 5 parts per hundred rubber (phr) of CPB-CB into NBR improved the tensile strength by 124%, vulcanization rate by 41%, shore hardness by 15%, and decreased the volumetric wear by 7% compared to those of the base rubber-CB composite.
Open AccessEnhanced Physical and Mechanical Properties of Nitrile-Butadiene Rubber Composites with N-Cetylpyridinium Bromide-Carbon Black
The physical and mechanical properties of nitrile–butadiene rubber (NBR) composites with N-cetylpyridinium bromide-carbon black (CPB-CB) were investigated. Addition of 5 parts per hundred rubber (phr) of CPB-CB into NBR improved the tensile strength by 124%, vulcanization rate by 41%, shore hardness by 15%, and decreased the volumetric wear by 7% compared to those of the base rubber-CB composite.
- Open Access
- 1 January 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1431 (1) , 012036
Evaluation of the performance of sealing rubbers operated in conditions of abrasive wear and low temperatures
The studied materials based on the new rubbers of unique frost resistance -propylene oxide rubber (Tg = -74 °C) and Hydrin T6000 epichlorohydrin rubber are recommended to be used as static and dynamic sealing parts for the equipment operated in the North. This was based on the full-scale tests in cold climates (Republic of Sakha (Yakutia)) and evaluation of tribological characteristics (coefficient of friction) at negative temperatures. The standard techniques were used in assessing of the changes of the physical and mechanical, relaxation, and low-temperature characteristics of model rubbers after aging. A special testing unit and a method for conducting the tests were developed to estimate the coefficient of friction at low temperatures.
- 1 January 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1431 (1) , 012036
Open AccessEvaluation of the performance of sealing rubbers operated in conditions of abrasive wear and low temperatures
The studied materials based on the new rubbers of unique frost resistance -propylene oxide rubber (Tg = -74 °C) and Hydrin T6000 epichlorohydrin rubber are recommended to be used as static and dynamic sealing parts for the equipment operated in the North. This was based on the full-scale tests in cold climates (Republic of Sakha (Yakutia)) and evaluation of tribological characteristics (coefficient of friction) at negative temperatures. The standard techniques were used in assessing of the changes of the physical and mechanical, relaxation, and low-temperature characteristics of model rubbers after aging. A special testing unit and a method for conducting the tests were developed to estimate the coefficient of friction at low temperatures.
- Open Access
Preparation and Improved Physical Characteristics of Propylene Oxide Rubber Composites
Sealing rubbers employed in cold climates such as the Siberian Arctic must be able to withstand temperatures as low as −50 °C while still exhibiting specific relaxation, strength, tribological characteristics, and a resistance to aggressive media. Previous investigations of propylene oxide rubber (SKPO, Tg = −73 °C) modified with polytetrafluoroethylene (PTFE) have revealed that, while the rubber composite materials exhibit double the wear resistance compared to unmodified polypropylene oxide rubber, they have poor frost resistance. In the present study, we developed materials based on SKPO and ultrafine PTFE (UPTFE), which can be characterized by its smaller particle size, low molecular weight, high tribo-technical characteristics, and resistance to aggressive media. The properties of the rubber composites were evaluated using the standard methods. The structures of the materials were investigated by electron microscopy and XRD analysis. It was shown that the materials have excellent wear resistance, resistance to aggressive media, compression set, and low-temperature resistance. The addition of UPTFE is preferable to the addition of PTFE because the desired positive effects can be attained with only 0.5–1 parts per hundred parts of rubber (phr) UPTFE while 20 phr PTFE would be necessary.
Open AccessPreparation and Improved Physical Characteristics of Propylene Oxide Rubber Composites
Sealing rubbers employed in cold climates such as the Siberian Arctic must be able to withstand temperatures as low as −50 °C while still exhibiting specific relaxation, strength, tribological characteristics, and a resistance to aggressive media. Previous investigations of propylene oxide rubber (SKPO, Tg = −73 °C) modified with polytetrafluoroethylene (PTFE) have revealed that, while the rubber composite materials exhibit double the wear resistance compared to unmodified polypropylene oxide rubber, they have poor frost resistance. In the present study, we developed materials based on SKPO and ultrafine PTFE (UPTFE), which can be characterized by its smaller particle size, low molecular weight, high tribo-technical characteristics, and resistance to aggressive media. The properties of the rubber composites were evaluated using the standard methods. The structures of the materials were investigated by electron microscopy and XRD analysis. It was shown that the materials have excellent wear resistance, resistance to aggressive media, compression set, and low-temperature resistance. The addition of UPTFE is preferable to the addition of PTFE because the desired positive effects can be attained with only 0.5–1 parts per hundred parts of rubber (phr) UPTFE while 20 phr PTFE would be necessary.