Xiaoming Guo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Xiaoming Guo has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
Nana Zhang
5 shared publicationsHao Wang
Southeast University
3 shared publicationsXiaoqiang Yan
3 shared publications- Xiaoxiao Sun
Jiangsu Key Laboratory of Engineering Mechanics, Department of Engineering Mechanics, Southeast University, Nanjing, China
3 shared publications - Jichang Wang
Jiangsu Key Laboratory of Engineering Mechanics, Department of Engineering Mechanics, School of Civil Engineering, Southeast University, Nanjing, China
2 shared publications - Luo Sen2 shared publications
Latest Publications
- Open Access
- 3 September 2026
- Published by Elsevier in SSRN Electronic Journal
Effects of fiber content and notch eccentricity on the fracture behavior of UHPSFRC
To investigate the fracture behavior of ultra-high performance steel fiber reinforced concrete (UHPSFRC) three-point bending beams, three-point bending tests were conducted. Combined with digital image correlation (DIC) and numerical simulation, the influence mechanisms and strengthening effects on the fracture behavior were explored. The DIC measurements reveal obvious strain concentration in the longitudinal strain field on the specimen surface; as the external load increases, a macro-crack initiates at the precast notch, manifesting as a discontinuity in the horizontal displacement field. Numerical simulations with different fiber contents show that fibers bridge the crack faces and drive stress redistribution within the fiber network, which suppresses local damage accumulation, delays stiffness degradation, and improves post-peak load-bearing stability. Based on the double-K fracture criterion, calculation formulae for the initiation and unstable fracture toughness of UHPSFRC were established, demonstrating that even a low content of steel fibers can significantly enhance the unstable toughness. In addition, simulations under different notch eccentricities show that the crack gradually bends toward the loading point during propagation, forming a mixed mode-I/II crack. This study reveals the governing roles of fiber content and notch position in the fracture behavior of UHPSFRC, providing a basis for numerical modeling optimization and engineering design.
- 3 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffects of fiber content and notch eccentricity on the fracture behavior of UHPSFRC
To investigate the fracture behavior of ultra-high performance steel fiber reinforced concrete (UHPSFRC) three-point bending beams, three-point bending tests were conducted. Combined with digital image correlation (DIC) and numerical simulation, the influence mechanisms and strengthening effects on the fracture behavior were explored. The DIC measurements reveal obvious strain concentration in the longitudinal strain field on the specimen surface; as the external load increases, a macro-crack initiates at the precast notch, manifesting as a discontinuity in the horizontal displacement field. Numerical simulations with different fiber contents show that fibers bridge the crack faces and drive stress redistribution within the fiber network, which suppresses local damage accumulation, delays stiffness degradation, and improves post-peak load-bearing stability. Based on the double-K fracture criterion, calculation formulae for the initiation and unstable fracture toughness of UHPSFRC were established, demonstrating that even a low content of steel fibers can significantly enhance the unstable toughness. In addition, simulations under different notch eccentricities show that the crack gradually bends toward the loading point during propagation, forming a mixed mode-I/II crack. This study reveals the governing roles of fiber content and notch position in the fracture behavior of UHPSFRC, providing a basis for numerical modeling optimization and engineering design.
- 20 November 2025
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 202
A phase field approach for fiber-reinforced composites incorporating the LaRC03 failure criterion
- 20 November 2025
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 202
A phase field approach for fiber-reinforced composites incorporating the LaRC03 failure criterion
- 18 November 2025
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 45 (17-18) , 4046-4059
Mechanical behavior and damage mechanism of foldcore sandwich structures with different fiber layup directions
Foldcore sandwich structures have gained attention for impact-resistant applications due to their high specific mechanical performance and low density. However, their anisotropy, resulting from unidirectional fiber reinforcement, leads to complex mechanical behavior. The combined effect of fiber orientation and core thickness on bending–compression response and failure evolution remains insufficiently characterized. In this study, carbon fiber prepreg foldcore panels were fabricated, and two orthogonal fiber orientations (L and W) as well as core thicknesses (single and double layers) were examined through three-point bending, out-of-plane compression, and post-bending compression tests. A simplified Abaqus model was also developed to support the experimental analysis. Panels with fibers aligned in the L-direction demonstrating superior flexural toughness and delayed failure. Increasing core thickness significantly enhanced bending performance, while its effect on compressive behavior was minimal. Furthermore, post-bending compression tests reveal that even after partial delamination, foldcore structures retain significant compressive strength, indicating their high toughness and structural stability. Numerical simulations confirmed that failure initiates at the core center, with matrix compression dominating for the W orientation and matrix tension for the L orientation.
