Guangxu Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Guangxu Zhang has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Chao Xu
School of Chemistry, Chemical Engineering and Life Science, Wuhan University of Technology, Wuhan 430070, Hubei, China
2 shared publications- Wen-Jin Xu
School of Chemistry, Chemical Engineering and Life Science, Wuhan University of Technology, Wuhan 430070, Hubei, China
2 shared publications Xiaocong Ren
Department of Biotechnology, ZhiXing College of HuBei University, Wuhan, China
2 shared publicationsDachuan Xia
School of Chemistry, Chemical Engineering and Life Sciences, Wuhan University of Technology, Wuhan 430070, China
1 shared publication- Gang-Gang Chang
Wuhan University of Technology
1 shared publication Guanwen Chen
School of Chemistry, Chemical Engineering and Life Sciences, Wuhan University of Technology, Wuhan 430070, China
1 shared publication
Latest Publications
- 17 May 2025
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 40 (3) , 674-681
Mechanism of NO Adsorption on H-ZSM-5 under Aerobic Atmosphere
- 17 May 2025
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 40 (3) , 674-681
Mechanism of NO Adsorption on H-ZSM-5 under Aerobic Atmosphere
- 14 November 2023
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 127 (46) , 22548-22556
Effective Utilization of Low NO Concentration for the Electrochemical Synthesis of NH3
- 14 November 2023
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 127 (46) , 22548-22556
Effective Utilization of Low NO Concentration for the Electrochemical Synthesis of NH3
- 28 October 2020
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 99 (4) , 999-1010
Kinetics study and process simulation of reactive distillation for the synthesis of ε‐caprolactone
- 28 October 2020
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 99 (4) , 999-1010
Kinetics study and process simulation of reactive distillation for the synthesis of ε‐caprolactone
- Open Access
The Corrosion Features of Q235B Steel under Immersion Test and Electrochemical Measurements in Desulfurization Solution
With the continuous tightening marine diesel engines emission standards, removing sulfur oxides (SOX) by sodium hydroxide solution absorption is a highly efficiency and economic method, which has been a hot area of research. The ensuing desulfurization solution is a new corrosive system, the aim of this paper is to ascertain the corrosion feature of Q235B steel in desulfurization solution, which lays a theoretical foundation for industrialization. For this purpose, mass loss, electrochemical techniques and surface analyses were applied. The results of mass loss highlight a reduction in the corrosion rate with 35 days of immersion. Higher exposure time increased the compactness of the corrosion product layer and changed phase composition. These conclusions are supported by surface analyses, such as X-ray diffraction and scanning electron microscope. However, electrochemical results showed that the polarization resistance Rp was fluctuant. Both of Rp and charge transfer resistance Rt reach a maximum after immersing 21 days. In addition, although the sediments attached to the steel surface could inhibit corrosion, pitting corrosion aggravated by hydrolyzation of FeSO4 should be given more attention.
Open AccessThe Corrosion Features of Q235B Steel under Immersion Test and Electrochemical Measurements in Desulfurization Solution
With the continuous tightening marine diesel engines emission standards, removing sulfur oxides (SOX) by sodium hydroxide solution absorption is a highly efficiency and economic method, which has been a hot area of research. The ensuing desulfurization solution is a new corrosive system, the aim of this paper is to ascertain the corrosion feature of Q235B steel in desulfurization solution, which lays a theoretical foundation for industrialization. For this purpose, mass loss, electrochemical techniques and surface analyses were applied. The results of mass loss highlight a reduction in the corrosion rate with 35 days of immersion. Higher exposure time increased the compactness of the corrosion product layer and changed phase composition. These conclusions are supported by surface analyses, such as X-ray diffraction and scanning electron microscope. However, electrochemical results showed that the polarization resistance Rp was fluctuant. Both of Rp and charge transfer resistance Rt reach a maximum after immersing 21 days. In addition, although the sediments attached to the steel surface could inhibit corrosion, pitting corrosion aggravated by hydrolyzation of FeSO4 should be given more attention.
