Cosmin Dobrea
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Cosmin Dobrea has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Ion Tiseanu
National Institute of Laser Plasma and Radiation Physics, P.O. Box MG-36, 76900 Bucharest-Magurele, Romania
3 shared publications - Mihail Lungu
National Institute for Laser, Plasma and Radiation Physics, 077125 Magurele, Romania
2 shared publications - Adrian Sima
National Institute for Laser, Plasma and Radiation Physics (INFLPR), Măgurele, 077125 Ilfov, Romania
1 shared publication - Anastasios Tzotzis
Department of Product and Systems Design Engineering, University of Western Macedonia, 50100 Kila Kozani, Greece
1 shared publication - Andrei C. Popescu
Center for Advanced Laser Technologies (CETAL), National Institute for Laser, Plasma and Radiation Physics (INFLPR), 077125 Magurele, Ilfov, Romania
1 shared publication - Catalin Tampu
Faculty of Engineering, Vasile Alecsandri University of Bacau, 600115 Bacau, Romania
1 shared publication
Latest Publications
- Open Access
- 6 August 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (8) , 937
Interlocking Interfaces for Enhanced Mechanical Properties in Bi-Component 3D Printing of Biodegradable Materials
Additive manufacturing has evolved beyond monomaterial fabrication, enabling the integration of dissimilar polymers within a single structure to achieve spatially tailored properties. In Fused Filament Fabrication (FFF), however, the discrete, layer-wise deposition and inherent material incompatibilities make the interfacial region a critical determinant of structural integrity. Rather than acting as a simple boundary, the interface governs stress transfer, damage initiation, and failure propagation, especially in biodegradable polymer systems where thermal and rheological mismatches are pronounced. This study investigates bi-component FFF structures manufactured from PLA and PLA/PHA using mechanically interlocked interface geometries (T-type and dovetail configurations). Mechanical performance was assessed through tensile, flexural, and Charpy impact testing, complemented by fracture analysis, surface topography evaluation, and X-ray Computed Tomography (XCT) for internal defect characterization. The results establish correlations between interface design, defect distribution, and overall structural response.
- 6 August 2026
- Published by MDPI AG in Micromachines
- Vol. 17 (8) , 937
Open AccessInterlocking Interfaces for Enhanced Mechanical Properties in Bi-Component 3D Printing of Biodegradable Materials
Additive manufacturing has evolved beyond monomaterial fabrication, enabling the integration of dissimilar polymers within a single structure to achieve spatially tailored properties. In Fused Filament Fabrication (FFF), however, the discrete, layer-wise deposition and inherent material incompatibilities make the interfacial region a critical determinant of structural integrity. Rather than acting as a simple boundary, the interface governs stress transfer, damage initiation, and failure propagation, especially in biodegradable polymer systems where thermal and rheological mismatches are pronounced. This study investigates bi-component FFF structures manufactured from PLA and PLA/PHA using mechanically interlocked interface geometries (T-type and dovetail configurations). Mechanical performance was assessed through tensile, flexural, and Charpy impact testing, complemented by fracture analysis, surface topography evaluation, and X-ray Computed Tomography (XCT) for internal defect characterization. The results establish correlations between interface design, defect distribution, and overall structural response.
- Open Access
Use of X-ray Computed Tomography for Assessing Defects in Ti Grade 5 Parts Produced by Laser Melting Deposition
Laser Melting Deposition (LMD) is a metal printing technique that allows for the manufacturing of large objects by Directed Energy Deposition. Due to its versatility in variation of parameters, the possibility to use two or more materials, to create alloys in situ or produce multi-layer structures, LMD is still being scientifically researched and is still far from industrial maturity. The structural testing of obtained samples can be time consuming and solutions that can decrease the samples analysis time are constantly proposed in the scientific literature. In this manuscript we present a quality improvement study for obtaining defect-free bulk samples of Ti6Al4V under X-Ray Computed Tomography (XCT) by varying the hatch spacing and distance between planes. Based on information provided by XCT, the experimental conditions were changed until complete elimination of porosity. Information on the defects in the bulk of the samples by XCT was used for feedback during parameters tuning in view of complete removal of pores. The research time was reduced to days instead of weeks or months of samples preparation and analysis by destructive metallographic techniques.
