Richard Floyd
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Richard Floyd has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
Grigory Simin
Department of Electrical Engineering, University of South Carolina, Columbia, SC 29208, United States of America
6 shared publicationsAsif Khan
Department of Electrical Engineering, University of South Carolina, Columbia, SC 29208, United States of America
5 shared publicationsMvs Chandrashekhar
Department of Electrical Engineering, University of South Carolina, Columbia, SC 29208, United States of America
5 shared publicationsAbdullah Mamun
Department of Electrical Engineering, University of South Carolina, Columbia, SC 29208, United States of America
4 shared publications- Andrew T. Binder
Sandia National Laboratories
4 shared publications Kamal Hussain
Department of Electrical Engineering, University of South Carolina, Columbia, SC 29208, United States of America
4 shared publications
Latest Publications
- 28 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (12) , 6906-6911
Static Electrothermal Study of >3 kV Co-Packaged MOSFETs and Monolithic BiDFETs
We report a comparison of the static electrothermal performance of SiC co-packaged MOSFETs and a monolithic bi-directional field effect transistor (BiDFET) fabricated in a commercial foundry from the same wafer. Both bi-directional switching solutions provide fully gate-controlled output characteristics in the first and third quadrants of operation, a specific on-resistance of ~50m $\Omega \cdot $ cm2 at room temperature, and a breakdown voltage that exceeds 3 kV. We demonstrate accurate extraction and monitoring of the junction temperature using variations in the on-resistance and validate this assertion through theoretical and experimental evidence. Our investigation reveals that the static electrical performance is identical and indicates the difference in thermal performance between the two bi-directional switching solutions is solely attributed to the arrangement of the chips within the package (i.e., an increased power density locally thermally saturates the package) instead of a fundamental property of the device architecture. To verify this, we present the results of an analytical heat flow model, which confirms that the increased rate of self-heating for the monolithically integrated BiDFET compared to two co-packaged MOSFETs is due to the increased heat flux density and limitation of the packaging thermals. This work demonstrates that the proximity of devices inherent to compact bi-directional SiC switches can lead to excessive device heating during extended states of conduction, emphasizing the need for advanced packaging.
- 28 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (12) , 6906-6911
Static Electrothermal Study of >3 kV Co-Packaged MOSFETs and Monolithic BiDFETs
We report a comparison of the static electrothermal performance of SiC co-packaged MOSFETs and a monolithic bi-directional field effect transistor (BiDFET) fabricated in a commercial foundry from the same wafer. Both bi-directional switching solutions provide fully gate-controlled output characteristics in the first and third quadrants of operation, a specific on-resistance of ~50m $\Omega \cdot $ cm2 at room temperature, and a breakdown voltage that exceeds 3 kV. We demonstrate accurate extraction and monitoring of the junction temperature using variations in the on-resistance and validate this assertion through theoretical and experimental evidence. Our investigation reveals that the static electrical performance is identical and indicates the difference in thermal performance between the two bi-directional switching solutions is solely attributed to the arrangement of the chips within the package (i.e., an increased power density locally thermally saturates the package) instead of a fundamental property of the device architecture. To verify this, we present the results of an analytical heat flow model, which confirms that the increased rate of self-heating for the monolithically integrated BiDFET compared to two co-packaged MOSFETs is due to the increased heat flux density and limitation of the packaging thermals. This work demonstrates that the proximity of devices inherent to compact bi-directional SiC switches can lead to excessive device heating during extended states of conduction, emphasizing the need for advanced packaging.
