Richard M. Ambrosi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Richard M. Ambrosi has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Emily Jane Watkinson
Univ Leicester, Space Pk Leicester,92 Corp Rd, Leicester LE4 5SP, England
4 shared publications Daniel P. Kramer
University of Dayton, 300 College Park, Dayton, Ohio
2 shared publications- Hugo Williams
University of Leicester
2 shared publications - Jean-François Vigier
European Commission, Joint Research Centre (JRC), Karlsruhe, Germany
2 shared publications - Ramy Mesalam
Univ Leicester, Space Pk Leicester,92 Corp Rd, Leicester LE4 5SP, England
2 shared publications Alan A. Wells
Univ. of Leicester (United Kingdom)
1 shared publication
Latest Publications
- Open Access
Thermal Properties and Behaviour of Am-Bearing Fuel in European Space Radioisotope Power Systems
The European Space Agency is funding the research and development of 241Am-bearing oxide-fuelled radioisotope power systems (RPSs) including radioisotope thermoelectric generators (RTGs) and European Large Heat Sources (ELHSs). The RPSs’ requirements include that the fuel’s maximum temperature, Tmax, must remain below its melting temperature. The current prospected fuel is (Am0.80U0.12Np0.06Pu0.02)O1.8. The fuel’s experimental heat capacity, Cp, is determined between 20 K and 1786 K based on direct low temperature heat capacity measurements and high temperature drop calorimetry measurements. The recommended high temperature equation is Cp(T/K) = 55.1189 + 3.46216 × 102 T − 4.58312 × 105 T−2 (valid up to 1786 K). The RTG/ELHS Tmax is estimated as a function of the fuel thermal conductivity, k, and the clad’s inner surface temperature, Ti cl, using a new analytical thermal model. Estimated bounds, based on conduction-only and radiation-only conditions between the fuel and clad, are established. Estimates for k (80–100% T.D.) are made using Cp, and estimates of thermal diffusivity and thermal expansion estimates of americium/uranium oxides. The lowest melting temperature of americium/uranium oxides is assumed. The lowest k estimates are assumed (80% T.D.). The highest estimated Tmax for a ‘standard operating’ RTG is 1120 K. A hypothetical scenario is investigated: an ELHS Ti cl = 1973K-the RPSs’ requirements’ maximum permitted temperature. Fuel melting will not occur.
Open AccessThermal Properties and Behaviour of Am-Bearing Fuel in European Space Radioisotope Power Systems
The European Space Agency is funding the research and development of 241Am-bearing oxide-fuelled radioisotope power systems (RPSs) including radioisotope thermoelectric generators (RTGs) and European Large Heat Sources (ELHSs). The RPSs’ requirements include that the fuel’s maximum temperature, Tmax, must remain below its melting temperature. The current prospected fuel is (Am0.80U0.12Np0.06Pu0.02)O1.8. The fuel’s experimental heat capacity, Cp, is determined between 20 K and 1786 K based on direct low temperature heat capacity measurements and high temperature drop calorimetry measurements. The recommended high temperature equation is Cp(T/K) = 55.1189 + 3.46216 × 102 T − 4.58312 × 105 T−2 (valid up to 1786 K). The RTG/ELHS Tmax is estimated as a function of the fuel thermal conductivity, k, and the clad’s inner surface temperature, Ti cl, using a new analytical thermal model. Estimated bounds, based on conduction-only and radiation-only conditions between the fuel and clad, are established. Estimates for k (80–100% T.D.) are made using Cp, and estimates of thermal diffusivity and thermal expansion estimates of americium/uranium oxides. The lowest melting temperature of americium/uranium oxides is assumed. The lowest k estimates are assumed (80% T.D.). The highest estimated Tmax for a ‘standard operating’ RTG is 1120 K. A hypothetical scenario is investigated: an ELHS Ti cl = 1973K-the RPSs’ requirements’ maximum permitted temperature. Fuel melting will not occur.
