Thomas E. Tiwald
Research Subjects
Thomas E. Tiwald has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Mathias Schubert
Department of Electrical and Computer Engineering, University of Nebraska-Lincoln 1 , Lincoln, Nebraska 68588
2 shared publications - Tino Hofmann
Department of Physics New Jersey Institute of Technology Newark New Jersey USA
2 shared publications A. A. Schafgans
Department of Physics, University of California–San Diego, La Jolla, California 92093, USA
1 shared publicationAli Naqavi
California Institute of Technology, Pasadena, CA 91125, USA
1 shared publication- Amitabha Sarkar
University of Nebraska, Lincoln, Electrical Engineering, Lincoln, Nebraska, United States
1 shared publication Anatoli Shkrebtii
UOIT, Science, Oshawa, Canada
1 shared publication
Latest Publications
- 26 September 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (13) , 131702
Far-field thermal radiation from short-pitch silicon-carbide nanopillar arrays
Silicon carbide (SiC) supports surface phonons in the infrared region of the electromagnetic spectrum where these modes can be thermally emitted. Additionally, the magnitude, spectrum, and direction of thermal radiation from SiC can be controlled by engineering this material at the sub-wavelength scale. For these reasons, SiC nanopillars are of high interest for thermal-radiation tuning. So far, theoretical and experimental studies of thermal emission from SiC nanopillars have been limited to long-pitch arrays with a microscale interpillar spacing. It is not clear how far-field thermal emission from SiC nanopillars is affected when the interparticle spacing reduces to the nanometer scale, where the near-field interaction between adjacent nanopillars arises and the array becomes zero order. In this Letter, we study physical mechanisms of far-field thermal radiation from zero-order arrays of silicon-carbide nanopillars with a nanoscale interpillar spacing. We show that the increased volume of thermal emitters and thermal radiation of the hybrid waveguide-surface-phonon-polariton mode from zero-order arrays increase the spectral emissivity of silicon carbide to values as large as 1 for a wide range of angles. The enhanced, dispersion-less thermal emission from a zero-order SiC array of nano-frustums with an optimized interspacing of 300 nm is experimentally demonstrated. Our study provides insight into thermal radiation from dense nanostructures and has significant implications for thermal management of electronic devices and energy harvesting applications.
- 26 September 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (13) , 131702
Far-field thermal radiation from short-pitch silicon-carbide nanopillar arrays
Silicon carbide (SiC) supports surface phonons in the infrared region of the electromagnetic spectrum where these modes can be thermally emitted. Additionally, the magnitude, spectrum, and direction of thermal radiation from SiC can be controlled by engineering this material at the sub-wavelength scale. For these reasons, SiC nanopillars are of high interest for thermal-radiation tuning. So far, theoretical and experimental studies of thermal emission from SiC nanopillars have been limited to long-pitch arrays with a microscale interpillar spacing. It is not clear how far-field thermal emission from SiC nanopillars is affected when the interparticle spacing reduces to the nanometer scale, where the near-field interaction between adjacent nanopillars arises and the array becomes zero order. In this Letter, we study physical mechanisms of far-field thermal radiation from zero-order arrays of silicon-carbide nanopillars with a nanoscale interpillar spacing. We show that the increased volume of thermal emitters and thermal radiation of the hybrid waveguide-surface-phonon-polariton mode from zero-order arrays increase the spectral emissivity of silicon carbide to values as large as 1 for a wide range of angles. The enhanced, dispersion-less thermal emission from a zero-order SiC array of nano-frustums with an optimized interspacing of 300 nm is experimentally demonstrated. Our study provides insight into thermal radiation from dense nanostructures and has significant implications for thermal management of electronic devices and energy harvesting applications.
