Aiping Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aiping Zhang has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Zhepei Gu
School of Environmental Science and Engineering Southwest Jiaotong University Chengdu China
8 shared publications Qibin Li
Faculty of Geosciences and Environmental Engineering, Southwest Jiaotong University, Chengdu 611756, China
5 shared publicationsWeiming Chen
Faculty of Geosciences and Environmental Engineering, Southwest Jiaotong University, Chengdu 611756, China
5 shared publicationsJia Tang
College of Chemistry and Materials Science, Sichuan Normal University, Chengdu, China
4 shared publicationsSiping Yang
College of Chemistry and Materials Science, Sichuan Normal University, Chengdu, China
4 shared publicationsXiaoqin Zhang
College of Chemistry and Materials Science, Sichuan Normal University, Chengdu, China
4 shared publications
Latest Publications
- Open Access
- 4 June 2025
- Published by HARD Publishing Company in Polish Journal of Environmental Studies
- Vol. 35 (3) , 3055-3067
Effect of Freeze-Thaw Cyclic Aging on the Adsorption Performance of Sheep Manure Biochar
Biochar, SMB, was prepared from waste sheep manure and aged under simulated freeze-thaw cyclic conditions, and the effects of freeze-thaw cyclic aging on the performance and behavioral features of SMB when adsorbing methylene blue (MB) dye in water and its influence mechanism were investigated. The results showed that 7~42 cycles of freeze-thaw aging could effectively improve the pore structure of SMB and enhance its adsorption performance. After 14 freeze-thaw cycles, SMB could remove 95.7% of MB under the optimal operating conditions, and the adsorption amount of MB reached 143.5 mg/g, which was 14% higher than that of unaged SMB. When the freeze-thaw cycles reached 49, the pore structure of SMB was damaged, and its adsorption performance deteriorated, and the adsorption amount of MB was 18.8% lower than that before aging. The adsorption behaviors of SMB on MB both before and after freeze-thaw cyclic aging were chemically dominated, multilayered, entropy-driven, spontaneous, and heat-absorbing. Freeze-thaw cyclic aging increased the chemical dominance and spontaneity of adsorption in the shorter term, while decreasing them in the longer term. The adsorption mechanisms all involved electrostatic attraction, pore filling, hydrogen bonding, and π-π bonding interaction, with pore filling being enhanced after shorter-term freeze-thaw cyclic aging. The findings provide broader theoretical support for the application and promotion of SMB in actual pollution management.
- 4 June 2025
- Published by HARD Publishing Company in Polish Journal of Environmental Studies
- Vol. 35 (3) , 3055-3067
Open AccessEffect of Freeze-Thaw Cyclic Aging on the Adsorption Performance of Sheep Manure Biochar
Biochar, SMB, was prepared from waste sheep manure and aged under simulated freeze-thaw cyclic conditions, and the effects of freeze-thaw cyclic aging on the performance and behavioral features of SMB when adsorbing methylene blue (MB) dye in water and its influence mechanism were investigated. The results showed that 7~42 cycles of freeze-thaw aging could effectively improve the pore structure of SMB and enhance its adsorption performance. After 14 freeze-thaw cycles, SMB could remove 95.7% of MB under the optimal operating conditions, and the adsorption amount of MB reached 143.5 mg/g, which was 14% higher than that of unaged SMB. When the freeze-thaw cycles reached 49, the pore structure of SMB was damaged, and its adsorption performance deteriorated, and the adsorption amount of MB was 18.8% lower than that before aging. The adsorption behaviors of SMB on MB both before and after freeze-thaw cyclic aging were chemically dominated, multilayered, entropy-driven, spontaneous, and heat-absorbing. Freeze-thaw cyclic aging increased the chemical dominance and spontaneity of adsorption in the shorter term, while decreasing them in the longer term. The adsorption mechanisms all involved electrostatic attraction, pore filling, hydrogen bonding, and π-π bonding interaction, with pore filling being enhanced after shorter-term freeze-thaw cyclic aging. The findings provide broader theoretical support for the application and promotion of SMB in actual pollution management.
