Colin P. O’bAnion
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Colin P. O’bAnion has a total of 134 co-authors. Here are the top co-authors by number of shared publications:
- David Sinton
Department of Mechanical and Industrial Engineering, University of Toronto, Toronto, Ontario, M5S 3G8, Canada
17 shared publications - Edward Hartley Sargent
Department of electrical and computer engineering, University of Toronto, Toronto, Ontario, M5S 3G4, Canada
13 shared publications - Rui Kai Miao
Department of Mechanical and Industrial Engineering, University of Toronto, Toronto, Canada
12 shared publications - Christine Marie Gabardo
University of Toronto
10 shared publications Adnan Ozden
Department of Mechanical and Industrial Engineering, University of Toronto, Toronto, Canada
8 shared publicationsJianan Erick Huang
Department of Electrical and Computer Engineering, University of Toronto, Toronto, Canada
8 shared publications
Latest Publications
- Open Access
- 3 March 2026
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 32 (2)
EDX Array Tomography: 3D Imaging With Chemical Sensitivity and Submicron Resolution Through Ultramicrotomy and SEM-EDX Mapping
Elemental contrast from energy-dispersive X-ray spectroscopy (EDX) provides valuable insights into various materials and samples. However, this surface-mapping technique suffers from poor depth resolution, which prevents a straightforward application to tomographic reconstruction. Additionally, due to charge artifacts or beam damage, this technique is often limited to electrically conductive samples, which does not allow its use on multiphase samples with low conductivity and complex 3D geometries. We developed an adaptation of array tomography using an automated tape-collecting ultramicrotome (ATUMtome) and scanning electron microscopy with EDX mapping to enable tomographic imaging of polymer-containing multiphase samples at submicron resolution. Hence, this method overcomes the limited depth resolution of EDX mapping, and by surface-coating the sections before imaging, charging artifacts are mitigated. Recently, we demonstrated the utility of the technique by applying it to a multiphase microporous layer encountered in a CO2 electrolyzer gas diffusion electrode, which could not be imaged using conventional tomographic approaches. A digital model of the full electrode was obtained in combination with focused ion beam scanning electron microscopy tomography and X-ray microtomography. Here, we describe the process of EDX array tomography in detail and elucidate the advantages of the technique in the field of energy materials.
- 3 March 2026
- Published by Oxford University Press (OUP) in Microscopy and Microanalysis
- Vol. 32 (2)
Open AccessEDX Array Tomography: 3D Imaging With Chemical Sensitivity and Submicron Resolution Through Ultramicrotomy and SEM-EDX Mapping
Elemental contrast from energy-dispersive X-ray spectroscopy (EDX) provides valuable insights into various materials and samples. However, this surface-mapping technique suffers from poor depth resolution, which prevents a straightforward application to tomographic reconstruction. Additionally, due to charge artifacts or beam damage, this technique is often limited to electrically conductive samples, which does not allow its use on multiphase samples with low conductivity and complex 3D geometries. We developed an adaptation of array tomography using an automated tape-collecting ultramicrotome (ATUMtome) and scanning electron microscopy with EDX mapping to enable tomographic imaging of polymer-containing multiphase samples at submicron resolution. Hence, this method overcomes the limited depth resolution of EDX mapping, and by surface-coating the sections before imaging, charging artifacts are mitigated. Recently, we demonstrated the utility of the technique by applying it to a multiphase microporous layer encountered in a CO2 electrolyzer gas diffusion electrode, which could not be imaged using conventional tomographic approaches. A digital model of the full electrode was obtained in combination with focused ion beam scanning electron microscopy tomography and X-ray microtomography. Here, we describe the process of EDX array tomography in detail and elucidate the advantages of the technique in the field of energy materials.