- 10 March 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (8) , 2412-2421
Combining spectroscopic techniques to determine the optical constants of powdered lactose
A method for deriving the optical constants ( n / k ) of organic powdered materials using pressed pellets in the mid-infrared spectral range is introduced that combines variable angle spectroscopic ellipsometry and transmission spectroscopy. The approach is applied to anhydrous lactose, in which three different forms of pellets were pressed and measured: a pure lactose pellet and a mixed lactose/potassium bromide (KBr) pellet with a large analyte percentage were used for ellipsometric measurements, and a KBr transmission pellet with only a small analyte percentage was used for transmission measurements. The transmittance data provide an initial set of oscillators and improve the spectral fitting of weak absorption features ( k < 0.01 ). Ellipsometric data for the pure and mixed pellets are then fit simultaneously to derive the final n / k values for lactose from 6000 − 400 c m − 1 . An alternative method just using the ellipsometric data from the mixed pellet and the transmittance data is also presented and shows good agreement with the multi-sample analysis, providing a simpler method for powders that do not press easily into pure pellets. Finally, the derived optical constants were used to model the reflectance data, demonstrating a good match with the measured reflectance spectra if non-idealities are included.
- 10 March 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (8) , 2412-2421
Combining spectroscopic techniques to determine the optical constants of powdered lactose
A method for deriving the optical constants ( n / k ) of organic powdered materials using pressed pellets in the mid-infrared spectral range is introduced that combines variable angle spectroscopic ellipsometry and transmission spectroscopy. The approach is applied to anhydrous lactose, in which three different forms of pellets were pressed and measured: a pure lactose pellet and a mixed lactose/potassium bromide (KBr) pellet with a large analyte percentage were used for ellipsometric measurements, and a KBr transmission pellet with only a small analyte percentage was used for transmission measurements. The transmittance data provide an initial set of oscillators and improve the spectral fitting of weak absorption features ( k < 0.01 ). Ellipsometric data for the pure and mixed pellets are then fit simultaneously to derive the final n / k values for lactose from 6000 − 400 c m − 1 . An alternative method just using the ellipsometric data from the mixed pellet and the transmittance data is also presented and shows good agreement with the multi-sample analysis, providing a simpler method for powders that do not press easily into pure pellets. Finally, the derived optical constants were used to model the reflectance data, demonstrating a good match with the measured reflectance spectra if non-idealities are included.
- 18 December 2019
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 38 (1) , 012202
Temperature dependent dielectric function and direct bandgap of Ge
The dielectric function of bulk Ge is determined between 0.5 and 6.3 eV in a temperature range of 10–738 K using spectroscopic ellipsometry. The authors provide the data in a tabulated format that can be interpolated as a function of photon energy and temperature using commercial software. Another focus of this paper lies on the analysis of critical points, in particular, on the investigation of the temperature dependence of the direct bandgap E0 and the critical point E0+Δ0, where Δ0 is the spin–orbit splitting. To explore the temperature dependence of critical points, the parameters that characterize their line shapes are calculated using three different techniques. First, the common method of numerically calculating and analyzing the second derivatives of the dielectric function works well for critical points at higher energies. Second, an analysis in reciprocal space by performing a discrete Fourier transform and analyzing the resulting Fourier coefficients yields values for the energies of E0 and E0+Δ0. Third, the energy determined from a parametric semiconductor model is shown as a function of temperature. The authors observe a temperature dependent redshift of the E0 and E0+Δ0 critical point energies as well as an increase in the broadening of E0 with temperature.
- 18 December 2019
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 38 (1) , 012202
Temperature dependent dielectric function and direct bandgap of Ge
The dielectric function of bulk Ge is determined between 0.5 and 6.3 eV in a temperature range of 10–738 K using spectroscopic ellipsometry. The authors provide the data in a tabulated format that can be interpolated as a function of photon energy and temperature using commercial software. Another focus of this paper lies on the analysis of critical points, in particular, on the investigation of the temperature dependence of the direct bandgap E0 and the critical point E0+Δ0, where Δ0 is the spin–orbit splitting. To explore the temperature dependence of critical points, the parameters that characterize their line shapes are calculated using three different techniques. First, the common method of numerically calculating and analyzing the second derivatives of the dielectric function works well for critical points at higher energies. Second, an analysis in reciprocal space by performing a discrete Fourier transform and analyzing the resulting Fourier coefficients yields values for the energies of E0 and E0+Δ0. Third, the energy determined from a parametric semiconductor model is shown as a function of temperature. The authors observe a temperature dependent redshift of the E0 and E0+Δ0 critical point energies as well as an increase in the broadening of E0 with temperature.
