Piotr Bednarczuk

Purpose: The primary purpose of the study is to reconstruct the bladder based on the tomographic measurements obtained. Depending on the type of tomography used, two approaches are presented. Methods: In the first presented case, the measurements were collected using ultrasonic tomography, while in the second one, they were gathered with electrical impedance tomography. Deterministic methods and machine learning algorithms, such as Elastic Net, Least Angle Regression, and a Neural Network, were used to obtain the bladder reconstruction. Results: The bladder's position and size can be recognized based on the tomographic measurements of the UST and EIT. Both methods allow for its effective reconstruction. Discussion: The research results are satisfactory, but their effectiveness is debatable. Future studies will focus on comparing and optimizing both solutions regarding reconstruction time.

Methods of medical image segmentation analysis to improve the effectiveness of diagnosing lung diseases. The article aims to review selected methods for segmenting lung medical images based on computed tomography (CT) image data analysis. Included in the analysis are 11 different approaches, including edge algorithms such as Canny, Prewitt, Roberts, Sobel and Log, clustering-based algorithms such as Fuzzy C-means, genetic K-means, k-nearest neighbours, and neural networks such as perceptron, neural and fuzzy sets, and edge binarization techniques, among others. Each method was evaluated for its ability to segment lung structures on CT images accurately. Finally, the contour of the heart from the CT image was determined using the maximum entropy thresholding method. The juxtaposition of different approaches to medical image segmentation is an important contribution to developing medical diagnostic techniques, which can help improve the efficiency of diagnosing lung diseases.

Purpose: The research presented in this paper was conducted to obtain a detailed 3D model of the urinary bladder using electrical impedance tomography, a noninvasive tomographic technique. Methods: Electrical impedance tomography (EIT) is an imaging technique that measures electrical impedance inside the human body. Many methods, including those based on physical models and machine learning, are used to reconstruct the considered 3D object using EIT. The work focuses on the Gauss-Newton algorithm in its generalized form. Results: Three-dimensional reconstructions of the urinary bladder were obtained. The models are built with high accuracy and can be processed by subsequent algorithms. Discussion: The constructed models can serve as the basis for correct diagnosis in medicine and as research material for subsequent work, for example, on the possibilities of 3D printing. Possible methods of obtaining even higher-quality reconstruction also remain to be considered.

Problems related to reducing energy consumption constitute an important basis for scientific research worldwide. A proposal to use various renewable energy sources, including creating a biogas plant, is emphasized in the introduction of this article. However, the indicated solutions require continuous monitoring and control to maximise the installations’ effectiveness. The authors took up the challenge of developing a computer solution to reduce the costs of maintaining technological process monitoring systems. Concept diagrams of a metrological system using multi-sensor techniques containing humidity, temperature and pressure sensors coupled with Electrical Impedance Tomography (EIT) sensors were presented. This approach allows for effective monitoring of the anaerobic fermentation process. The possibility of reducing the energy consumed during installation operation was proposed, which resulted in the development of algorithms for determining alarm states, which are the basis for controlling the frequency of technological process measurements. Implementing the idea required the preparation of measurement infrastructure and an analytical engine based on AI techniques, including an expert system and developed algorithms. Numerous time-consuming studies and experiments have confirmed reduced energy consumption, which can be successfully used in biogas production.

Over time, systems connected to databases slow down. This is usually due to the increase in the amount of data stored in individual tables, counted even in the billions of records. Nevertheless, there are methods for making the speed of the system independent of the number of records in the database. One of these ways is table partitioning. When used correctly, the solution can ensure efficient operation of very large databases even after several years. However, not everything is predictable because of some undesirable phenomena become apparent only with a very large amount of data. The article presents a study of the execution time of the same queries with increasing number of records in a table. These studies reveal and present the timing and circumstances of the anomaly for a certain number of records.

This paper presents an application for the monitoring of leaks in flood embankments by reconstructing images in electrical tomography using logistic regression machine learning methods with elastic net regularisation, PCA and wave preprocessing. The main advantage of this solution is to obtain a more accurate spatial conductivity distribution inside the studied object. The described method assumes a learning system consisting of multiple equations working in parallel, where each equation creates a single point in the output image. This enables the efficient reconstruction of spatial images. The research focused on preparing, developing, and comparing algorithms and models for data analysis and reconstruction using a proprietary electrical tomography solution. A reliable measurement solution with sensors and machine learning methods makes it possible to analyse damage and leaks, leading to effective information and the eventual prevention of risks. The applied methods enable the improved resolution of the reconstructed images and the possibility to obtain them in real-time, which is their distinguishing feature compared to other methods. The use of electrical tomography in combination with specific methods for image reconstruction allows for an accurate spatial assessment of leaks and damage to dikes.

The paper presents a proposal of a complete CAD Automation solution enabling customization of the production of medical screws to individual patient requirements. The proposed approach using OLE technology enables the introduction of customization at the CAD project stage. The assembly of the surgical screw in the PLM system is generated by means of a specially developed application. The application communicates with the SolidEdge system using an API, taking into account 10 different input parameters. Three different types of medical screws have been developed in the application: the Herbert Screw, Cancellous Screw, and Malleolar Screw with three different thread types: rectangular, isosceles, and trapezoidal. The screws designed in this way can be manufactured using 3D printing techniques or CNC machining, and can be used for both humans and animals.

Very large databases like data warehouse slow down over time. This is usually due to a large daily increase in the data in the individual tables, counted in millions of records per day. How do we make sure our queries do not slow down over time? Table partitioning comes in handy, and, when used correctly, can ensure the smooth operation of very large databases with billions of records, even after several years. Bardzo duże bazy danych typu hurtownie danych z czasem zwalniają. Przyczyną zazwyczaj jest duży dzienny przyrost danych w pojedynczych tabelach liczony w milionach rekordów. Co sprawić aby z czasem nasze zapytania nie działały wolniej. Z pomocą przychodzi partycjonowanie tabel, które użyte w prawidłowy sposób może zapewnić sprawne działanie bardzo dużych bazy danych z miliardami rekordów nawet po kilku latach.

The article presents a solution based on a cyber-physical system in which data collected from measuring sensors was analysed for prediction in the production process control system. The presented technology was based on intelligent sensors as part of the solution for Industry 4.0. The main purpose of the work is to reduce data and select the appropriate covariate to optimise modelling of defects using the Cox model for a specific mechanical system. The reliability of machines and devices in the production process is a condition for ensuring continuity of production. Predicting damage, especially its movement, gives the ability to monitor the current state of the machine. In a broader perspective, this enables streamlining the production process, service planning or control. This ensures production continuity and optimal performance. The presented model is a regressive survival analysis model that allows you to calculate the probability of failure occurring over a given period of time.