Mengfei Xiong
Research Subjects
Research Interests
Mengfei Xiong has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Binzhen Zhang
Key Laboratory of Instrumentation Science & Dynamic Measurement, Ministry of Education, North University of China, Taiyuan 030051, China
2 shared publications - Hongcheng Xu
School of Instrument Science and Technology Xi'an Jiaotong University Xi'an P. R. China
2 shared publications - Junping Duan
State Key Laboratory of Extreme Environment Optoelectronic Dynamic Testing Technology and Instrument, North University of China, Taiyuan 030051, China
2 shared publications Binzhen Zhang
1 shared publication- Jianli Cui
Science and Technology on Electronic Test & Measurement Laboratory, Taiyuan China
1 shared publication Junping Duan
1 shared publication
Latest Publications
- Open Access
- 23 April 2020
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2020, 1-11
A Band-Rejection Vivaldi Antenna with High Selectivity Using Hybrid HRW/CCLL
A simplified notched design method for the Vivaldi antenna is exhibiting high frequency-band-selectivity characteristics. By suitably introducing half-wavelength resonator (HWR) and complementary capacitively loaded loop (CCLL), the notched-band selectivity is promoted while maintaining the wide impedance bandwidth of the antenna applicable for wireless communications. HWR is bent in the middle to focus the first notch pole, and the second notch pole is obtained by CCLL on the radiating patch. Additionally, the resonant frequency of the notched pole can be determined by the position and size of two loaded resonators in theoretical analysis, thereby realizing a wideband antenna with the desired notched band. Finally, the Vivaldi antenna of loading resonator was fabricated to verify the feasibility of this new method. Measured and simulated experimental results reveal that the antenna exhibits directional pattern in the passband, low gain at the band-rejection, and excellent selectivity within a frequency range. The simulation and measurement results are in good agreement. The proposed antenna achieves S11<−10 dB in 2.6–13.7 GHz and a notch band from 4.49 to 6.64 GHz to reject IEEE 802.11a and HIPERLAN/2 frequency band. Moreover, the proposed antenna has good frequency selectivity, and its gain is good enough in the passband with peak gain up to 10.8 dBi. This antenna design presents frequency suitability, demonstrating that a UWB antenna with a controllable notched band has been realized.
- 23 April 2020
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2020, 1-11
Open AccessA Band-Rejection Vivaldi Antenna with High Selectivity Using Hybrid HRW/CCLL
A simplified notched design method for the Vivaldi antenna is exhibiting high frequency-band-selectivity characteristics. By suitably introducing half-wavelength resonator (HWR) and complementary capacitively loaded loop (CCLL), the notched-band selectivity is promoted while maintaining the wide impedance bandwidth of the antenna applicable for wireless communications. HWR is bent in the middle to focus the first notch pole, and the second notch pole is obtained by CCLL on the radiating patch. Additionally, the resonant frequency of the notched pole can be determined by the position and size of two loaded resonators in theoretical analysis, thereby realizing a wideband antenna with the desired notched band. Finally, the Vivaldi antenna of loading resonator was fabricated to verify the feasibility of this new method. Measured and simulated experimental results reveal that the antenna exhibits directional pattern in the passband, low gain at the band-rejection, and excellent selectivity within a frequency range. The simulation and measurement results are in good agreement. The proposed antenna achieves S11<−10 dB in 2.6–13.7 GHz and a notch band from 4.49 to 6.64 GHz to reject IEEE 802.11a and HIPERLAN/2 frequency band. Moreover, the proposed antenna has good frequency selectivity, and its gain is good enough in the passband with peak gain up to 10.8 dBi. This antenna design presents frequency suitability, demonstrating that a UWB antenna with a controllable notched band has been realized.
- Open Access
- 1 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 157027-157036
Omnidirectional Solid Angle Beam-Switching Flexible Array Antenna in Millimeter Wave for 5G Micro Base Station Applications
- 1 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 157027-157036
Open AccessOmnidirectional Solid Angle Beam-Switching Flexible Array Antenna in Millimeter Wave for 5G Micro Base Station Applications
- 4 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 17 (12) , 2304-2308
Wide Solid Angle Beam-Switching Conical Conformal Array Antenna With High Gain for 5G Applications
This paper presents the design for three-dimensional polymeride (3D) printing and printed circuit board (PCB) fabrication, and full experimental verification of a conical conformal array antenna with wide solid angle switching beam by a radio-frequency (RF) semiconductor switch (RFSS) configuration. The conical conformal array antenna (CCAA) consists of eight linear array antennas with uniform circumferential arrangement around the conical surface. Only one linear array antenna (LAA) out of eight arrays is individual excited operating each time by the RF semiconductor switch connected the ports of the 1 to 8 power dividers in order to achieve the requirement of beam-switching. The conical conformal array antenna with beam-switching feeding network operates at 4.8 GHz according to the fifth-generation (5G) band requirements. Both the wide solid scanning angle of 0-218° in H-plane and the halfpower bandwidth (HPBW) with that lower than 16° in E-plane are achieved. When the realized gain of each linear array antenna is over 10 dBi, the measured peak gain of the final antenna can reach about over 11 dBi and the average radiation efficiency can reach 59.5%. This conical conformal array antenna with wide solid angle beam-switching and the high gain property has potential for reducing the signal-to-noise ratio and integration with 5G communication systems.
- 4 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 17 (12) , 2304-2308
Wide Solid Angle Beam-Switching Conical Conformal Array Antenna With High Gain for 5G Applications
This paper presents the design for three-dimensional polymeride (3D) printing and printed circuit board (PCB) fabrication, and full experimental verification of a conical conformal array antenna with wide solid angle switching beam by a radio-frequency (RF) semiconductor switch (RFSS) configuration. The conical conformal array antenna (CCAA) consists of eight linear array antennas with uniform circumferential arrangement around the conical surface. Only one linear array antenna (LAA) out of eight arrays is individual excited operating each time by the RF semiconductor switch connected the ports of the 1 to 8 power dividers in order to achieve the requirement of beam-switching. The conical conformal array antenna with beam-switching feeding network operates at 4.8 GHz according to the fifth-generation (5G) band requirements. Both the wide solid scanning angle of 0-218° in H-plane and the halfpower bandwidth (HPBW) with that lower than 16° in E-plane are achieved. When the realized gain of each linear array antenna is over 10 dBi, the measured peak gain of the final antenna can reach about over 11 dBi and the average radiation efficiency can reach 59.5%. This conical conformal array antenna with wide solid angle beam-switching and the high gain property has potential for reducing the signal-to-noise ratio and integration with 5G communication systems.