- Open Access
- 1 October 2025
- Published by Office of Scientific and Technical Information (OSTI)
AC to AC Solid State Transformer with Bidirectional Switches
This report details the work of the 3-year project for the AC-to-AC Solid State Transformer with Bidirectional Switches project devoted to developing and demonstrated a Type I Solid State Transformer. This report details the design, fabrication, and evaluation of both three-phase and single-phase versions of this solid state transformer operating as a single module, modules in parallel, and modules in cascade. Additionally, this report details the fabrication and evaluation of custom Silicon C
- 1 October 2025
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessAC to AC Solid State Transformer with Bidirectional Switches
This report details the work of the 3-year project for the AC-to-AC Solid State Transformer with Bidirectional Switches project devoted to developing and demonstrated a Type I Solid State Transformer. This report details the design, fabrication, and evaluation of both three-phase and single-phase versions of this solid state transformer operating as a single module, modules in parallel, and modules in cascade. Additionally, this report details the fabrication and evaluation of custom Silicon C
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (35) , 1679
(Invited) Advanced Design Concepts for Vertical Gallium Nitride MOSFETs
Wide-bandgap semiconductors have a significant advantage over conventional Si-based electronics by leveraging materials properties to achieve higher breakdown voltage, lower on-resistance, and high-frequency operation. Gallium nitride (GaN) is of interest for vertical device architectures but directly competes with the already established silicon carbide (SiC) power devices. In the case of vertical GaN rectifiers which are unipolar figure-of-merit limited, the materials advantage of GaN provides a modest gain in terms of critical electric field and very slight gains in bulk mobility and saturation velocity, while being at a disadvantage in terms of thermal conductivity compared to SiC. However, despite still being a very immature technology, vertical GaN MOSFETs have demonstrated channel mobilities upwards of 200 cm2/V·s, over three times that of SiC-based MOSFETs. For 1200V-class devices, channel mobility directly contributes to a significant portion of device on-resistance, and it is therefore expected that vertical GaN MOSFETs would offer a substantial performance advantage compared to SiC MOSFETs. Despite this, the development of vertical GaN devices that demonstrate this theoretical potential faces many challenges. Several fundamental limitations exist within the manufacturing process that prohibit GaN devices from directly mirroring the design rules for similar SiC devices. In this talk, we will discuss several key design concepts recently developed for vertical GaN MOSFETs which serve to address several critical issues for GaN. Limitations in selective-area doping for GaN provide an additional challenge in designing edge termination structures, advanced features that protect the gate dielectric during the blocking state, and provides restrictions on minimizing cell pitch. Proper edge termination design is required to reach an avalanche voltage near the theoretical limit and avoid early breakdown. We present an optimized design point for the edge termination with a good match between theoretical and experimental data using a step-etched junction termination extension. Despite a well-designed edge termination, early breakdown will occur in the gate dielectric at the bottom of the gate trench due to field crowding in the dielectric at high blocking voltages. We propose a new method for protecting the gate dielectric by means of a buried field shield formed by an etch-and-regrowth process. Experimental data shows this gate dielectric failure can occur as early as 1/3rd of the designed blocking voltage. The field shield design is shown in simulation to sufficiently reduce the electric field in the gate dielectric to below 4 MV/cm with minimal or no derating of the device depending on geometry of the shield. Additional methods will be presented on new techniques to minimize cell pitch, a critical factor necessary to compete against SiC. Cell pitch minimization not only reduces on-resistance and gate-charge trade-offs, but it is also a driving factor to reduce cost and increase die density on wafer. Finally, techniques have been developed for advanced metal contact designs specific to the trench MOSFET, which further aid in reducing cell pitch. This work was supported by the Electric Drivetrain Consortium managed by Susan Rogers of DOE’s Vehicle Technologies Office. Sandia National Laboratories is a multi-mission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525. This paper describes objective technical results and analysis. Any subjective views or opinions that might be expressed in the paper do not necessarily represent the views of the U.S. Department of Energy or the United States Government.
