Daniel Russell Houck

To validate the second‐by‐second dynamics of turbines in field experiments, it is necessary to accurately reconstruct the winds going into the turbine. Current time‐resolved inflow reconstruction techniques estimate wind behavior in unobserved regions using relatively simple spectral‐based models of the atmosphere. Here, we develop a technique for time‐resolved inflow reconstruction that is rooted in a large‐eddy simulation model of the atmosphere. Our “large‐eddy reconstruction” technique blends observations and atmospheric model information through a diffusion model machine learning algorithm, allowing us to generate probabilistic ensembles of reconstructions for a single 10‐min observational period. Our generated inflows can be used directly by aeroelastic codes or as inflow boundary conditions in a large‐eddy simulation. We verify the second‐by‐second reconstruction capability of our technique in three synthetic field campaigns, finding positive Pearson correlation coefficient values () between ground‐truth and reconstructed streamwise velocity, as well as smaller positive correlation coefficient values for unobserved fields (spanwise velocity, vertical velocity, and temperature). We validate our technique in three real‐world case studies by driving large‐eddy simulations with reconstructed inflows and comparing to independent inflow measurements. The reconstructions are visually similar to measurements, follow desired power spectra properties, and track second‐by‐second behavior ().

In previous work, comparisons were made between large-scale simulations of the American Wake ExperimeNt (AWAKEN) wind farms conducted using the large-eddy simulation (LES) codes Nalu-Wind and Adaptive Mesh Refinement-Wind, the engineering wind farm model FLOw Redirection and Induction in Steady State (FLORIS), and the multi-scale Weather Research and Forecasting model. Significant discrepancies were observed in the modeled wake deficits, and the present paper investigates the sources of this model variability using new simulations with single turbines and smaller domains. From an experimental data set taken from AWAKEN, an idealized neutral stability condition was defined and single-turbine cases using actuator disk were conducted with the different simulation codes allowing for a comprehensive investigation into the similarities and differences between the atmospheric inflow, turbines, and wakes of the simulations. Improvements to the simulation setups in the present study resulted in significantly higher agreement between the modeled results from the three LES models and FLORIS.

In this study, we consider the impact of large-scale, convective structures in an unstable atmospheric boundary layer on wind turbine wakes. Simulation data from a high-fidelity large-eddy simulation (LES) of the AWAKEN wind farm site matching unstable atmospheric conditions were analyzed, and both turbine performance and wake behavior were affected based on their location relative to the convective structures. Turbines located in updraft regions of the flow experienced lower inflow velocity and generated less power, but their wakes were observed to recover faster and saw greater turbulent kinetic energy mixing higher in the boundary layer. The opposite effect was found for turbines in the downdraft regions of the convective structures. A simplified model of this wake behavior was also developed based on a two-dimensional k–ε Reynolds-Averaged Navier–Stokes formulation. This simplified model included the effects of vertical transport, but could be efficiently solved as a parabolic system, and was found to capture similar wake modifications observed in the high-fidelity LES computations.

In this work, we develop a new analytical turbine induction model that can incorporate complex inflow conditions including cases where the wind velocity and temperature profiles can vary as functions of height. This induction model is derived from the linearized Navier–Stokes and leads to a second‐order ODE that can be solved using a Green's function formulation. The corresponding Green's function for several configurations are found including the infinite domain, semi‐infinite domain with ground plane, and a power law velocity inflow profile. The results of this approach are then compared with simulations of the turbine induction field using the AMR‐Wind CFD solver with a uniformly loaded actuator disk model. These comparisons show that the Green's function approach captures the centerline blockage, three‐dimensional blockage flow field, and streamwise velocity slow down, with very good agreement for lower thrust conditions and at larger distances away from rotor disk. The effects of shear on the turbine blockage were also compared using a power law inflow profile, and we show that this approach matches the CFD predictions for the cases considered.

The Additively‐Manufactured, System‐Integrated Tip (AMSIT) project is leveraging the flexibility of 3D printing to integrate several technologies in a wind turbine blade tip, while reducing the levelized cost of electricity (LCOE) produced. The design integration is demonstrated for a 200‐kW–scale turbine with 13‐m blades, with the outer 15% of the blade replaced with a 3D‐printed design. Aerodynamic performance is enhanced without increasing swept area through inclusion of a winglet and surface texturing, both challenging for traditional manufacturing. Longevity and durability are improved through integrated lightning and leading edge erosion protection. Increased power, reduced repair frequency, and ease of repair through blade modularity all contribute to reduced LCOE. The analysis is also extended to modern MW‐scale designs to estimate the impact of the technology at scale, demonstrating the potential to reduce LCOE significantly for modern onshore turbines, with even higher potential savings offshore.