- 15 February 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (17) , 50295-50308
Degradation of refractory organic matter in MBR effluent from treating landfill leachate by the UV-nZVI-H2O2 system
In this study, nano zero-valent iron (nZVI) was used as the Fe2+ source in the Fenton reaction, and a UV-nZVI-H2O2 system was constructed to efficiently degrade and mineralize refractory organic matter in landfill leachate. The results showed that under the optimal conditions (initial pH = 3, UV = 14 W, nZVI = 0.5 g/L, and [H2O2] = 30 mM), the removal efficiencies of total organic carbon, absorbance at 254 nm, and color number were 61.38%, 83.89%, and 85.79%, respectively. Control experiments show that the UV-nZVI-H2O2 system has the highest removal rate and mineralization rate of refractory organic matter. The excellent performance of the UV-nZVI-H2O2 system is related to a higher H2O2 utilization rate. The H2O2 residue in the UV-nZVI-H2O2 system was the lowest, and the effective utilization rate of H2O2 was as high as 98.80%. Alcohol quenching experiments and hydroxyl radical quantitative experiments showed that the dominant reactive oxygen species in the UV-nZVI-H2O2 system was HO• and the yield of HO• was as high as 2007.80 μM, which was much higher than that in other systems. The results of spectra analysis showed that the low molecular weight, high fluorescence frequency organic matter, and relatively stable aromatic organic matter were significantly degraded after treatment with the UV-nZVI-H2O2 system and the aromatic degree, humification degree, molecular weight, and molecular polymerization degree of refractory organic matter were also significantly decreased. The mechanism of the UV-nZVI-H2O2 reaction includes homogeneous and heterogeneous Fenton reactions and adsorption and precipitation of organic matter by iron-based colloids. This study can provide theoretical and technical support for the advanced treatment of refractory organic matter in landfill leachate.
- 15 February 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (17) , 50295-50308
Degradation of refractory organic matter in MBR effluent from treating landfill leachate by the UV-nZVI-H2O2 system
In this study, nano zero-valent iron (nZVI) was used as the Fe2+ source in the Fenton reaction, and a UV-nZVI-H2O2 system was constructed to efficiently degrade and mineralize refractory organic matter in landfill leachate. The results showed that under the optimal conditions (initial pH = 3, UV = 14 W, nZVI = 0.5 g/L, and [H2O2] = 30 mM), the removal efficiencies of total organic carbon, absorbance at 254 nm, and color number were 61.38%, 83.89%, and 85.79%, respectively. Control experiments show that the UV-nZVI-H2O2 system has the highest removal rate and mineralization rate of refractory organic matter. The excellent performance of the UV-nZVI-H2O2 system is related to a higher H2O2 utilization rate. The H2O2 residue in the UV-nZVI-H2O2 system was the lowest, and the effective utilization rate of H2O2 was as high as 98.80%. Alcohol quenching experiments and hydroxyl radical quantitative experiments showed that the dominant reactive oxygen species in the UV-nZVI-H2O2 system was HO• and the yield of HO• was as high as 2007.80 μM, which was much higher than that in other systems. The results of spectra analysis showed that the low molecular weight, high fluorescence frequency organic matter, and relatively stable aromatic organic matter were significantly degraded after treatment with the UV-nZVI-H2O2 system and the aromatic degree, humification degree, molecular weight, and molecular polymerization degree of refractory organic matter were also significantly decreased. The mechanism of the UV-nZVI-H2O2 reaction includes homogeneous and heterogeneous Fenton reactions and adsorption and precipitation of organic matter by iron-based colloids. This study can provide theoretical and technical support for the advanced treatment of refractory organic matter in landfill leachate.
