Furkan H. Isikgor
Research Subjects
Furkan H. Isikgor has a total of 236 co-authors. Here are the top co-authors by number of shared publications:
- Stefaan De Wolf
King Abdullah University of Science and Technology (KAUST)
10 shared publications - Thomas D. Anthopoulos
Henry Royce Institute Photon Science Institute Department of Electrical and Electronic Engineering The University of Manchester Manchester UK
7 shared publications - Erkan Aydin
Department of Chemistry and Center for NanoScience (CeNS) Ludwig‐Maximilians‐Universität (LMU) Munich Germany
4 shared publications Michele De Bastiani
Center for Renewable Energy and Storage Technologies (CREST), Physical Sciences and Engineering Division (PSE)
4 shared publications- Randi Azmi
School of Science and Engineering, The Chinese University of Hong Kong (Shenzhen), Shenzhen, People’s Republic of China
4 shared publications - Derya Baran
King Abdullah University of Science and Technology (KAUST)
3 shared publications
Latest Publications
- Open Access
- 9 October 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Ultra-lightweight Flexible Perovskite–Perovskite–Organic Triple-Junction Tandem Solar Cells
Triple-junction photovoltaics offer a promising route to surpass the efficiency limitations of single-junction solar cells, yet existing high-performance architectures are predominantly rigid and relatively heavy, limiting their use in weight-sensitive applications. Here, we report, to the best of our knowledge, the first ultra-lightweight and flexible monolithic perovskiteperovskite–organic triple-junction tandem solar cells. The devices integrate 2.05 eV and 1.62 eV perovskite front and middle subcells with a 1.33 eV organic bulk-heterojunction rear subcell on a 10 μm flexible polyethylene terephthalate substrate. The champion tandem device achieves a power conversion efficiency of 24.1%, with an open-circuit voltage of 3.27 V, a short-circuit current density of 9.32 mA/cm2, and a fill factor of 79.0%, corresponding to a power-per-weight of 11.2 W/g. The device exhibits a stabilized PCE of 24.6% under maximumpower-point tracking and negligible hysteresis between forward and reverse voltage scans. External quantum efficiency measurements yield closely matched integrated photocurrent densities of 9.39, 9.39, and 9.21 mA/cm2 for the three subcells, confirming efficient spectral utilization and current matching. These results establish flexible perovskite–perovskiteorganic triple-junction tandems as a promising platform for high-specific-power photovoltaics and open opportunities for lightweight energy harvesting in aerospace, unmanned aerial vehicles, wearable electronics, and portable power systems.
- 9 October 2026
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessUltra-lightweight Flexible Perovskite–Perovskite–Organic Triple-Junction Tandem Solar Cells
Triple-junction photovoltaics offer a promising route to surpass the efficiency limitations of single-junction solar cells, yet existing high-performance architectures are predominantly rigid and relatively heavy, limiting their use in weight-sensitive applications. Here, we report, to the best of our knowledge, the first ultra-lightweight and flexible monolithic perovskiteperovskite–organic triple-junction tandem solar cells. The devices integrate 2.05 eV and 1.62 eV perovskite front and middle subcells with a 1.33 eV organic bulk-heterojunction rear subcell on a 10 μm flexible polyethylene terephthalate substrate. The champion tandem device achieves a power conversion efficiency of 24.1%, with an open-circuit voltage of 3.27 V, a short-circuit current density of 9.32 mA/cm2, and a fill factor of 79.0%, corresponding to a power-per-weight of 11.2 W/g. The device exhibits a stabilized PCE of 24.6% under maximumpower-point tracking and negligible hysteresis between forward and reverse voltage scans. External quantum efficiency measurements yield closely matched integrated photocurrent densities of 9.39, 9.39, and 9.21 mA/cm2 for the three subcells, confirming efficient spectral utilization and current matching. These results establish flexible perovskite–perovskiteorganic triple-junction tandems as a promising platform for high-specific-power photovoltaics and open opportunities for lightweight energy harvesting in aerospace, unmanned aerial vehicles, wearable electronics, and portable power systems.