- 18 December 2019
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 38 (1) , 014001
Application of a B-spline model dielectric function to infrared spectroscopic ellipsometry data analysis
The flexibility of the Kramers–Kronig-consistent basis spline (B-spline) function provides advantages over traditional physics-based oscillator functions for analyzing infrared spectroscopic ellipsometry data. Oscillator functions require that the user identify the spectral location of every absorption, choose the correct oscillator line shape, and choose the correct number of oscillators (which can be difficult for organic films that have many overlapping absorption peaks). The user must also choose starting parameters sufficiently close to the final values so that the regression fit converges. Weak absorptions can be difficult to identify when they overlap with strong absorption features, or they can be obscured when there are large interference oscillations in the spectroscopic ellipsometry data. The B-spline function’s flexibility allows the user to model the infrared, dielectric-function line shape for any material, and it requires far less user input and judgment to obtain the dielectric function of a material. The user must simply define the spacing of control nodes, which can usually be obtained from a reference dielectric function or by a preliminary fit to a spectral region where the material is transparent. A “wavelength-range-expansion” fit can then be used to obtain the dielectric function for the remaining spectral range.
- 18 December 2019
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 38 (1) , 014001
Application of a B-spline model dielectric function to infrared spectroscopic ellipsometry data analysis
The flexibility of the Kramers–Kronig-consistent basis spline (B-spline) function provides advantages over traditional physics-based oscillator functions for analyzing infrared spectroscopic ellipsometry data. Oscillator functions require that the user identify the spectral location of every absorption, choose the correct oscillator line shape, and choose the correct number of oscillators (which can be difficult for organic films that have many overlapping absorption peaks). The user must also choose starting parameters sufficiently close to the final values so that the regression fit converges. Weak absorptions can be difficult to identify when they overlap with strong absorption features, or they can be obscured when there are large interference oscillations in the spectroscopic ellipsometry data. The B-spline function’s flexibility allows the user to model the infrared, dielectric-function line shape for any material, and it requires far less user input and judgment to obtain the dielectric function of a material. The user must simply define the spacing of control nodes, which can usually be obtained from a reference dielectric function or by a preliminary fit to a spectral region where the material is transparent. A “wavelength-range-expansion” fit can then be used to obtain the dielectric function for the remaining spectral range.
- 5 July 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (14) , 18545-18562
Extremely broadband ultralight thermally-emissive optical coatings
We report the design, fabrication, and characterization of ultralight highly emissive structures with a record-low mass per area that emit thermal radiation efficiently over a broad spectral (2 to 30 microns) and angular (0–60°) range. The structures comprise one to three pairs of alternating metallic and dielectric thin films and have measured effective 300 K hemispherical emissivity of 0.7 to 0.9 (inferred from angular measurements which cover a bandwidth corresponding to 88% of 300K blackbody power). To our knowledge, these micron-scale-thickness structures, are the lightest reported optical coatings with comparable infrared emissivity. The superior optical properties, together with their mechanical flexibility, low outgassing, and low areal mass, suggest that these coatings are candidates for thermal management in applications demanding of ultralight flexible structures, including aerospace applications, ultralight photovoltaics, lightweight flexible electronics, and textiles for thermal insulation.
