Raj Kamal Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Raj Kamal Singh has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
Sarathi Ramanujam
7 shared publicationsLigy Philip
5 shared publications- Ligy Philip
Environmental Engineering Division, Department of Civil Engineering, IIT Madras, Chennai 600 036, India
4 shared publications - Hema Priyamvada
EWRE Division, Department of Civil Engineering, Indian Institute of Technology Madras, Chennai, 600036, India.
3 shared publications - Selma Mededovic Thagard
Department of Chemical and Biomolecular Engineering, Clarkson University, Potsdam, USA
3 shared publications - Thomas M. Holsen
Clarkson University
3 shared publications
Latest Publications
- 1 April 2021
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 408, 124452
Treatment of PFAS-containing landfill leachate using an enhanced contact plasma reactor
- 1 April 2021
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 408, 124452
Treatment of PFAS-containing landfill leachate using an enhanced contact plasma reactor
- Top Cited Papers
- 3 September 2019
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 53 (19) , 11375-11382
Rapid Removal of Poly- and Perfluorinated Compounds from Investigation-Derived Waste (IDW) in a Pilot-Scale Plasma Reactor
A pilot-scale plasma reactor installed into an 8 × 20 ft mobile trailer was used to rapidly and effectively degrade poly- and perfluoroalkyl substances (PFAS) from liquid investigation-derived waste (IDW; development and purge water from monitoring wells) obtained from 13 different site investigations at Air Force installations. In the raw water, numerous PFAS were detected in a wide concentration range (~10 to 105 ng/L; total oxidizable precursors (TOP) ~102 to 105 ng/L, total fluorine by combustion ion chromatography (CIC) ~102 to 5×106 ng F/L). The concentration of total PFAS (12 perfluorocarboxylic acids (PFCAs) and perfluoroalkyl sulfonates (PFSAs)) in the 13 samples ranged between 2.7 and 1440 µg/L and the concentration of perfluorooctane sulfonate (PFOS) plus perfluorooctanoic acid (PFOA) ranged between 365 and 73700 ng/L. Plasma-based water treatment resulted in rapid perfluoroalkyl acids (PFAAs) removal from 4 L individual IDW samples with faster rates for longer-chain PFCAs (C ≥ 8) and PFSAs (C ≥ 6) than for PFCAs and PFSAs of shorter chain length. In nine of the 13 IDW samples both PFOS and PFOA were removed to below United States Environmental Protection Agency’s (USEPA’s) health advisory concentration level (HAL) concentrations in < 1 minute whereas longer treatment times (up to 50 minutes) were required for the remaining four IDW samples due to either extremely high solution electrical conductivity which decreased the plasma-liquid contact area (one IDW sample) or high concentrations of PFAAs and their precursors; the latter were found to be converted to PFAAs during the treatment. Overall, 36 to 99% of the TOP concentration present in the IDWs were removed during the treatment. There was no effect of non-PFAS co-contaminants on the degradation efficiency. Overall, the results indicate that plasma-based water treatment is a viable technology for the treatment of PFAS-contaminated IDW.
- 3 September 2019
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 53 (19) , 11375-11382
Top Cited PapersRapid Removal of Poly- and Perfluorinated Compounds from Investigation-Derived Waste (IDW) in a Pilot-Scale Plasma Reactor
A pilot-scale plasma reactor installed into an 8 × 20 ft mobile trailer was used to rapidly and effectively degrade poly- and perfluoroalkyl substances (PFAS) from liquid investigation-derived waste (IDW; development and purge water from monitoring wells) obtained from 13 different site investigations at Air Force installations. In the raw water, numerous PFAS were detected in a wide concentration range (~10 to 105 ng/L; total oxidizable precursors (TOP) ~102 to 105 ng/L, total fluorine by combustion ion chromatography (CIC) ~102 to 5×106 ng F/L). The concentration of total PFAS (12 perfluorocarboxylic acids (PFCAs) and perfluoroalkyl sulfonates (PFSAs)) in the 13 samples ranged between 2.7 and 1440 µg/L and the concentration of perfluorooctane sulfonate (PFOS) plus perfluorooctanoic acid (PFOA) ranged between 365 and 73700 ng/L. Plasma-based water treatment resulted in rapid perfluoroalkyl acids (PFAAs) removal from 4 L individual IDW samples with faster rates for longer-chain PFCAs (C ≥ 8) and PFSAs (C ≥ 6) than for PFCAs and PFSAs of shorter chain length. In nine of the 13 IDW samples both PFOS and PFOA were removed to below United States Environmental Protection Agency’s (USEPA’s) health advisory concentration level (HAL) concentrations in < 1 minute whereas longer treatment times (up to 50 minutes) were required for the remaining four IDW samples due to either extremely high solution electrical conductivity which decreased the plasma-liquid contact area (one IDW sample) or high concentrations of PFAAs and their precursors; the latter were found to be converted to PFAAs during the treatment. Overall, 36 to 99% of the TOP concentration present in the IDWs were removed during the treatment. There was no effect of non-PFAS co-contaminants on the degradation efficiency. Overall, the results indicate that plasma-based water treatment is a viable technology for the treatment of PFAS-contaminated IDW.