- Top Cited Papers
- 8 January 2026
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 391 (6781) , 153-159
Multivalent ligands regulate dimensional engineering for inverted perovskite solar modules
Multivalent, resonance-stabilized amidinium ligands enable stronger chemical coordination and reduced deprotonation compared with conventional monovalent ammonium ligands in low-dimensional perovskites. Here, we introduce a controllable one- to two-dimensional (1D-to-2D) structural transition strategy by systematically tuning ligand conformation, thereby modulating hydrogen bonding, π–π stacking, and basicity to elucidate the relationship between molecular structure, interfacial interactions, and resulting dimensionality. The 1D-amidinium perovskite structure, with its pronounced geometric anisotropy, impedes uniform surface coverage and defect passivation. In contrast, the 2D-amidinium perovskite forms a continuous, homogeneous interfacial layer, enabling more effective defect passivation and favorable energy-level alignment. With dimensionality control, inverted 3D/2D-amidinium perovskite solar cells deliver 25.4% power conversion efficiency (1.1 square centimeters, steady-state certified) and maintain >95% of their initial efficiency after 1100 hours of continuous 1-sun operation at 85°C.
- 8 January 2026
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 391 (6781) , 153-159
Top Cited PapersMultivalent ligands regulate dimensional engineering for inverted perovskite solar modules
Multivalent, resonance-stabilized amidinium ligands enable stronger chemical coordination and reduced deprotonation compared with conventional monovalent ammonium ligands in low-dimensional perovskites. Here, we introduce a controllable one- to two-dimensional (1D-to-2D) structural transition strategy by systematically tuning ligand conformation, thereby modulating hydrogen bonding, π–π stacking, and basicity to elucidate the relationship between molecular structure, interfacial interactions, and resulting dimensionality. The 1D-amidinium perovskite structure, with its pronounced geometric anisotropy, impedes uniform surface coverage and defect passivation. In contrast, the 2D-amidinium perovskite forms a continuous, homogeneous interfacial layer, enabling more effective defect passivation and favorable energy-level alignment. With dimensionality control, inverted 3D/2D-amidinium perovskite solar cells deliver 25.4% power conversion efficiency (1.1 square centimeters, steady-state certified) and maintain >95% of their initial efficiency after 1100 hours of continuous 1-sun operation at 85°C.
- Top Cited PapersOpen Access
- 3 November 2025
- Published by Springer Nature in Nature Photonics
- Vol. 19 (11) , 1178-1188
Guidelines for accurate evaluation of photodetectors based on emerging semiconductor technologies
- 3 November 2025
- Published by Springer Nature in Nature Photonics
- Vol. 19 (11) , 1178-1188
Top Cited PapersOpen AccessGuidelines for accurate evaluation of photodetectors based on emerging semiconductor technologies
- 25 May 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (22) , 10134-10149
Perovskite/Silicon Tandem Photovoltaics: Long-Term Stability through Interface Engineering
- 25 May 2025
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 39 (22) , 10134-10149
Perovskite/Silicon Tandem Photovoltaics: Long-Term Stability through Interface Engineering
- Top Cited PapersOpen Access
- 26 January 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-10
Solvent-dripping modulated 3D/2D heterostructures for high-performance perovskite solar cells
The controlled growth of two-dimensional (2D) perovskite atop three-dimensional (3D) perovskite films reduces interfacial recombination and impedes ion migration, thus improving the performance and stability of perovskite solar cells (PSCs). Unfortunately, the random orientation of the spontaneously formed 2D phase atop the pre-deposited 3D perovskite film can deteriorate charge extraction owing to energetic disorder, limiting the maximum attainable efficiency and long-term stability of the PSCs. Here, we introduce a meta-amidinopyridine ligand and the solvent post-dripping step to generate a highly ordered 2D perovskite phase on the surface of a 3D perovskite film. The reconstructed 2D/3D perovskite interface exhibits reduced energetic disorder and yields cells with improved performance compared with control 2D/3D samples. PSCs fabricated with the meta-amidinopyridine-induced phase-pure 2D perovskite passivation show a maximum power conversion efficiency of 26.05% (a certified value of 25.44%). Under damp heat and outdoor tests, the encapsulated PSCs maintain 82% and 75% of their initial PCE after 1000 h and 840 h, respectively, demonstrating improved practical durability.