- Open Access
- 15 April 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-9
A redox-active polymeric network facilitates electrified reactive-capture electrosynthesis to multi-carbon products from dilute CO2-containing streams
Reactive capture – the integration of CO2 capture with electrochemical upgrade – offers the prospect of improving overall energy efficiency in captured-CO2-to-fuels by eliminating the gas-phase CO2 desorption step, and by further offering a CO2-free gas product stream. Two related challenges limit the potential impact of electrified reactive capture today: its propensity to produce lower-value C1 products (carbon products containing one carbon atom per molecule); and its failure to retain performance when fed dilute streams (e.g. ~1-10% CO2). We posit that these could be addressed using catalysts that locally concentrate and activate in-situ generated CO2: we integrate a redox-active polymeric network whose polymer fragments undergo reversible reduction during the electrochemical conversion process, enabling electron transfer to CO2 molecules generated in-situ from carbonate capture liquid. We report as a result a 55 ± 5% C2+ (carbon products containing two or more carbon atoms per molecule) Faradaic efficiency (FE) at 300 mA/cm2 in an electrochemical reactive capture system in which the electrolysis stage is fed with 1 M K2CO3. We obtain 56 ± 4 wt% C2H4 in the product gas stream. When we use a dilute stream consisting of 1% CO2 in N2 at the KOH capture stage, we retain the C2+ FE to within 85% (relative) of its value achieved in the case of pure CO2.
- 15 April 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-9
Open AccessA redox-active polymeric network facilitates electrified reactive-capture electrosynthesis to multi-carbon products from dilute CO2-containing streams
Reactive capture – the integration of CO2 capture with electrochemical upgrade – offers the prospect of improving overall energy efficiency in captured-CO2-to-fuels by eliminating the gas-phase CO2 desorption step, and by further offering a CO2-free gas product stream. Two related challenges limit the potential impact of electrified reactive capture today: its propensity to produce lower-value C1 products (carbon products containing one carbon atom per molecule); and its failure to retain performance when fed dilute streams (e.g. ~1-10% CO2). We posit that these could be addressed using catalysts that locally concentrate and activate in-situ generated CO2: we integrate a redox-active polymeric network whose polymer fragments undergo reversible reduction during the electrochemical conversion process, enabling electron transfer to CO2 molecules generated in-situ from carbonate capture liquid. We report as a result a 55 ± 5% C2+ (carbon products containing two or more carbon atoms per molecule) Faradaic efficiency (FE) at 300 mA/cm2 in an electrochemical reactive capture system in which the electrolysis stage is fed with 1 M K2CO3. We obtain 56 ± 4 wt% C2H4 in the product gas stream. When we use a dilute stream consisting of 1% CO2 in N2 at the KOH capture stage, we retain the C2+ FE to within 85% (relative) of its value achieved in the case of pure CO2.
- 4 October 2024
- Published by Springer Nature in Nature Synthesis
- Vol. 4 (1) , 75-83
Carbon- and energy-efficient ethanol electrosynthesis via interfacial cation enrichment
- 4 October 2024
- Published by Springer Nature in Nature Synthesis
- Vol. 4 (1) , 75-83
Carbon- and energy-efficient ethanol electrosynthesis via interfacial cation enrichment
- Top Cited PapersOpen Access
Scalability and stability in CO2 reduction via tomography-guided system design
Top Cited PapersOpen AccessScalability and stability in CO2 reduction via tomography-guided system design
- 4 July 2024
- Published by Springer Nature in Nature Energy
- Vol. 9 (8) , 1011-1020
Improving the SO2 tolerance of CO2 reduction electrocatalysts using a polymer/catalyst/ionomer heterojunction design
- 4 July 2024
- Published by Springer Nature in Nature Energy
- Vol. 9 (8) , 1011-1020
Improving the SO2 tolerance of CO2 reduction electrocatalysts using a polymer/catalyst/ionomer heterojunction design
- 29 May 2024
- Published by Springer Nature in Nature Sustainability
- Vol. 7 (7) , 931-937
Efficient CO and acrolein co-production via paired electrolysis
- 29 May 2024
- Published by Springer Nature in Nature Sustainability
- Vol. 7 (7) , 931-937
Efficient CO and acrolein co-production via paired electrolysis
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (47) , 2401
Early Failure Detection for CO2 Reduction Electrolyzers Via in-Line Electrochemical Impedance Spectroscopy
The electrochemical CO2 reduction reaction (CO2RR) presents the opportunity to produce chemical feedstocks and fuels directly from CO2. Recent achievements in energy efficiency and current density are approaching the targets required for commercial viability; however, stability remains more than two orders of magnitude below the required 80,000 h. In CO2RR there is a challenge to distinguish the cause of failure among many possibilities. Failure can result from initial setup (e.g. over or under compression of the membrane and electrodes), gradual degradation of components (e.g. cathode and anode catalyst restructuring and dissolution), accumulation of products or byproducts (e.g. alcohols or salt accumulation), or immediate failures (e.g. a hole in the membrane or a short circuit). These failure modes must be addressed to reach the targeted stability needed for the wide-scale adoption of this technology. Early identification and mitigation of these failures would increase the electrolyzer lifetime and the commercial viability of CO2RR electrolyzers. Current techniques to characterize failures of the electrolyzer rely on post-mortem analysis of cell components. The analysis of individual components after operation may not accurately reflect their state in operando. There are techniques that are capable of analyzing the cell in operation (e.g. XAS, Raman, and TEM), but these typically require modified cell architectures and are operated at lower reaction rates. To effectively diagnose failure, the analysis technique should be applied to electrolyzers operating under realistic conditions. Here we implement an in-line real-time electrochemical impedance spectroscopy (EIS) technique to monitor CO2RR electrolyzers during operation. EIS is a non-destructive technique that can provide continuous information on the performance of specific components within the electrolyzer. We characterize common failure modes, such as poor compression, salt formation, catalyst degradation, and short circuits, and their identifying changes to the EIS response. We extract key electrochemical parameters from the EIS response and use them to develop a framework to identify and prevent the most common failure modes. Among other applications, this framework allowed for the detection of anode catalyst degradation 11 h before other indicators, such as cell voltage or product selectivity. This technique and framework can be applied to monitor CO2 electrolyzers as they are scaled and stacked.