- 18 January 2023
- Published by Taylor & Francis in Environmental Technology
- Vol. 45 (7) , 1313-1325
Degradation of refractory organic matter in MBR effluent from treating landfill leachate by UV/PMS and UV/H 2 O 2 : a comparative study
This study applied ultraviolet/peroxymonosulfate (UV/PMS) and UV/hydrogen peroxide (UV/H2O2) processes to the advanced treatment of membrane bioreactor (MBR) effluent. The degradation efficiency of refractory organic matter and the reaction mechanisms of the two processes were systematically investigated. The results showed that the degradation efficiency of the UV/PMS processes was significantly lower than that of the UV/H2O2 process when the PMS concentration was significantly lower than the H2O2 concentration, e.g., the UV254 removals under optimal conditions were 72.92% and 82.21%, respectively. Additionally, the UV/PMS process could operate over a broader pH range. The degradation efficiency of the UV/PMS process was slightly increased by HCO3- and Cl- due to the activation of PMS, while in the UV/H2O2 process, HCO3- and Cl- depressed the degradation efficiency by competing with organic matter to react with reactive oxygen species (ROS). After the two processes, the aromaticity, humification, condensation degree, and molecular weight of refractory organic matter in the MBR effluent were considerably decreased. Fulvic- (HA) and humic-like substances (FA) were greatly degraded by the two processes. The UV/PMS had a superior degradation efficiency for macromolecular HA in the early stage of the reaction, and the UV/H2O2 could degrade HA to protein-like substances in the latter stage of the reaction. These differences between the two processes could be attributed to the dominance of different ROS, with SO4•- and HO• dominating in the UV/PMS, and HO• dominating in the UV/H2O2. The results of this study provide theoretical support for the application of MBR effluent treatment. GRAPHICAL ABSTRACT
- 18 January 2023
- Published by Taylor & Francis in Environmental Technology
- Vol. 45 (7) , 1313-1325
Degradation of refractory organic matter in MBR effluent from treating landfill leachate by UV/PMS and UV/H 2 O 2 : a comparative study
This study applied ultraviolet/peroxymonosulfate (UV/PMS) and UV/hydrogen peroxide (UV/H2O2) processes to the advanced treatment of membrane bioreactor (MBR) effluent. The degradation efficiency of refractory organic matter and the reaction mechanisms of the two processes were systematically investigated. The results showed that the degradation efficiency of the UV/PMS processes was significantly lower than that of the UV/H2O2 process when the PMS concentration was significantly lower than the H2O2 concentration, e.g., the UV254 removals under optimal conditions were 72.92% and 82.21%, respectively. Additionally, the UV/PMS process could operate over a broader pH range. The degradation efficiency of the UV/PMS process was slightly increased by HCO3- and Cl- due to the activation of PMS, while in the UV/H2O2 process, HCO3- and Cl- depressed the degradation efficiency by competing with organic matter to react with reactive oxygen species (ROS). After the two processes, the aromaticity, humification, condensation degree, and molecular weight of refractory organic matter in the MBR effluent were considerably decreased. Fulvic- (HA) and humic-like substances (FA) were greatly degraded by the two processes. The UV/PMS had a superior degradation efficiency for macromolecular HA in the early stage of the reaction, and the UV/H2O2 could degrade HA to protein-like substances in the latter stage of the reaction. These differences between the two processes could be attributed to the dominance of different ROS, with SO4•- and HO• dominating in the UV/PMS, and HO• dominating in the UV/H2O2. The results of this study provide theoretical support for the application of MBR effluent treatment. GRAPHICAL ABSTRACT
- 6 August 2022
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 10 (5) , 108391
Removal efficiency and mechanism of refractory organic matter from landfill leachate MBR effluent by the MoS2-enhanced Fe0/H2O2 system
- 6 August 2022
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 10 (5) , 108391
Removal efficiency and mechanism of refractory organic matter from landfill leachate MBR effluent by the MoS2-enhanced Fe0/H2O2 system
- 4 April 2022
- Published by Elsevier in Process Safety and Environmental Protection
- Vol. 162, 955-964
A comparative study of the degradation of refractory organic matter in MBR effluent from landfill leachate treatment by the microwave-enhanced iron-activated hydrogen peroxide and peroxydisulfate processes
- 4 April 2022
- Published by Elsevier in Process Safety and Environmental Protection
- Vol. 162, 955-964
A comparative study of the degradation of refractory organic matter in MBR effluent from landfill leachate treatment by the microwave-enhanced iron-activated hydrogen peroxide and peroxydisulfate processes
- 13 July 2020
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 27 (32) , 40219-40228
Degradation of recalcitrant organic matter in SAARB leachate by a combined process of coagulation and catalytic ozonation
A combined coagulation and γ-Al2O3 catalytic ozonation process was used to treat semi-aerobic aged refuse biofilter (SAARB) effluent from treating mature landfill leachate. First, the coagulant providing the best pretreatment performance was selected. Then, the coagulated SAARB leachate was further treated in an optimized γ-Al2O3-catalyzed ozonation process. Characteristics of the γ-Al2O3-catalyzed ozonation process were determined, and a reaction mechanism was proposed. FeCl3 provided the best treatment efficiency (chemical oxygen demand (COD) removal of 65.8%, absorbance at 254 nm (UV254) removal of 68.55%, and color number (CN) removal of 79.4%). Under optimized O3 dosage (18.92 mg/min) and γ-Al2O3 dosage (10 g/L), efficiencies of removing COD, UV254, and CN were 54.3%, 82.9%, and 95.9%, respectively, at 30 min. In addition, spectral analysis indicated that fulvic-like substances in ultraviolet and visible regions were effectively degraded in the γ-Al2O3-O3 process and some smaller organic products were produced. Characterization of γ-Al2O3 showed that γ-Al2O3 was relative stable; its morphology and constituent elements did not change much after reaction. In addition, ozonation capacity was enhanced by heterogeneous catalytic effects of γ-Al2O3. The combined coagulation and γ-Al2O3 catalytic ozonation process was proven to be an efficient treatment method for removing bio-refractory organic matter contained in SAARB leachate.