- 26 January 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-10
Top Cited PapersOpen AccessSolvent-dripping modulated 3D/2D heterostructures for high-performance perovskite solar cells
The controlled growth of two-dimensional (2D) perovskite atop three-dimensional (3D) perovskite films reduces interfacial recombination and impedes ion migration, thus improving the performance and stability of perovskite solar cells (PSCs). Unfortunately, the random orientation of the spontaneously formed 2D phase atop the pre-deposited 3D perovskite film can deteriorate charge extraction owing to energetic disorder, limiting the maximum attainable efficiency and long-term stability of the PSCs. Here, we introduce a meta-amidinopyridine ligand and the solvent post-dripping step to generate a highly ordered 2D perovskite phase on the surface of a 3D perovskite film. The reconstructed 2D/3D perovskite interface exhibits reduced energetic disorder and yields cells with improved performance compared with control 2D/3D samples. PSCs fabricated with the meta-amidinopyridine-induced phase-pure 2D perovskite passivation show a maximum power conversion efficiency of 26.05% (a certified value of 25.44%). Under damp heat and outdoor tests, the encapsulated PSCs maintain 82% and 75% of their initial PCE after 1000 h and 840 h, respectively, demonstrating improved practical durability.
- 19 November 2024
- Published by Wiley in Advanced Energy Materials
- Vol. 15 (1)
Self‐Assembled Monolayer Dyes for Contact‐Passivated and Stable Perovskite Solar Cells
Surface modification of transparent conductive oxides (TCOs) with carbazole‐based self‐assembled monolayers (SAMs) is an effective method toward the formation of highly efficient hole‐selective contacts, enabling the fabrication of high‐performance perovskite solar cells (PSCs). However, the lack of long‐term structural and performance stability of the TCO/SAM/perovskite stack endangers the market entry of PSCs. Here, it is demonstrated that these challenges can be overcome by employing dyes as multi‐functional SAMs, simultaneously facilitating charge transport, passivating interfacial defects, and acting as a “molecular adhesive” layer, preserving structural integrity of the contact stack. Particularly, the surface modification of ITO with a dye (N719) monolayer is shown to create a hole‐selective contact for the fabrication of p–i–n PSCs with power conversion efficiencies reaching 24%. The N719 SAM‐based PSCs have also shown superior stability compared to state‐of‐the‐art PSCs incorporating carbazole SAMs and polyarylamine hole‐selective contacts by preserving ≈90% of their initial PCE under continuous light and thermal stress tests for 1000 h. The robustness of the ITO/N719/perovskite stack is attributed to its low interfacial trap density, UV resilience and strong adhesion capability. These findings place dye SAMs as a promising alternative for improving the performance of next‐generation photovoltaics.
- 19 November 2024
- Published by Wiley in Advanced Energy Materials
- Vol. 15 (1)
Self‐Assembled Monolayer Dyes for Contact‐Passivated and Stable Perovskite Solar Cells
Surface modification of transparent conductive oxides (TCOs) with carbazole‐based self‐assembled monolayers (SAMs) is an effective method toward the formation of highly efficient hole‐selective contacts, enabling the fabrication of high‐performance perovskite solar cells (PSCs). However, the lack of long‐term structural and performance stability of the TCO/SAM/perovskite stack endangers the market entry of PSCs. Here, it is demonstrated that these challenges can be overcome by employing dyes as multi‐functional SAMs, simultaneously facilitating charge transport, passivating interfacial defects, and acting as a “molecular adhesive” layer, preserving structural integrity of the contact stack. Particularly, the surface modification of ITO with a dye (N719) monolayer is shown to create a hole‐selective contact for the fabrication of p–i–n PSCs with power conversion efficiencies reaching 24%. The N719 SAM‐based PSCs have also shown superior stability compared to state‐of‐the‐art PSCs incorporating carbazole SAMs and polyarylamine hole‐selective contacts by preserving ≈90% of their initial PCE under continuous light and thermal stress tests for 1000 h. The robustness of the ITO/N719/perovskite stack is attributed to its low interfacial trap density, UV resilience and strong adhesion capability. These findings place dye SAMs as a promising alternative for improving the performance of next‐generation photovoltaics.
- Open Access
- 30 September 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (45) , 31301-31311
Stable perovskite solar cells with exfoliated graphite as an ion diffusion-blocking layer
Spray-coated exfoliated graphite interlayer films inserted in perovskite solar cells block ion and metal diffusion. This approach produced devices with 25% power conversion efficiency and significantly improved operational stability.
- 30 September 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (45) , 31301-31311
Open AccessStable perovskite solar cells with exfoliated graphite as an ion diffusion-blocking layer
Spray-coated exfoliated graphite interlayer films inserted in perovskite solar cells block ion and metal diffusion. This approach produced devices with 25% power conversion efficiency and significantly improved operational stability.