- 6 December 2019
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 58 (51) , 22875-22883
Highly Efficient Heterogeneous Catalytic Reduction of Fe(II)EDTA-NO in Industrial Denitrification Solution over Pd/AC Catalyst
- 6 December 2019
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 58 (51) , 22875-22883
Highly Efficient Heterogeneous Catalytic Reduction of Fe(II)EDTA-NO in Industrial Denitrification Solution over Pd/AC Catalyst
- 18 February 2019
- Published by Taylor & Francis in Environmental Technology
- Vol. 41 (21) , 2705-2715
Highly efficient absorption of nitric oxide by RuIII(edta) aqueous solutions at low concentrations
In this paper, RuIII(edta) was used as a highly efficient absorbent for the removal of NO due to its desirable properties of high NO affinity and oxygen insensitivity. The effects of the RuIII(edta) concentration, reaction temperature, initial solution pH, oxygen concentration, inlet NO concentration, and liquid-to-gas ratio on denitration performance were examined. The results indicated that RuIII(edta) showed excellent denitration performance at low concentrations and that an increase in the concentration of RuIII(edta) resulted in an increase in NO removal efficiency. In addition, NO removal efficiency increased to its optimum value at first and then declined as both the reaction temperature and initial solution pH rose. The optimal reaction temperature and ideal initial solution pH were determined to be 45°C and 5.0 respectively. The suitable liquid-to-gas ratio was found to be 51.5 L/m3. NO removal efficiency was less affected by the oxygen concentration in the range of 0–12% due to a superior anti-oxidation performance at pH = 5.0. Furthermore, the NO removal efficiency decreased significantly as the inlet NO concentration increased. The addition of 5 wt% urea to an aqueous solution of RuIII(edta) enhanced denitration performance, and an RuIII(edta) and urea mixed solution were able to exceed 65.07% NO removal efficiency within 30 min under optimal experimental conditions. This work proposed an alternative absorbent for NO removal and provided fundamental data for industrial denitration with RuIII(edta) absorbents. GRAPHICAL ABSTRACT
- 18 February 2019
- Published by Taylor & Francis in Environmental Technology
- Vol. 41 (21) , 2705-2715
Highly efficient absorption of nitric oxide by RuIII(edta) aqueous solutions at low concentrations
In this paper, RuIII(edta) was used as a highly efficient absorbent for the removal of NO due to its desirable properties of high NO affinity and oxygen insensitivity. The effects of the RuIII(edta) concentration, reaction temperature, initial solution pH, oxygen concentration, inlet NO concentration, and liquid-to-gas ratio on denitration performance were examined. The results indicated that RuIII(edta) showed excellent denitration performance at low concentrations and that an increase in the concentration of RuIII(edta) resulted in an increase in NO removal efficiency. In addition, NO removal efficiency increased to its optimum value at first and then declined as both the reaction temperature and initial solution pH rose. The optimal reaction temperature and ideal initial solution pH were determined to be 45°C and 5.0 respectively. The suitable liquid-to-gas ratio was found to be 51.5 L/m3. NO removal efficiency was less affected by the oxygen concentration in the range of 0–12% due to a superior anti-oxidation performance at pH = 5.0. Furthermore, the NO removal efficiency decreased significantly as the inlet NO concentration increased. The addition of 5 wt% urea to an aqueous solution of RuIII(edta) enhanced denitration performance, and an RuIII(edta) and urea mixed solution were able to exceed 65.07% NO removal efficiency within 30 min under optimal experimental conditions. This work proposed an alternative absorbent for NO removal and provided fundamental data for industrial denitration with RuIII(edta) absorbents. GRAPHICAL ABSTRACT
- 3 February 2016
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 31 (1) , 64-67
Synthesis, structural characterization and hydrogen storage of nickel-containing mesoporous MCM-48 by electroless plating
- 3 February 2016
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 31 (1) , 64-67
Synthesis, structural characterization and hydrogen storage of nickel-containing mesoporous MCM-48 by electroless plating
- 27 August 2015
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 54 (35) , 8670-8677
Absorption of Sulfur Dioxide with Sodium Hydroxide Solution in Spray Columns
- 27 August 2015
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 54 (35) , 8670-8677
Absorption of Sulfur Dioxide with Sodium Hydroxide Solution in Spray Columns