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (47) , 2401
Early Failure Detection for CO2 Reduction Electrolyzers Via in-Line Electrochemical Impedance Spectroscopy
The electrochemical CO2 reduction reaction (CO2RR) presents the opportunity to produce chemical feedstocks and fuels directly from CO2. Recent achievements in energy efficiency and current density are approaching the targets required for commercial viability; however, stability remains more than two orders of magnitude below the required 80,000 h. In CO2RR there is a challenge to distinguish the cause of failure among many possibilities. Failure can result from initial setup (e.g. over or under compression of the membrane and electrodes), gradual degradation of components (e.g. cathode and anode catalyst restructuring and dissolution), accumulation of products or byproducts (e.g. alcohols or salt accumulation), or immediate failures (e.g. a hole in the membrane or a short circuit). These failure modes must be addressed to reach the targeted stability needed for the wide-scale adoption of this technology. Early identification and mitigation of these failures would increase the electrolyzer lifetime and the commercial viability of CO2RR electrolyzers. Current techniques to characterize failures of the electrolyzer rely on post-mortem analysis of cell components. The analysis of individual components after operation may not accurately reflect their state in operando. There are techniques that are capable of analyzing the cell in operation (e.g. XAS, Raman, and TEM), but these typically require modified cell architectures and are operated at lower reaction rates. To effectively diagnose failure, the analysis technique should be applied to electrolyzers operating under realistic conditions. Here we implement an in-line real-time electrochemical impedance spectroscopy (EIS) technique to monitor CO2RR electrolyzers during operation. EIS is a non-destructive technique that can provide continuous information on the performance of specific components within the electrolyzer. We characterize common failure modes, such as poor compression, salt formation, catalyst degradation, and short circuits, and their identifying changes to the EIS response. We extract key electrochemical parameters from the EIS response and use them to develop a framework to identify and prevent the most common failure modes. Among other applications, this framework allowed for the detection of anode catalyst degradation 11 h before other indicators, such as cell voltage or product selectivity. This technique and framework can be applied to monitor CO2 electrolyzers as they are scaled and stacked.
- Open Access
- 25 August 2023
- Published by Wiley in ChemSusChem
- Vol. 16 (23) , e202300657
Early Warning for the Electrolyzer: Monitoring CO2 Reduction via In‐Line Electrochemical Impedance Spectroscopy
The electrochemical CO2 reduction reaction (CO2RR) to fuels and feedstocks presents an opportunity to decarbonize the chemical industry, and current electrolyzer performance levels approach commercial viability. However, stability remains below that required, in part because of the challenge of probing these electrolyzer systems in real time and the challenge of determining the root cause of failure. Failure can result from initial conditions (e. g., the over‐ or under‐compression of the electrolyzer), gradual degradation of components (e. g., cathode or anode catalysts), the accumulation of products or by‐products, or immediate changes such as the development of a hole in the membrane or a short circuit. Identifying and mitigating these assembly‐related, gradual, and immediate failure modes would increase both electrolyzer lifetime and economic viability of CO2RR. We demonstrate the continuous monitoring of CO2RR electrolyzers during operation via non‐disruptive, real‐time electrochemical impedance spectroscopy (EIS) analysis. Using this technique, we characterise common failure modes ‐ compression, salt formation, and membrane short circuits ‐ and identify electrochemical parameter signatures for each. We further propose a framework to identify, predict, and prevent failures in CO2RR electrolyzers. This framework allowed for the prediction of anode degradation ~11 hours before other indicators such as selectivity or voltage.