- Top Cited Papers
- 15 February 2019
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 53 (5) , 2731-2738
Breakdown Products from Perfluorinated Alkyl Substances (PFAS) Degradation in a Plasma-Based Water Treatment Process
Byproducts produced when treating perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) in water using a plasma treatment process intentionally operated to treat these compounds slowly to allow for byproduct accumulation were quantified. Several linear chain perfluoroalkyl carboxylic acids (PFCAs) (C4 to C7) were identified as byproducts of both PFOA and PFOS treatment. PFOA, perfluorohexane sulfonate (PFHxS) and perfluorobutane sulfonate (PFBS) were also found to be byproducts from PFOS degradation. Significant concentrations of fluoride ions, inorganic carbon and smaller organic acids (trifluoroacetic acid, acetic acid and formic acid) were also identified. In addition to PFCAs, PFHxS and PFBS, trace amounts of 43 PFOA-related and 35 PFOS-related byproducts were also identified using a screening and search-based algorithm. Minor concentrations of gas-phase byproducts were also identified (< 2.5% of the F originally associated with the parent molecules) some of which are reported for the first time in perfluoroalkyl substance degradation experiments including cyclic perfluoroalkanes (C4F8, C5F10, C6F12, C7F14 and C8F16). The short chain PFCAs detected suggest the occurrence of a step-wise reduction of the parent perfluoroalkyl substances (PFAS) molecule, followed by oxidation of intermediates, perfluoroalkyl radicals and perfluoro alcohols/ketones. Using a fluorine mass balance, 77% of the fluorine associated with the parent PFOA and 58% of the fluorine associated with the parent PFOS were identified. The bulk of the remaining fluorine was determined to be sorbed to reactor walls and tubing using sorption experiments in which plasma was not generated.
- 15 February 2019
- Published by American Chemical Society (ACS) in Environmental Science & Technology
- Vol. 53 (5) , 2731-2738
Top Cited PapersBreakdown Products from Perfluorinated Alkyl Substances (PFAS) Degradation in a Plasma-Based Water Treatment Process
Byproducts produced when treating perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) in water using a plasma treatment process intentionally operated to treat these compounds slowly to allow for byproduct accumulation were quantified. Several linear chain perfluoroalkyl carboxylic acids (PFCAs) (C4 to C7) were identified as byproducts of both PFOA and PFOS treatment. PFOA, perfluorohexane sulfonate (PFHxS) and perfluorobutane sulfonate (PFBS) were also found to be byproducts from PFOS degradation. Significant concentrations of fluoride ions, inorganic carbon and smaller organic acids (trifluoroacetic acid, acetic acid and formic acid) were also identified. In addition to PFCAs, PFHxS and PFBS, trace amounts of 43 PFOA-related and 35 PFOS-related byproducts were also identified using a screening and search-based algorithm. Minor concentrations of gas-phase byproducts were also identified (< 2.5% of the F originally associated with the parent molecules) some of which are reported for the first time in perfluoroalkyl substance degradation experiments including cyclic perfluoroalkanes (C4F8, C5F10, C6F12, C7F14 and C8F16). The short chain PFCAs detected suggest the occurrence of a step-wise reduction of the parent perfluoroalkyl substances (PFAS) molecule, followed by oxidation of intermediates, perfluoroalkyl radicals and perfluoro alcohols/ketones. Using a fluorine mass balance, 77% of the fluorine associated with the parent PFOA and 58% of the fluorine associated with the parent PFOS were identified. The bulk of the remaining fluorine was determined to be sorbed to reactor walls and tubing using sorption experiments in which plasma was not generated.