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (35) , 1679
(Invited) Advanced Design Concepts for Vertical Gallium Nitride MOSFETs
Wide-bandgap semiconductors have a significant advantage over conventional Si-based electronics by leveraging materials properties to achieve higher breakdown voltage, lower on-resistance, and high-frequency operation. Gallium nitride (GaN) is of interest for vertical device architectures but directly competes with the already established silicon carbide (SiC) power devices. In the case of vertical GaN rectifiers which are unipolar figure-of-merit limited, the materials advantage of GaN provides a modest gain in terms of critical electric field and very slight gains in bulk mobility and saturation velocity, while being at a disadvantage in terms of thermal conductivity compared to SiC. However, despite still being a very immature technology, vertical GaN MOSFETs have demonstrated channel mobilities upwards of 200 cm2/V·s, over three times that of SiC-based MOSFETs. For 1200V-class devices, channel mobility directly contributes to a significant portion of device on-resistance, and it is therefore expected that vertical GaN MOSFETs would offer a substantial performance advantage compared to SiC MOSFETs. Despite this, the development of vertical GaN devices that demonstrate this theoretical potential faces many challenges. Several fundamental limitations exist within the manufacturing process that prohibit GaN devices from directly mirroring the design rules for similar SiC devices. In this talk, we will discuss several key design concepts recently developed for vertical GaN MOSFETs which serve to address several critical issues for GaN. Limitations in selective-area doping for GaN provide an additional challenge in designing edge termination structures, advanced features that protect the gate dielectric during the blocking state, and provides restrictions on minimizing cell pitch. Proper edge termination design is required to reach an avalanche voltage near the theoretical limit and avoid early breakdown. We present an optimized design point for the edge termination with a good match between theoretical and experimental data using a step-etched junction termination extension. Despite a well-designed edge termination, early breakdown will occur in the gate dielectric at the bottom of the gate trench due to field crowding in the dielectric at high blocking voltages. We propose a new method for protecting the gate dielectric by means of a buried field shield formed by an etch-and-regrowth process. Experimental data shows this gate dielectric failure can occur as early as 1/3rd of the designed blocking voltage. The field shield design is shown in simulation to sufficiently reduce the electric field in the gate dielectric to below 4 MV/cm with minimal or no derating of the device depending on geometry of the shield. Additional methods will be presented on new techniques to minimize cell pitch, a critical factor necessary to compete against SiC. Cell pitch minimization not only reduces on-resistance and gate-charge trade-offs, but it is also a driving factor to reduce cost and increase die density on wafer. Finally, techniques have been developed for advanced metal contact designs specific to the trench MOSFET, which further aid in reducing cell pitch. This work was supported by the Electric Drivetrain Consortium managed by Susan Rogers of DOE’s Vehicle Technologies Office. Sandia National Laboratories is a multi-mission laboratory managed and operated by National Technology & Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA0003525. This paper describes objective technical results and analysis. Any subjective views or opinions that might be expressed in the paper do not necessarily represent the views of the U.S. Department of Energy or the United States Government.
- Open Access
- 25 July 2023
- Published by Elsevier in e-Prime - Advances in Electrical Engineering, Electronics and Energy
- Vol. 5
Gate protection for vertical gallium nitride trench MOSFETs: The buried field shield
- 25 July 2023
- Published by Elsevier in e-Prime - Advances in Electrical Engineering, Electronics and Energy
- Vol. 5
Open AccessGate protection for vertical gallium nitride trench MOSFETs: The buried field shield
- Open Access
- 1 June 2023
- Published by IOP Publishing in Applied Physics Express
- Vol. 16 (6) , 061001
Al0.64Ga0.36N channel MOSHFET on single crystal bulk AlN substrate
We report MOCVD-grown Al0.87Ga0.13N/Al0.64Ga0.36N metal-oxide-semiconductor-heterojunction-field-effect-transistors on single crystal bulk AlN substrate. As compared to control devices on AlN template, thermal impedance for devices on single crystal AlN decreased to 1/3 from 31 to 10 K mm W−1, comparable to SiC and copper heat-sinks. This represents a significant thermo-electric co-design advantage over other semiconductors. As a result, the peak drain saturation current increased from 410 to 610 mAmm−1. A 3-terminal breakdown field of 3.7 MV cm−1 was measured, which to date represents state-of-the-art performance for devices with similar Al x Ga1−x N-channel composition. This translates to a measured Baliga figure of merit of 460 MWcm−2.