- 25 August 2023
- Published by Wiley in ChemSusChem
- Vol. 16 (23) , e202300657
Open AccessEarly Warning for the Electrolyzer: Monitoring CO2 Reduction via In‐Line Electrochemical Impedance Spectroscopy
The electrochemical CO2 reduction reaction (CO2RR) to fuels and feedstocks presents an opportunity to decarbonize the chemical industry, and current electrolyzer performance levels approach commercial viability. However, stability remains below that required, in part because of the challenge of probing these electrolyzer systems in real time and the challenge of determining the root cause of failure. Failure can result from initial conditions (e. g., the over‐ or under‐compression of the electrolyzer), gradual degradation of components (e. g., cathode or anode catalysts), the accumulation of products or by‐products, or immediate changes such as the development of a hole in the membrane or a short circuit. Identifying and mitigating these assembly‐related, gradual, and immediate failure modes would increase both electrolyzer lifetime and economic viability of CO2RR. We demonstrate the continuous monitoring of CO2RR electrolyzers during operation via non‐disruptive, real‐time electrochemical impedance spectroscopy (EIS) analysis. Using this technique, we characterise common failure modes ‐ compression, salt formation, and membrane short circuits ‐ and identify electrochemical parameter signatures for each. We further propose a framework to identify, predict, and prevent failures in CO2RR electrolyzers. This framework allowed for the prediction of anode degradation ~11 hours before other indicators such as selectivity or voltage.
- Top Cited Papers
- 21 August 2023
- Published by Springer Nature in Nature Catalysis
- Vol. 6 (9) , 763-772
Cationic-group-functionalized electrocatalysts enable stable acidic CO2 electrolysis
- 21 August 2023
- Published by Springer Nature in Nature Catalysis
- Vol. 6 (9) , 763-772
Top Cited PapersCationic-group-functionalized electrocatalysts enable stable acidic CO2 electrolysis
- Open Access
- 7 June 2023
- Published by Springer Nature in Nature Communications
- Vol. 14 (1) , 1-8
Single-site decorated copper enables energy- and carbon-efficient CO2 methanation in acidic conditions
Renewable CH4produced from electrocatalytic CO2reduction is viewed as a sustainable and versatile energy carrier, compatible with existing infrastructure. However, conventional alkaline and neutral CO2-to-CH4systems suffer CO2loss to carbonates, and recovering the lost CO2requires input energy exceeding the heating value of the produced CH4. Here we pursue CH4-selective electrocatalysis in acidic conditions via a coordination method, stabilizing free Cu ions by bonding Cu with multidentate donor sites. We find that hexadentate donor sites in ethylenediaminetetraacetic acid enable the chelation of Cu ions, regulating Cu cluster size and forming Cu-N/O single sites that achieve high CH4selectivity in acidic conditions. We report a CH4Faradaic efficiency of 71% (at 100 mA cm−2) with 2that results in an overall energy intensity (254 GJ/tonne CH4), half that of existing electroproduction routes.
- 7 June 2023
- Published by Springer Nature in Nature Communications
- Vol. 14 (1) , 1-8
Open AccessSingle-site decorated copper enables energy- and carbon-efficient CO2 methanation in acidic conditions
Renewable CH4produced from electrocatalytic CO2reduction is viewed as a sustainable and versatile energy carrier, compatible with existing infrastructure. However, conventional alkaline and neutral CO2-to-CH4systems suffer CO2loss to carbonates, and recovering the lost CO2requires input energy exceeding the heating value of the produced CH4. Here we pursue CH4-selective electrocatalysis in acidic conditions via a coordination method, stabilizing free Cu ions by bonding Cu with multidentate donor sites. We find that hexadentate donor sites in ethylenediaminetetraacetic acid enable the chelation of Cu ions, regulating Cu cluster size and forming Cu-N/O single sites that achieve high CH4selectivity in acidic conditions. We report a CH4Faradaic efficiency of 71% (at 100 mA cm−2) with 2that results in an overall energy intensity (254 GJ/tonne CH4), half that of existing electroproduction routes.