Open AccessUse of X-ray Computed Tomography for Assessing Defects in Ti Grade 5 Parts Produced by Laser Melting Deposition
Laser Melting Deposition (LMD) is a metal printing technique that allows for the manufacturing of large objects by Directed Energy Deposition. Due to its versatility in variation of parameters, the possibility to use two or more materials, to create alloys in situ or produce multi-layer structures, LMD is still being scientifically researched and is still far from industrial maturity. The structural testing of obtained samples can be time consuming and solutions that can decrease the samples analysis time are constantly proposed in the scientific literature. In this manuscript we present a quality improvement study for obtaining defect-free bulk samples of Ti6Al4V under X-Ray Computed Tomography (XCT) by varying the hatch spacing and distance between planes. Based on information provided by XCT, the experimental conditions were changed until complete elimination of porosity. Information on the defects in the bulk of the samples by XCT was used for feedback during parameters tuning in view of complete removal of pores. The research time was reduced to days instead of weeks or months of samples preparation and analysis by destructive metallographic techniques.
- Open Access
Enhanced XRF Methods for Investigating the Erosion-Resistant Functional Coatings
The development of erosion-resistant functional materials usable as plasma facing first wall components (PFC) is crucial for increasing the lifetime of future fusion reactors. Generally, PFCs have to be quality checked and characterized regarding their composition, before integrating them into the fusion reactor vessel. Enhanced X-ray fluorescence (XRF) methods represent an effective alternative to conventional analysis methods for the characterization of refractive metallic coatings on large areas of fusion materials. We have developed and applied XRF methods as fast and robust methods for the characterization of the thickness and composition uniformity of complex functional coatings. These coatings consist of tungsten included in multilayer configuration and deposited on low or high Z substrates. We have further developed customized calibration protocols for quantifying the element composition and layer thickness of each investigated sample. The calibration protocols are based on a combination of standard samples measurements, Monte Carlo simulations, and fundamental parameter theoretical calculations. The calibrated results are discussed considering a selection of relevant PFC samples. The deposition uniformity was successfully investigated for different PFC-relevant tiles and lamella shaped samples with W layers below and over the W L-line saturation thickness. Also, the 2D thickness mapping capability of the XRF method was demonstrated by studying the plasma post-erosion pattern.
Open AccessEnhanced XRF Methods for Investigating the Erosion-Resistant Functional Coatings
The development of erosion-resistant functional materials usable as plasma facing first wall components (PFC) is crucial for increasing the lifetime of future fusion reactors. Generally, PFCs have to be quality checked and characterized regarding their composition, before integrating them into the fusion reactor vessel. Enhanced X-ray fluorescence (XRF) methods represent an effective alternative to conventional analysis methods for the characterization of refractive metallic coatings on large areas of fusion materials. We have developed and applied XRF methods as fast and robust methods for the characterization of the thickness and composition uniformity of complex functional coatings. These coatings consist of tungsten included in multilayer configuration and deposited on low or high Z substrates. We have further developed customized calibration protocols for quantifying the element composition and layer thickness of each investigated sample. The calibration protocols are based on a combination of standard samples measurements, Monte Carlo simulations, and fundamental parameter theoretical calculations. The calibrated results are discussed considering a selection of relevant PFC samples. The deposition uniformity was successfully investigated for different PFC-relevant tiles and lamella shaped samples with W layers below and over the W L-line saturation thickness. Also, the 2D thickness mapping capability of the XRF method was demonstrated by studying the plasma post-erosion pattern.