JJJeong Beom Jang

Jeong Beom Jang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jeong Beom Jang has a total of 9 co-authors. Here are the top co-authors by number of shared publications:

  • Bongkuk Seo

    Research Center for Advanced Specialty Chemicals, Korea Research Institute of Chemical Technology, 45, Jongga-ro, Yugok-dong, Jung-gu, Ulsan 44412, Korea

    2 shared publications
  • Choong-Sun Lim

    Research Center for Advanced Specialty Chemicals, Korea Research Institute of Chemical Technology Ulsan Republic of Korea

    2 shared publications
  • Tae Hee Kim

    Research Center for Advanced Specialty Chemicals, Korea Research Institute of Chemical Technology, 45, Jongga-ro, Yugok-dong, Jung-gu, Ulsan 44412, Korea

    2 shared publications
  • Wonjoo Lee

    Center for Advanced Specialty Chemicals, Korea Research Institute of Chemical Technology, Ulsan 44412, Republic of Korea

    2 shared publications
  • Hye Jin Kim

    The Center for Chemical Industry Development, Korea Research Institute of Chemical Technology, 45, Jongga-ro, Yugok-dong, Jung-gu, Ulsan 44412, Korea

    1 shared publication
  • Hye Jin Kim

    Research Center for Advanced Specialty Chemicals, Korea Research Institute of Chemical Technology, 45, Jongga-ro, Yugok-dong, Jung-gu, Ulsan 44412, Korea

    1 shared publication

Latest Publications

  • Open Access

    Synthesis of Waterborne Polyurethane Using Phosphorus-Modified Rigid Polyol and its Physical Properties

    by Taewoo Jang, Hye Jin Kim, Jeong Beom Jang, Tae Hee Kim, Wonjoo Lee, Bongkuk Seo, Weon Bae Ko, Choong-Sun Lim

    In this study, a phosphorous-containing polyol (P-polyol) was synthesized and reacted with isophorone diisocyanate (IPDI) to produce water-dispersed polyurethane. To synthesize waterborne polyurethanes (WPUs), mixtures of P-polyol and polycarbonate diol (PCD) were reacted with IPDI, followed by the addition of dimethylol propionic acid, to confer hydrophilicity to the produced polyurethane. An excess amount of water was used to disperse polyurethane in water, and the terminal isocyanate groups of the resulting WPUs were capped with ethylene diamine. P-polyol:PCD molar ratios of 0.1:0.9, 0.2:0.8, and 0.3:0.7 were used to synthesize WPUs. The films prepared by casting and drying the synthesized WPUs in plastic Petri dishes were used to test the changes in physical properties induced by changing the P-polyol:PCD molar ratio. The experimental results revealed that the tensile strength of PU-10, the WPU with a P-polyol:PCD molar ratio of 0.1:0.9, was 16% higher than that of the reference P-polyol–free WPU sample. Moreover, the thermal decomposition temperature of PU-10 was 27 °C higher than that of the reference sample.


  • Open Access

    Modified Epoxy Resin Synthesis from Phosphorus—Containing Polyol and Physical Changes Studies in the Synthesized Products

    by Jeong Beom Jang, Tae Hee Kim, Taeyoon Kim, Hye Jin Kim, Bongkuk Seo, Choong-Sun Lim, Wonjoo Lee

    Epoxy resins are commonly used to manufacture the molding compounds, reinforced plastics, coatings, or adhesives required in various industries. However, the demand for new epoxy resins has increased to satisfy diverse industrial requirements such as enhanced mechanical properties, thermal stability, or electrical properties. Therefore, in this study, we synthesized new epoxy resin (PPME) by modifying phosphorous-containing polyol. The prepared resin was analyzed and added to epoxy compositions in various quantities. The compositions were cured at high temperatures to obtain plastics to further test the mechanical and thermal properties of the epoxy resin. The measured tensile and flexural strength of epoxy compositions were similar to the composition without synthesized epoxy resin. However, the heat release rates of the compositions exhibited tendencies of a decrease proportional to the amount of PPME.