- 13 July 2020
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 27 (32) , 40219-40228
Degradation of recalcitrant organic matter in SAARB leachate by a combined process of coagulation and catalytic ozonation
A combined coagulation and γ-Al2O3 catalytic ozonation process was used to treat semi-aerobic aged refuse biofilter (SAARB) effluent from treating mature landfill leachate. First, the coagulant providing the best pretreatment performance was selected. Then, the coagulated SAARB leachate was further treated in an optimized γ-Al2O3-catalyzed ozonation process. Characteristics of the γ-Al2O3-catalyzed ozonation process were determined, and a reaction mechanism was proposed. FeCl3 provided the best treatment efficiency (chemical oxygen demand (COD) removal of 65.8%, absorbance at 254 nm (UV254) removal of 68.55%, and color number (CN) removal of 79.4%). Under optimized O3 dosage (18.92 mg/min) and γ-Al2O3 dosage (10 g/L), efficiencies of removing COD, UV254, and CN were 54.3%, 82.9%, and 95.9%, respectively, at 30 min. In addition, spectral analysis indicated that fulvic-like substances in ultraviolet and visible regions were effectively degraded in the γ-Al2O3-O3 process and some smaller organic products were produced. Characterization of γ-Al2O3 showed that γ-Al2O3 was relative stable; its morphology and constituent elements did not change much after reaction. In addition, ozonation capacity was enhanced by heterogeneous catalytic effects of γ-Al2O3. The combined coagulation and γ-Al2O3 catalytic ozonation process was proven to be an efficient treatment method for removing bio-refractory organic matter contained in SAARB leachate.
- 1 March 2020
- Published by Elsevier in Chemosphere
- Vol. 242, 125139
Comparison study on microwave irradiation-activated persulfate and hydrogen peroxide systems in the treatment of dinitrodiazophenol industrial wastewater
- 1 March 2020
- Published by Elsevier in Chemosphere
- Vol. 242, 125139
Comparison study on microwave irradiation-activated persulfate and hydrogen peroxide systems in the treatment of dinitrodiazophenol industrial wastewater
- 8 November 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 26 (35) , 35797-35806
Improved oxidation of refractory organics in concentrated leachate by a Fe2+-enhanced O3/H2O2 process
Concentrated leachate from membrane processes, which contains a mass of refractory organics and salt, has become a new problem for wastewater engineers. In this study, removal of organic contaminants in concentrated landfill leachate was investigated by applying the ferrous ion (Fe2+) catalyzed O3/H2O2 process. The maximum chemical oxygen demand (COD) and absorbance at 254 nm (UV254) removal efficiencies under the optimal conditions (initial pH = 3.0, Fe2+ dosage = 6.500 mM, H2O2 dosage = 18.8 mM and O3 dosage = 52.65 mg min−1) were 48.82% and 63.59%, respectively. These were higher than those achieved using the Fe2+/O3, O3/H2O2, and O3 processes, and biodegradability of the leachate was improved significantly. Moreover, compared with other processes, the Fe2+ had a stronger catalytic effect. Molecular distribution analysis and three-dimensional excitation and emission matrix analysis both indicated that the fulvic acid and humic acid in the concentrated leachate were greatly degraded. Ultraviolet-visible spectra showed that the Fe2+/O3/H2O2 process mainly destroyed unsaturated bonds and decreased the aromatic degree of the leachate. The reaction mechanism of the Fe2+/O3/H2O2 process mainly was attributed to three factors: (1) O3 and H2O2 reacting to produce •OH; (2) H2O2 and O3 decomposing into •OH through the oxidation of Fe2+ to Fe3+; and (3) coagulation by Fe (OH)3. The •OH can rapidly degrade recalcitrant organics, and coagulation also increases the removal of organic matter. Therefore, the Fe2+/O3/H2O2 process was an effective method for treating concentrated landfill leachate.