- Open Access
- 21 April 2021
- Published by Taylor & Francis in Nuclear Technology
- Vol. 207 (6) , 773-781
A Concept Study on Advanced Radioisotope Solid Solutions and Mixed-Oxide Fuel Forms for Future Space Nuclear Power Systems
Radioisotope power systems (RPSs) have transformed our ability to explore the solar system. RPSs have been in existence for almost seven decades. Most missions have utilized 238Pu as the radioisotope of choice to generate electrical power and to produce heat for the operation and thermal management of spacecraft systems. In Europe, for the past decade 241Am has been selected for RPS research programs. This paper hypothesizes that the inclusion of small quantities of relatively short-lived radioisotopes such as 232U and 244Cm, particularly when dealing with long-lived radioisotope 241Am, could have beneficial implications for future RPS designs. This paper focuses on the thermal output implications and impact on system-level design. The authors recognize that the selection of any new or modified radioisotope heat source material will require extensive research on fuel form stability, the radiological impact, cost of production, containment, and launch safety considerations.
- 21 April 2021
- Published by Taylor & Francis in Nuclear Technology
- Vol. 207 (6) , 773-781
Open AccessA Concept Study on Advanced Radioisotope Solid Solutions and Mixed-Oxide Fuel Forms for Future Space Nuclear Power Systems
Radioisotope power systems (RPSs) have transformed our ability to explore the solar system. RPSs have been in existence for almost seven decades. Most missions have utilized 238Pu as the radioisotope of choice to generate electrical power and to produce heat for the operation and thermal management of spacecraft systems. In Europe, for the past decade 241Am has been selected for RPS research programs. This paper hypothesizes that the inclusion of small quantities of relatively short-lived radioisotopes such as 232U and 244Cm, particularly when dealing with long-lived radioisotope 241Am, could have beneficial implications for future RPS designs. This paper focuses on the thermal output implications and impact on system-level design. The authors recognize that the selection of any new or modified radioisotope heat source material will require extensive research on fuel form stability, the radiological impact, cost of production, containment, and launch safety considerations.
- Top Cited PapersOpen Access
- 11 December 2019
- Published by Springer Nature in Space Science Reviews
- Vol. 215 (8) , 1-41
European Radioisotope Thermoelectric Generators (RTGs) and Radioisotope Heater Units (RHUs) for Space Science and Exploration
Radioisotope power systems utilising americium-241 as a source of heat have been under development in Europe as part of a European Space Agency funded programme since 2009. The aim is to develop all of the building blocks that would enable Europe to launch and operate deep space and planetary missions in environments where use of solar power or alternative power generation technologies is challenging. Although some technical and policy work activity predate the ESA programme, the maturity of the technology has now reached a level that it can be incorporated in mission studies and roadmaps targeting the period from the mid 2020s onwards. This paper describes the state of the art in European radioisotope thermoelectric generators and radioisotope heater units. This paper includes: the evolution of the technical programme in detail; descriptions of the design; evolution of RTG and RHU devices from laboratory prototypes to more advanced fully functional systems; and experimental data obtained to date. This paper also outlines the technical challenges and multidisciplinary skills required to develop what is a world leading, original, significant and transformative technology solution for planetary science and exploration missions from the mid 2020s onwards.
- 11 December 2019
- Published by Springer Nature in Space Science Reviews
- Vol. 215 (8) , 1-41
Top Cited PapersOpen AccessEuropean Radioisotope Thermoelectric Generators (RTGs) and Radioisotope Heater Units (RHUs) for Space Science and Exploration
Radioisotope power systems utilising americium-241 as a source of heat have been under development in Europe as part of a European Space Agency funded programme since 2009. The aim is to develop all of the building blocks that would enable Europe to launch and operate deep space and planetary missions in environments where use of solar power or alternative power generation technologies is challenging. Although some technical and policy work activity predate the ESA programme, the maturity of the technology has now reached a level that it can be incorporated in mission studies and roadmaps targeting the period from the mid 2020s onwards. This paper describes the state of the art in European radioisotope thermoelectric generators and radioisotope heater units. This paper includes: the evolution of the technical programme in detail; descriptions of the design; evolution of RTG and RHU devices from laboratory prototypes to more advanced fully functional systems; and experimental data obtained to date. This paper also outlines the technical challenges and multidisciplinary skills required to develop what is a world leading, original, significant and transformative technology solution for planetary science and exploration missions from the mid 2020s onwards.