- 1 January 2019
- Published by Elsevier in Chemical Engineering Journal
- Vol. 355, 269-278
Continuous flow pulse corona discharge reactor for the tertiary treatment of drinking water: Insights on disinfection and emerging contaminants removal
- 1 January 2019
- Published by Elsevier in Chemical Engineering Journal
- Vol. 355, 269-278
Continuous flow pulse corona discharge reactor for the tertiary treatment of drinking water: Insights on disinfection and emerging contaminants removal
- 1 June 2018
- Published by Elsevier in Building and Environment
- Vol. 137, 215-225
Assessment of PM and bioaerosols at diverse indoor environments in a southern tropical Indian region
- 1 June 2018
- Published by Elsevier in Building and Environment
- Vol. 137, 215-225
Assessment of PM and bioaerosols at diverse indoor environments in a southern tropical Indian region
- 23 May 2018
- Published by Wiley in Plasma Processes and Polymers
- Vol. 15 (6)
Chemical reaction mechanisms accompanying pulsed electrical discharges in liquid methanol
The primary goal of this study was to explore the fundamental chemical processes occurring during a pulsed electrical discharge in liquid methanol. To this end, advanced analytical techniques were used to identify and, when possible, quantify gas and liquid methanol decomposition products. The effects of applied voltage, voltage polarity, and presence of water on the reaction stoichiometry and the selectivity for the identified gas products were also studied. Density Functional Theory (DFT) simulations were used to determine the most feasible thermal reaction pathways between 300 and 4000 K responsible for the formation of experimentally identified gas and liquid products. From these results, the key chemical reaction pathways were theorized and a reaction mechanism was developed. Gas products of plasma‐induced decomposition of methanol that were detected and quantified include hydrogen, carbon monoxide, carbon dioxide, methane, acetylene, ethylene, and ethane. The reaction selectivity was the highest for the former two compounds regardless of the applied voltage, discharge polarity or presence of water in the starting solution. Results also showed that the applied voltage, discharge polarity and presence of water had no effect on the types of reaction products. Liquid methanol decomposition products that where identified include ethanol, ethylene glycol, formaldehyde, acetic acid, allyl alcohol, 1‐propanol, 3‐buten‐1‐ol, 3‐butyn‐1‐ol, glycolaldehyde, and methyl glycolate. The chemical reaction mechanism that was proposed to explain the formation of the experimentally verified gas products offers specific pathways for the production of carbon monoxide and short‐chained hydrocarbons. In contrast, the reactions leading to the formation of hydrogen, carbon dioxide, and liquid products appear to be random. In general, recombination reactions of direct methanol decomposition products are largely responsible for the formation of C1 and C2 liquid products. Step‐wise reactions of those compounds with single or multiple carbon‐based radicals grow the molecular chain length to up to four carbon atoms thereby producing C4 compounds.
- 23 May 2018
- Published by Wiley in Plasma Processes and Polymers
- Vol. 15 (6)
Chemical reaction mechanisms accompanying pulsed electrical discharges in liquid methanol
The primary goal of this study was to explore the fundamental chemical processes occurring during a pulsed electrical discharge in liquid methanol. To this end, advanced analytical techniques were used to identify and, when possible, quantify gas and liquid methanol decomposition products. The effects of applied voltage, voltage polarity, and presence of water on the reaction stoichiometry and the selectivity for the identified gas products were also studied. Density Functional Theory (DFT) simulations were used to determine the most feasible thermal reaction pathways between 300 and 4000 K responsible for the formation of experimentally identified gas and liquid products. From these results, the key chemical reaction pathways were theorized and a reaction mechanism was developed. Gas products of plasma‐induced decomposition of methanol that were detected and quantified include hydrogen, carbon monoxide, carbon dioxide, methane, acetylene, ethylene, and ethane. The reaction selectivity was the highest for the former two compounds regardless of the applied voltage, discharge polarity or presence of water in the starting solution. Results also showed that the applied voltage, discharge polarity and presence of water had no effect on the types of reaction products. Liquid methanol decomposition products that where identified include ethanol, ethylene glycol, formaldehyde, acetic acid, allyl alcohol, 1‐propanol, 3‐buten‐1‐ol, 3‐butyn‐1‐ol, glycolaldehyde, and methyl glycolate. The chemical reaction mechanism that was proposed to explain the formation of the experimentally verified gas products offers specific pathways for the production of carbon monoxide and short‐chained hydrocarbons. In contrast, the reactions leading to the formation of hydrogen, carbon dioxide, and liquid products appear to be random. In general, recombination reactions of direct methanol decomposition products are largely responsible for the formation of C1 and C2 liquid products. Step‐wise reactions of those compounds with single or multiple carbon‐based radicals grow the molecular chain length to up to four carbon atoms thereby producing C4 compounds.