- 1 June 2023
- Published by IOP Publishing in Applied Physics Express
- Vol. 16 (6) , 061001
Open AccessAl0.64Ga0.36N channel MOSHFET on single crystal bulk AlN substrate
We report MOCVD-grown Al0.87Ga0.13N/Al0.64Ga0.36N metal-oxide-semiconductor-heterojunction-field-effect-transistors on single crystal bulk AlN substrate. As compared to control devices on AlN template, thermal impedance for devices on single crystal AlN decreased to 1/3 from 31 to 10 K mm W−1, comparable to SiC and copper heat-sinks. This represents a significant thermo-electric co-design advantage over other semiconductors. As a result, the peak drain saturation current increased from 410 to 610 mAmm−1. A 3-terminal breakdown field of 3.7 MV cm−1 was measured, which to date represents state-of-the-art performance for devices with similar Al x Ga1−x N-channel composition. This translates to a measured Baliga figure of merit of 460 MWcm−2.
- Open Access
- 1 January 2023
- Published by IOP Publishing in Applied Physics Express
- Vol. 16 (1) , 014005
High figure of merit extreme bandgap Al0.87Ga0.13N-Al0.64Ga0.36N heterostructures over bulk AlN substrates
We report on high-quality n-Al0.87Ga0.13N-A0.64Ga0.36N heterostructures over single crystal AlN. For these pseudomorphic heterostructures, high-resolution X-ray and X-ray Topographic analysis was used to establish a threading dislocation density of 7 × 103 cm−2. Using reverse composition graded n+-Al x Ga1-x N contact layers, we obtained linear ohmic contacts with 4.3 Ω mm specific resistance. A critical breakdown field >11 MV cm−1 was also measured. In combination with the channel resistance of 2400 Ω sq−1, these translate to a Baliga’s Figure of Merit of 2.27 GW cm−2. This, to the best of our knowledge is the highest reported value for extreme bandgap AlGaN heterostructures.
- 1 January 2023
- Published by IOP Publishing in Applied Physics Express
- Vol. 16 (1) , 014005
Open AccessHigh figure of merit extreme bandgap Al0.87Ga0.13N-Al0.64Ga0.36N heterostructures over bulk AlN substrates
We report on high-quality n-Al0.87Ga0.13N-A0.64Ga0.36N heterostructures over single crystal AlN. For these pseudomorphic heterostructures, high-resolution X-ray and X-ray Topographic analysis was used to establish a threading dislocation density of 7 × 103 cm−2. Using reverse composition graded n+-Al x Ga1-x N contact layers, we obtained linear ohmic contacts with 4.3 Ω mm specific resistance. A critical breakdown field >11 MV cm−1 was also measured. In combination with the channel resistance of 2400 Ω sq−1, these translate to a Baliga’s Figure of Merit of 2.27 GW cm−2. This, to the best of our knowledge is the highest reported value for extreme bandgap AlGaN heterostructures.