- 8 November 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 26 (35) , 35797-35806
Improved oxidation of refractory organics in concentrated leachate by a Fe2+-enhanced O3/H2O2 process
Concentrated leachate from membrane processes, which contains a mass of refractory organics and salt, has become a new problem for wastewater engineers. In this study, removal of organic contaminants in concentrated landfill leachate was investigated by applying the ferrous ion (Fe2+) catalyzed O3/H2O2 process. The maximum chemical oxygen demand (COD) and absorbance at 254 nm (UV254) removal efficiencies under the optimal conditions (initial pH = 3.0, Fe2+ dosage = 6.500 mM, H2O2 dosage = 18.8 mM and O3 dosage = 52.65 mg min−1) were 48.82% and 63.59%, respectively. These were higher than those achieved using the Fe2+/O3, O3/H2O2, and O3 processes, and biodegradability of the leachate was improved significantly. Moreover, compared with other processes, the Fe2+ had a stronger catalytic effect. Molecular distribution analysis and three-dimensional excitation and emission matrix analysis both indicated that the fulvic acid and humic acid in the concentrated leachate were greatly degraded. Ultraviolet-visible spectra showed that the Fe2+/O3/H2O2 process mainly destroyed unsaturated bonds and decreased the aromatic degree of the leachate. The reaction mechanism of the Fe2+/O3/H2O2 process mainly was attributed to three factors: (1) O3 and H2O2 reacting to produce •OH; (2) H2O2 and O3 decomposing into •OH through the oxidation of Fe2+ to Fe3+; and (3) coagulation by Fe (OH)3. The •OH can rapidly degrade recalcitrant organics, and coagulation also increases the removal of organic matter. Therefore, the Fe2+/O3/H2O2 process was an effective method for treating concentrated landfill leachate.
- 4 November 2019
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Water Research & Technology
- Vol. 6 (3) , 581-592
Activation of persulfate by microwave radiation combined with FeS for treatment of wastewater from explosives production
A persulfate (PS) process activated by microwave (MW) radiation and combined with FeS (MW–FeS/PS) was developed to treat wastewater from explosives production containing dinitrodiazophenol (DDNP). The treatment efficacy and degradation characteristics of refractory organics in the wastewater and the improvement in biodegradability were studied. The catalytic capacity of FeS was determined and the electrical energy consumption of the MW–FeS/PS process was evaluated. The MW–FeS/PS process exhibited a more rapid reaction rate (0.208 mg L−1 min−1) and a higher chemical oxygen demand reduction (76.16%) compared to other controlled processes under the optimized conditions of initial pH = 3.0, PS dosage = 6 g L−1, FeS dosage = 0.4 g L−1, MW power = 450 W, and reaction time = 16 min. Additionally, biodegradability was greatly improved from an initial value of 0.040 for raw wastewater to 0.487 for treated wastewater. Spectral analysis indicated that benzene-ring substances, nitro group substances, and diazo group substances in the wastewater from explosives production containing DDNP were considerably degraded by the MW–FeS/PS process. After several operation cycles, FeS maintained high catalytic capacity. After reaction, the used FeS showed a larger specific surface area and adsorption aperture, and stronger magnetism, which enhanced the treatment efficiency of the MW–FeS/PS process and facilitated separation of the catalyst from the wastewater. Radical quenching experiments showed that sulfate radicals and hydroxyl radicals both considerably contributed to organics degradation in the MW–FeS/PS process. In addition, the MW–FeS/PS process consumed less energy than other processes and achieved higher treatment efficacy, confirming that the MW–FeS/PS process is a highly efficient method for treating wastewater from explosives production.