- 1 February 2018
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 6 (1) , 923-929
Effect of recycling overhead gases on pollutants degradation efficiency in gas-phase pulsed corona discharge treatment
- 1 February 2018
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 6 (1) , 923-929
Effect of recycling overhead gases on pollutants degradation efficiency in gas-phase pulsed corona discharge treatment
- Open Access
- 11 September 2017
- Published by Springer Nature in Scientific Reports
- Vol. 7 (1) , 11171
Seasonal variation of the dominant allergenic fungal aerosols – One year study from southern Indian region
Quantitative estimations of fungal aerosols are important to understand their role in causing respiratory diseases to humans especially in the developing and highly populated countries. In this study we sampled and quantified the three most dominantly found allergenic airborne fungi, Aspergillus fumigatus, Cladosporium cladosporioides, and Alternaria alternata from ambient PM10 samples using the quantitative PCR (qPCR) technique in a southern tropical Indian region, for one full year. Highest concentrations of A. fumigatus and C. cladosporioides were observed during monsoon whereas A. alternata displayed an elevated concentration in winter. The meteorological parameters such as temperature, relative humidity, wind speed, and precipitation exhibited a substantial influence on the atmospheric concentrations of allergenic fungal aerosols. The morphological features of various allergenic fungal spores present in the PM10 were investigated and the spores were found to possess distinct structural features. In a maiden attempt over this region we correlate the ambient fungal concentrations with the epidemiological allergy occurrence to obtain firsthand and preliminary information about the causative fungal allergen to the inhabitants exposed to bioaerosols. Our findings may serve as an important reference to atmospheric scientists, aero-biologists, doctors, and general public.
- 11 September 2017
- Published by Springer Nature in Scientific Reports
- Vol. 7 (1) , 11171
Open AccessSeasonal variation of the dominant allergenic fungal aerosols – One year study from southern Indian region
Quantitative estimations of fungal aerosols are important to understand their role in causing respiratory diseases to humans especially in the developing and highly populated countries. In this study we sampled and quantified the three most dominantly found allergenic airborne fungi, Aspergillus fumigatus, Cladosporium cladosporioides, and Alternaria alternata from ambient PM10 samples using the quantitative PCR (qPCR) technique in a southern tropical Indian region, for one full year. Highest concentrations of A. fumigatus and C. cladosporioides were observed during monsoon whereas A. alternata displayed an elevated concentration in winter. The meteorological parameters such as temperature, relative humidity, wind speed, and precipitation exhibited a substantial influence on the atmospheric concentrations of allergenic fungal aerosols. The morphological features of various allergenic fungal spores present in the PM10 were investigated and the spores were found to possess distinct structural features. In a maiden attempt over this region we correlate the ambient fungal concentrations with the epidemiological allergy occurrence to obtain firsthand and preliminary information about the causative fungal allergen to the inhabitants exposed to bioaerosols. Our findings may serve as an important reference to atmospheric scientists, aero-biologists, doctors, and general public.
- 1 September 2017
- Published by Elsevier in Water Research
- Vol. 121, 20-36
Rapid degradation, mineralization and detoxification of pharmaceutically active compounds in aqueous solution during pulsed corona discharge treatment
- 1 September 2017
- Published by Elsevier in Water Research
- Vol. 121, 20-36
Rapid degradation, mineralization and detoxification of pharmaceutically active compounds in aqueous solution during pulsed corona discharge treatment