- 27 September 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (13) , 132106
Excimer laser liftoff of AlGaN/GaN HEMTs on thick AlN heat spreaders
We report on 193 nm excimer laser-based liftoff (LLO) of Al0.26Ga0.74N/GaN high electron mobility transistors (HEMTs) with thick (t > 10 μm) AlN heat spreading buffer layers grown over sapphire substrates. The use of the thick AlN heat spreading layer resulted in thermal resistance ( ) of 16 K mm/W for as-fabricated devices on sapphire, which is lower than the value of ∼25–50 K mm/W for standard HEMT structures on sapphire without the heat-spreaders. Soldering the LLO devices onto a copper heat sink led to a further reduction of to 8 K mm/W, a value comparable to published measurements on bulk SiC substrates. The reduction in by LLO and bonding to copper led to significantly reduced self-heating and drain current droop. A drain current density as high as 0.9 A/mm was observed despite a marginal reduction of the carrier mobility (∼1800 to ∼1500 cm2/V s). This is the highest drain current density and mobility reported to-date for LLO AlGaN/GaN HEMTs.- 27 September 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (13) , 132106
Excimer laser liftoff of AlGaN/GaN HEMTs on thick AlN heat spreaders
We report on 193 nm excimer laser-based liftoff (LLO) of Al0.26Ga0.74N/GaN high electron mobility transistors (HEMTs) with thick (t > 10 μm) AlN heat spreading buffer layers grown over sapphire substrates. The use of the thick AlN heat spreading layer resulted in thermal resistance ( ) of 16 K mm/W for as-fabricated devices on sapphire, which is lower than the value of ∼25–50 K mm/W for standard HEMT structures on sapphire without the heat-spreaders. Soldering the LLO devices onto a copper heat sink led to a further reduction of to 8 K mm/W, a value comparable to published measurements on bulk SiC substrates. The reduction in by LLO and bonding to copper led to significantly reduced self-heating and drain current droop. A drain current density as high as 0.9 A/mm was observed despite a marginal reduction of the carrier mobility (∼1800 to ∼1500 cm2/V s). This is the highest drain current density and mobility reported to-date for LLO AlGaN/GaN HEMTs.- 15 July 2021
- Published by IOP Publishing in Applied Physics Express
- Vol. 14 (8) , 084002
Enhanced light extraction efficiency of micropixel geometry AlGaN DUV light-emitting diodes
- 15 July 2021
- Published by IOP Publishing in Applied Physics Express
- Vol. 14 (8) , 084002
Enhanced light extraction efficiency of micropixel geometry AlGaN DUV light-emitting diodes
- 17 December 2020
- Published by IOP Publishing in Applied Physics Express
- Vol. 14 (1) , 014002
An opto-thermal study of high brightness 280 nm emission AlGaN micropixel light-emitting diode arrays
We present a study of the light output power and the thermal impedance of 281 nm emission AlGaN based micropixel LEDs. A modular interconnected micropixel array design is presented which enables dense packing with area and power scalability. We study 5–15 μm diameter stand-alone devices and parallel-connected micropixel arrays with 5 μm interpixel gaps. A standalone 5 μm pixel emits 291 W cm−2 at 10.2 kA cm−2 DC-drive. A power as high as 23 mW (361 W cm−2) was measured at a pulsed-pump current of 800 mA (∼15 kA cm−2) for an interconnected array. These are the smallest and brightest DUV LEDs to date.
- 17 December 2020
- Published by IOP Publishing in Applied Physics Express
- Vol. 14 (1) , 014002
An opto-thermal study of high brightness 280 nm emission AlGaN micropixel light-emitting diode arrays
We present a study of the light output power and the thermal impedance of 281 nm emission AlGaN based micropixel LEDs. A modular interconnected micropixel array design is presented which enables dense packing with area and power scalability. We study 5–15 μm diameter stand-alone devices and parallel-connected micropixel arrays with 5 μm interpixel gaps. A standalone 5 μm pixel emits 291 W cm−2 at 10.2 kA cm−2 DC-drive. A power as high as 23 mW (361 W cm−2) was measured at a pulsed-pump current of 800 mA (∼15 kA cm−2) for an interconnected array. These are the smallest and brightest DUV LEDs to date.
- Open Access
- 8 January 2020
- Published by IOP Publishing in Applied Physics Express
- Vol. 13 (2) , 022003
Photonics integrated circuits using Al x Ga1−x N based UVC light-emitting diodes, photodetectors and waveguides
- 8 January 2020
- Published by IOP Publishing in Applied Physics Express
- Vol. 13 (2) , 022003
Open AccessPhotonics integrated circuits using Al x Ga1−x N based UVC light-emitting diodes, photodetectors and waveguides