Willy Kunz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Willy Kunz has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Alexander Michaelis
1 shared publication- Andrea Franke
AXIAL Ingenieurgesellschaft für Maschinenbau mbH, 01445 Radebeul, Germany
1 shared publication - Benjamin Braun
Space Structures GmbH, 12435 Berlin, Germany
1 shared publication - Christoph Leyens
TU Dresden
1 shared publication - Elena López
Fraunhofer Institute for Material and Beam Technology IWS, 01277 Dresden, Germany
1 shared publication - Frank Brückner
Fraunhofer Institute for Material and Beam Technology IWS
1 shared publication
Latest Publications
- Open Access
Development of a System for Additive Manufacturing of Ceramic Matrix Composite Structures Using Laser Technology
Ceramic matrix composites (CMCs) are refractory ceramic materials with damage-tolerant behavior. Coming from the space industry, this class of materials is increasingly being used in other applications, such as automotive construction for high-performance brake discs, furnace technology, heat coatings for pipe systems and landing flaps on reusable rocket sections. In order to produce CMC faster and more cost-efficiently for the increasing demand, a new additive manufacturing process is being tested, which in the future should also be able to realize material joints and higher component wall thicknesses than conventional processes. The main features of the process are as follows. A ceramic fiber bundle is de-sized and infiltrated with ceramic suspension. The bundle infiltrated with matrix material is dried and then applied to a body form. During application, the matrix material is melted by laser radiation without damaging the fiber material. For the initial validation of the material system, samples are pressed and analyzed for their absorption properties using integrating sphere measurement. With the results, a suitable processing laser is selected, and initial melting tests of the matrix system are carried out. After the first validation of the process, a test system is set up, and the first test specimens are produced to determine the material parameters.
Open AccessDevelopment of a System for Additive Manufacturing of Ceramic Matrix Composite Structures Using Laser Technology
Ceramic matrix composites (CMCs) are refractory ceramic materials with damage-tolerant behavior. Coming from the space industry, this class of materials is increasingly being used in other applications, such as automotive construction for high-performance brake discs, furnace technology, heat coatings for pipe systems and landing flaps on reusable rocket sections. In order to produce CMC faster and more cost-efficiently for the increasing demand, a new additive manufacturing process is being tested, which in the future should also be able to realize material joints and higher component wall thicknesses than conventional processes. The main features of the process are as follows. A ceramic fiber bundle is de-sized and infiltrated with ceramic suspension. The bundle infiltrated with matrix material is dried and then applied to a body form. During application, the matrix material is melted by laser radiation without damaging the fiber material. For the initial validation of the material system, samples are pressed and analyzed for their absorption properties using integrating sphere measurement. With the results, a suitable processing laser is selected, and initial melting tests of the matrix system are carried out. After the first validation of the process, a test system is set up, and the first test specimens are produced to determine the material parameters.
- 1 December 2020
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 40 (15) , 5740-5748
Crack-healing in ytterbium silicate filled with silicon carbide particles
- 1 December 2020
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 40 (15) , 5740-5748
Crack-healing in ytterbium silicate filled with silicon carbide particles
- Open Access
Delayed Formation of Thermally Grown Oxide in Environmental Barrier Coatings for Non-Oxide Ceramic Matrix Composites
The oxidation and corrosion behavior at elevated temperatures of a SiCF/SiC(N) composite with two plasma-sprayed environmental barrier coating (EBC) systems were studied. After both processes, the formation of a silica-based thermally grown oxide (TGO) layer was observed. The formation of this TGO caused two principal failure mechanisms of the EBC. Firstly, spallation of the EBC induced by stresses from volume expansion and phase transformation to crystalline SiO2 was observed. Water vapor corrosion of the TGO with gap formation in the top region of the TGO was found to be a second failure mechanism. After a burner rig test of the Al2O3-YAG EBC system, this corrosion process was observed at the TGO surface and in the volume of the Al2O3 bond coat. In the case of the second system, Si-Yb2Si2O7/SiC-Yb2SiO5, the formation of the TGO could be delayed by introducing an additional intermediate layer based on Yb2Si2O7 filled with SiC particles. The SiC particles in the intermediate layer were oxidized and served as getter to reduce the permeation of oxidants (O2, H2O) into the material. In this way, the formation of the TGO and the failure mechanisms caused by their formation and growth could be delayed.
Open AccessDelayed Formation of Thermally Grown Oxide in Environmental Barrier Coatings for Non-Oxide Ceramic Matrix Composites
The oxidation and corrosion behavior at elevated temperatures of a SiCF/SiC(N) composite with two plasma-sprayed environmental barrier coating (EBC) systems were studied. After both processes, the formation of a silica-based thermally grown oxide (TGO) layer was observed. The formation of this TGO caused two principal failure mechanisms of the EBC. Firstly, spallation of the EBC induced by stresses from volume expansion and phase transformation to crystalline SiO2 was observed. Water vapor corrosion of the TGO with gap formation in the top region of the TGO was found to be a second failure mechanism. After a burner rig test of the Al2O3-YAG EBC system, this corrosion process was observed at the TGO surface and in the volume of the Al2O3 bond coat. In the case of the second system, Si-Yb2Si2O7/SiC-Yb2SiO5, the formation of the TGO could be delayed by introducing an additional intermediate layer based on Yb2Si2O7 filled with SiC particles. The SiC particles in the intermediate layer were oxidized and served as getter to reduce the permeation of oxidants (O2, H2O) into the material. In this way, the formation of the TGO and the failure mechanisms caused by their formation and growth could be delayed.
- 1 August 2015
- Published by Springer Nature in Keramische Zeitschrift
- Vol. 67 (4) , 225-226
Entwicklung eines Siliziumnitrid-Werkstoffes für Rotoren in Mikrogasturbinen
- 1 August 2015
- Published by Springer Nature in Keramische Zeitschrift
- Vol. 67 (4) , 225-226
Entwicklung eines Siliziumnitrid-Werkstoffes für Rotoren in Mikrogasturbinen