- Open Access
- 27 June 2024
- Published by American Physical Society (APS) in PRX Energy
- Vol. 3 (2) , 023011
Novel Detection Scheme for Temporal and Spectral X-Ray Optical Analysis: Study of Triple-Cation Perovskites
Multimodal x-ray microscopy is key to assessing the property-functionality relationships of semiconductor devices with the utmost sensitivity and spatial resolution. Here, we report on a novel setup—the “Analyzer of X-ray excited Optical Luminescence Offering Temporal and spectraL resolution” (AXOLOTL)—and demonstrate its use by investigating a series of triple-cation mixed-halide perovskite solar cells (PSCs) with varying content. These PSCs exhibit spatially varying performance and are thus ideally probed by multimodal x-ray microscopy to elucidate the origin of the performance variations. Specifically, our nanoscale characterization of the wrinkled perovskite photoabsorber unveils a segregation of and , which is accompanied by a narrowed band gap and an increased charge-carrier lifetime in thick absorber areas. Overall, we demonstrate with this technique the spatial correlation of compositional inhomogeneities, topography, electrical performance, and optical performance, which is of highest interest for identifying loss mechanisms at the nanoscale in high-performance electronic device development, including solar cells.- 27 June 2024
- Published by American Physical Society (APS) in PRX Energy
- Vol. 3 (2) , 023011
Open AccessNovel Detection Scheme for Temporal and Spectral X-Ray Optical Analysis: Study of Triple-Cation Perovskites
Multimodal x-ray microscopy is key to assessing the property-functionality relationships of semiconductor devices with the utmost sensitivity and spatial resolution. Here, we report on a novel setup—the “Analyzer of X-ray excited Optical Luminescence Offering Temporal and spectraL resolution” (AXOLOTL)—and demonstrate its use by investigating a series of triple-cation mixed-halide perovskite solar cells (PSCs) with varying content. These PSCs exhibit spatially varying performance and are thus ideally probed by multimodal x-ray microscopy to elucidate the origin of the performance variations. Specifically, our nanoscale characterization of the wrinkled perovskite photoabsorber unveils a segregation of and , which is accompanied by a narrowed band gap and an increased charge-carrier lifetime in thick absorber areas. Overall, we demonstrate with this technique the spatial correlation of compositional inhomogeneities, topography, electrical performance, and optical performance, which is of highest interest for identifying loss mechanisms at the nanoscale in high-performance electronic device development, including solar cells. - Open Access
- 11 May 2024
- Published by Wiley in Energy & Environmental Materials
- Vol. 7 (5)
Stable Organic Solar Cells Enabled by Simultaneous Hole and Electron Interlayer Engineering
The development of high‐performance organic solar cells (OSCs) with high operational stability is essential to accelerate their commercialization. Unfortunately, our understanding of the origin of instabilities in state‐of‐the‐art OSCs based on bulk heterojunction (BHJ) featuring non‐fullerene acceptors (NFAs) remains limited. Herein, we developed NFA‐based OSCs using different charge extraction interlayer materials and studied their storage, thermal, and operational stabilities. Despite the high power conversion efficiency (PCE) of the OSCs (17.54%), we found that cells featuring self‐assembled monolayers (SAMs) as hole‐extraction interlayers exhibited poor stability. The time required for these OSCs to reach 80% of their initial performance (T80) was only 6 h under continuous thermal stress at 85 °C in a nitrogen atmosphere and 1 h under maximum power point tracking (MPPT) in a vacuum. Inserting MoOx between ITO and SAM enhanced the T80 to 50 and ~15 h after the thermal and operational stability tests, respectively, while maintaining a PCE of 16.9%. Replacing the organic PDINN electron transport layer with ZnO NPs further enhances the cells' thermal and operational stability, boosting the T80 to 1000 and 170 h, respectively. Our work reveals the synergistic roles of charge‐selective interlayers and device architecture in developing efficient and stable OSCs.