- 4 November 2019
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Water Research & Technology
- Vol. 6 (3) , 581-592
Activation of persulfate by microwave radiation combined with FeS for treatment of wastewater from explosives production
A persulfate (PS) process activated by microwave (MW) radiation and combined with FeS (MW–FeS/PS) was developed to treat wastewater from explosives production containing dinitrodiazophenol (DDNP). The treatment efficacy and degradation characteristics of refractory organics in the wastewater and the improvement in biodegradability were studied. The catalytic capacity of FeS was determined and the electrical energy consumption of the MW–FeS/PS process was evaluated. The MW–FeS/PS process exhibited a more rapid reaction rate (0.208 mg L−1 min−1) and a higher chemical oxygen demand reduction (76.16%) compared to other controlled processes under the optimized conditions of initial pH = 3.0, PS dosage = 6 g L−1, FeS dosage = 0.4 g L−1, MW power = 450 W, and reaction time = 16 min. Additionally, biodegradability was greatly improved from an initial value of 0.040 for raw wastewater to 0.487 for treated wastewater. Spectral analysis indicated that benzene-ring substances, nitro group substances, and diazo group substances in the wastewater from explosives production containing DDNP were considerably degraded by the MW–FeS/PS process. After several operation cycles, FeS maintained high catalytic capacity. After reaction, the used FeS showed a larger specific surface area and adsorption aperture, and stronger magnetism, which enhanced the treatment efficiency of the MW–FeS/PS process and facilitated separation of the catalyst from the wastewater. Radical quenching experiments showed that sulfate radicals and hydroxyl radicals both considerably contributed to organics degradation in the MW–FeS/PS process. In addition, the MW–FeS/PS process consumed less energy than other processes and achieved higher treatment efficacy, confirming that the MW–FeS/PS process is a highly efficient method for treating wastewater from explosives production.
- 14 September 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 26 (31) , 32666-32671
Dinitrodiazophenol industrial wastewater treatment by a sequential ozone Fenton process
The ozonation process is efficient in degrading aromatic substances and substances with unsaturated bonds, but cannot effectively destroy small-molecule organic compounds, which accumulate. Likewise, the Fenton process is a classic wastewater treatment method, but requires strict pH control and produces secondary pollution when the concentration of organic substances is high. In this study, we applied a 1stO3-2ndFenton sequential process to treat diazodinitrophenol (DDNP) industrial wastewater and provide suitable reaction conditions for Fenton process. For the 1stOzone process, organics removal increased as O3 dosage increased. At optimized operation, the 1stO3 process provided an acidic effluent (pH = 3) and reduced the organics concentration to a level suitable for the 2ndFenton process. Benzene ring substances as well as nitro group and diazo group compounds were greatly degraded in the 1stO3 process and were further mineralized in the 2ndFenton process. Additionally, the biodegradability of DDNP industrial wastewater was greatly improved. This is the first reported time that ozonation and the Fenton process have been integrated sequentially to treat an explosive production wastewater. The study provides a feasible chemical oxidation method for treating DDNP industrial wastewater by simply combining two classic treatment processes.
- 14 September 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 26 (31) , 32666-32671
Dinitrodiazophenol industrial wastewater treatment by a sequential ozone Fenton process
The ozonation process is efficient in degrading aromatic substances and substances with unsaturated bonds, but cannot effectively destroy small-molecule organic compounds, which accumulate. Likewise, the Fenton process is a classic wastewater treatment method, but requires strict pH control and produces secondary pollution when the concentration of organic substances is high. In this study, we applied a 1stO3-2ndFenton sequential process to treat diazodinitrophenol (DDNP) industrial wastewater and provide suitable reaction conditions for Fenton process. For the 1stOzone process, organics removal increased as O3 dosage increased. At optimized operation, the 1stO3 process provided an acidic effluent (pH = 3) and reduced the organics concentration to a level suitable for the 2ndFenton process. Benzene ring substances as well as nitro group and diazo group compounds were greatly degraded in the 1stO3 process and were further mineralized in the 2ndFenton process. Additionally, the biodegradability of DDNP industrial wastewater was greatly improved. This is the first reported time that ozonation and the Fenton process have been integrated sequentially to treat an explosive production wastewater. The study provides a feasible chemical oxidation method for treating DDNP industrial wastewater by simply combining two classic treatment processes.