- 5 July 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (14) , 18545-18562
Extremely broadband ultralight thermally-emissive optical coatings
We report the design, fabrication, and characterization of ultralight highly emissive structures with a record-low mass per area that emit thermal radiation efficiently over a broad spectral (2 to 30 microns) and angular (0–60°) range. The structures comprise one to three pairs of alternating metallic and dielectric thin films and have measured effective 300 K hemispherical emissivity of 0.7 to 0.9 (inferred from angular measurements which cover a bandwidth corresponding to 88% of 300K blackbody power). To our knowledge, these micron-scale-thickness structures, are the lightest reported optical coatings with comparable infrared emissivity. The superior optical properties, together with their mechanical flexibility, low outgassing, and low areal mass, suggest that these coatings are candidates for thermal management in applications demanding of ultralight flexible structures, including aerospace applications, ultralight photovoltaics, lightweight flexible electronics, and textiles for thermal insulation.
- 15 April 2009
- Published by American Physical Society (APS) in Physical Review B
- Vol. 79 (14) , 144414
Ellipsometric study of the electronic band structure ofacross the ferromagnetic transitionThe optical properties of half-metallic at temperatures below, at, and above the Curie temperature are studied by means of variable angle spectroscopic ellipsometry. The films were epitaxially grown on (100)- and (110)-oriented substrates by chemical vapor deposition. Optical conductivity data reveal a pronounced anisotropy of the optical constants for all films which is in good agreement with what is known about their crystal structure. The main features of the conductivity spectra in the ferromagnetic state are consistent with existing band-structure calculations. However, no temperature dependence of these features across the ferromagnetic transition is evident, posing questions about the electronic structure of the material.- 15 April 2009
- Published by American Physical Society (APS) in Physical Review B
- Vol. 79 (14) , 144414
Ellipsometric study of the electronic band structure ofacross the ferromagnetic transitionThe optical properties of half-metallic at temperatures below, at, and above the Curie temperature are studied by means of variable angle spectroscopic ellipsometry. The films were epitaxially grown on (100)- and (110)-oriented substrates by chemical vapor deposition. Optical conductivity data reveal a pronounced anisotropy of the optical constants for all films which is in good agreement with what is known about their crystal structure. The main features of the conductivity spectra in the ferromagnetic state are consistent with existing band-structure calculations. However, no temperature dependence of these features across the ferromagnetic transition is evident, posing questions about the electronic structure of the material.- 1 January 2009
- Published by Springer Nature in MRS Proceedings
- Vol. 1153
Infrared Ellipsometry Investigation of Hydrogenated Amorphous Silicon
- 1 January 2009
- Published by Springer Nature in MRS Proceedings
- Vol. 1153
Infrared Ellipsometry Investigation of Hydrogenated Amorphous Silicon
- 1 January 2008
- Published by Springer Nature in MRS Proceedings
- Vol. 1146
Monitoring Organic Thin Film Growth In Aqueous Solution In-situ With A Combined Quartz Crystal Microbalance and Ellipsometry
- 1 January 2008
- Published by Springer Nature in MRS Proceedings
- Vol. 1146
Monitoring Organic Thin Film Growth In Aqueous Solution In-situ With A Combined Quartz Crystal Microbalance and Ellipsometry
- 23 June 2006
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 24 (4) , 1605-1609
Measuring the thickness of organic/polymer/biological films on glass substrates using spectroscopic ellipsometry
In this work we discuss a method of determining film thickness for film/substrate combination where the index of refraction of the film and substrate in the transparent spectral regions is almost identical. Common examples of this situation are organic/polymer/biological films on glass substrates. Infrared ellipsometry is used and we use weight gain to provide some necessary additional information for determining the optical functions for the film material. The spectral regions of strong molecular vibrations are then used for determining film thickness.
- 23 June 2006
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 24 (4) , 1605-1609
Measuring the thickness of organic/polymer/biological films on glass substrates using spectroscopic ellipsometry
In this work we discuss a method of determining film thickness for film/substrate combination where the index of refraction of the film and substrate in the transparent spectral regions is almost identical. Common examples of this situation are organic/polymer/biological films on glass substrates. Infrared ellipsometry is used and we use weight gain to provide some necessary additional information for determining the optical functions for the film material. The spectral regions of strong molecular vibrations are then used for determining film thickness.