- 11 May 2024
- Published by Wiley in Energy & Environmental Materials
- Vol. 7 (5)
Open AccessStable Organic Solar Cells Enabled by Simultaneous Hole and Electron Interlayer Engineering
The development of high‐performance organic solar cells (OSCs) with high operational stability is essential to accelerate their commercialization. Unfortunately, our understanding of the origin of instabilities in state‐of‐the‐art OSCs based on bulk heterojunction (BHJ) featuring non‐fullerene acceptors (NFAs) remains limited. Herein, we developed NFA‐based OSCs using different charge extraction interlayer materials and studied their storage, thermal, and operational stabilities. Despite the high power conversion efficiency (PCE) of the OSCs (17.54%), we found that cells featuring self‐assembled monolayers (SAMs) as hole‐extraction interlayers exhibited poor stability. The time required for these OSCs to reach 80% of their initial performance (T80) was only 6 h under continuous thermal stress at 85 °C in a nitrogen atmosphere and 1 h under maximum power point tracking (MPPT) in a vacuum. Inserting MoOx between ITO and SAM enhanced the T80 to 50 and ~15 h after the thermal and operational stability tests, respectively, while maintaining a PCE of 16.9%. Replacing the organic PDINN electron transport layer with ZnO NPs further enhances the cells' thermal and operational stability, boosting the T80 to 1000 and 170 h, respectively. Our work reveals the synergistic roles of charge‐selective interlayers and device architecture in developing efficient and stable OSCs.
- Open Access
- 23 October 2023
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 10 (4)
A critical perspective for emerging ultra-thin solar cells with ultra-high power-per-weight outputs
Ultrathin, solution-processed emerging solar cells with high power-per-weight (PPW) outputs demonstrate unique potential for applications where low weight, high power output, and flexibility are indispensable. The following perspective explores the literature of emerging PVs and highlights the maximum reported PPW values of perovskite solar cells (PSCs) 29.4 W/g, organic solar cells (OSCs) 32.07 W/g, and quantum dot solar cells 15.02 W/g, respectively. The record PPW values of OSCs and PSCs are approximately one order of magnitude higher compared to their inorganic ultrathin solar cells counterparts (approximately 3.2 W/g for CIGS and a-Si). This consists emerging PVs, very attractive for a variety of applications where the PPW is the key parameter. In particular, both OSCs and PSCs can be implemented in different scenarios of applications (indoor and biocompatible applications for OSCs and outdoor and high-energy radiation conversion conditions for the PSCs) due to their unique optoelectronic and physiochemical properties. Finally, our theoretical optical and electrical simulation and optimization study for the most promising and well-suited PV technologies showed an impressive maximum realistic theoretical PPW limit of 74.3 and 93.7 W/g for PSCs and OSCs, respectively. Our finding in the theoretical section shows that the experimental results achieved in the literature of PSCs and OSCs toward high PPW outputs is not quite close to the theoretical maximum (35% and 40% of the theoretical maximum for OSCs and PSCs, respectively), and thus, more work needs to be done to further increase the experimental PPW output of these promising PV technologies.
- 23 October 2023
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 10 (4)
Open AccessA critical perspective for emerging ultra-thin solar cells with ultra-high power-per-weight outputs
Ultrathin, solution-processed emerging solar cells with high power-per-weight (PPW) outputs demonstrate unique potential for applications where low weight, high power output, and flexibility are indispensable. The following perspective explores the literature of emerging PVs and highlights the maximum reported PPW values of perovskite solar cells (PSCs) 29.4 W/g, organic solar cells (OSCs) 32.07 W/g, and quantum dot solar cells 15.02 W/g, respectively. The record PPW values of OSCs and PSCs are approximately one order of magnitude higher compared to their inorganic ultrathin solar cells counterparts (approximately 3.2 W/g for CIGS and a-Si). This consists emerging PVs, very attractive for a variety of applications where the PPW is the key parameter. In particular, both OSCs and PSCs can be implemented in different scenarios of applications (indoor and biocompatible applications for OSCs and outdoor and high-energy radiation conversion conditions for the PSCs) due to their unique optoelectronic and physiochemical properties. Finally, our theoretical optical and electrical simulation and optimization study for the most promising and well-suited PV technologies showed an impressive maximum realistic theoretical PPW limit of 74.3 and 93.7 W/g for PSCs and OSCs, respectively. Our finding in the theoretical section shows that the experimental results achieved in the literature of PSCs and OSCs toward high PPW outputs is not quite close to the theoretical maximum (35% and 40% of the theoretical maximum for OSCs and PSCs, respectively), and thus, more work needs to be done to further increase the experimental PPW output of these promising PV technologies.