- Open Access
- 1 August 2018
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 507, 158-163
Detailed X-ray diffraction analysis of Ce1-xNdxO2-(x/2) as a surrogate for substoichiometric americium oxide
- 1 August 2018
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 507, 158-163
Open AccessDetailed X-ray diffraction analysis of Ce1-xNdxO2-(x/2) as a surrogate for substoichiometric americium oxide
- Open Access
- 23 May 2017
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 16, 05002
Recent Joint Studies Related to the Development of Space Radioisotope Power Systems
E3S Web of Conferences, open access proceedings in environment, energy and earth sciences
- 23 May 2017
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 16, 05002
Open AccessRecent Joint Studies Related to the Development of Space Radioisotope Power Systems
E3S Web of Conferences, open access proceedings in environment, energy and earth sciences
- 3 February 2004
- Published by SPIE-Intl Soc Optical Eng
- Vol. 5165, 241-251
Swift XRT effective area measured at the Panter end-to-end tests
The Swift X-ray Telescope (XRT) is designed to make astrometric, spectroscopic and photometric observations of the X-ray emission from Gamma-ray bursts and their afterglows, in the energy band 0.2 - 10 keV. Here we report first results of the analysis of Swift XRT effective area at five different energies as measured during the end-to-end calibration campaign at the Panter X-ray beam line facility. The analysis comprises the study of the effective area both on-axis and off-axis for different event grade selection. We compare the laboratory results with the expectations and show that the measured effective area meets the mission scientific requirements.
- 3 February 2004
- Published by SPIE-Intl Soc Optical Eng
- Vol. 5165, 241-251
Swift XRT effective area measured at the Panter end-to-end tests
The Swift X-ray Telescope (XRT) is designed to make astrometric, spectroscopic and photometric observations of the X-ray emission from Gamma-ray bursts and their afterglows, in the energy band 0.2 - 10 keV. Here we report first results of the analysis of Swift XRT effective area at five different energies as measured during the end-to-end calibration campaign at the Panter X-ray beam line facility. The analysis comprises the study of the effective area both on-axis and off-axis for different event grade selection. We compare the laboratory results with the expectations and show that the measured effective area meets the mission scientific requirements.
- Open Access
- 10 March 2003
- Published by SPIE-Intl Soc Optical Eng
- Vol. 4851, 842-848
Proton-induced leakage current in CCDs
The effect of different proton fluences on the performance of two E2V Technologies CCD47-20 devices was investigated with particular emphasis given to the analysis of 'random telegraph signal' (RTS) generation, bright pixel generation and induced changes in base dark current level. The results show that bright pixel frequency increases as the mean energy of the proton beam is increased, and that the base dark current level after irradiation scales with the level of ionization damage. For the RTS study, 500 pixels on one device were monitored over a twelve hour period. This data set revealed a number of distinct types of pixel change level fluctuation and a system of classification has been devised. Previously published RTS data is discussed and reviewed in light of the new data.
- 10 March 2003
- Published by SPIE-Intl Soc Optical Eng
- Vol. 4851, 842-848
Open AccessProton-induced leakage current in CCDs
The effect of different proton fluences on the performance of two E2V Technologies CCD47-20 devices was investigated with particular emphasis given to the analysis of 'random telegraph signal' (RTS) generation, bright pixel generation and induced changes in base dark current level. The results show that bright pixel frequency increases as the mean energy of the proton beam is increased, and that the base dark current level after irradiation scales with the level of ionization damage. For the RTS study, 500 pixels on one device were monitored over a twelve hour period. This data set revealed a number of distinct types of pixel change level fluctuation and a system of classification has been devised. Previously published RTS data is discussed and reviewed in light of the new data.