- 18 November 2025
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 45 (17-18) , 4046-4059
Mechanical behavior and damage mechanism of foldcore sandwich structures with different fiber layup directions
Foldcore sandwich structures have gained attention for impact-resistant applications due to their high specific mechanical performance and low density. However, their anisotropy, resulting from unidirectional fiber reinforcement, leads to complex mechanical behavior. The combined effect of fiber orientation and core thickness on bending–compression response and failure evolution remains insufficiently characterized. In this study, carbon fiber prepreg foldcore panels were fabricated, and two orthogonal fiber orientations (L and W) as well as core thicknesses (single and double layers) were examined through three-point bending, out-of-plane compression, and post-bending compression tests. A simplified Abaqus model was also developed to support the experimental analysis. Panels with fibers aligned in the L-direction demonstrating superior flexural toughness and delayed failure. Increasing core thickness significantly enhanced bending performance, while its effect on compressive behavior was minimal. Furthermore, post-bending compression tests reveal that even after partial delamination, foldcore structures retain significant compressive strength, indicating their high toughness and structural stability. Numerical simulations confirmed that failure initiates at the core center, with matrix compression dominating for the W orientation and matrix tension for the L orientation.
- 3 August 2024
- Published by Elsevier in Composite Structures
- Vol. 346
Anisotropic mechanical behavior and failure of foldcore structures of fibre-reinforced composites under impact loading
- 3 August 2024
- Published by Elsevier in Composite Structures
- Vol. 346
Anisotropic mechanical behavior and failure of foldcore structures of fibre-reinforced composites under impact loading
- 9 April 2024
- Published by Elsevier in Journal of Wind Engineering and Industrial Aerodynamics
- Vol. 248, 105712
Field monitoring and control for vortex-induced vibration of hanger cables in suspension bridge
- 9 April 2024
- Published by Elsevier in Journal of Wind Engineering and Industrial Aerodynamics
- Vol. 248, 105712
Field monitoring and control for vortex-induced vibration of hanger cables in suspension bridge
- 1 February 2022
- Published by Zhejiang University Press in Journal of Zhejiang University-SCIENCE A
- Vol. 23 (2) , 118-139
A novel multi-level model for quasi-brittle cracking analysis with complex microstructure
The paper presents a novel multi-level model for quasi-brittle cracking analysis. Based on the partition of unity and information transmission technology,
- 1 February 2022
- Published by Zhejiang University Press in Journal of Zhejiang University-SCIENCE A
- Vol. 23 (2) , 118-139
A novel multi-level model for quasi-brittle cracking analysis with complex microstructure
The paper presents a novel multi-level model for quasi-brittle cracking analysis. Based on the partition of unity and information transmission technology,
- 11 June 2021
- Published by Emerald Publishing in Engineering Computations
- Vol. 38 (10) , 3879-3903
The meso-failure mechanism of lightweight concrete simulated by the phase field method
Purpose: A mesoscopic phase field (PF) model is proposed to simulate the meso-failure process of lightweight concrete.Design/methodology/approach: The PF damage model is applied to the meso-failure process of lightweight concrete through the ABAQUS subroutine user-defined element (UEL). And the improved staggered iteration scheme with a one-pass procedure is used to alternately solve the coupling equations.Findings: These examples clearly show that the crack initiation of the lightweight concrete specimens mainly occurs in the ceramsite aggregates with weak strength, especially in the larger aggregates. The crack propagation paths of the specimens with the same volume fraction of light aggregates are completely different, but the crack propagation paths all pass through the ceramsite aggregates near the cracks. The results also showed that with the increase in the volume fractions of the aggregates, the slope and the peak loads of the force-deflection (F-d) curves gradually decrease, the load-bearing capacity of the lightweight concrete specimens decreases, and crack branching and coalescence are less likely during crack propagation.Originality/value: The mesostructures with a mortar matrix, aggregates and an interfacial transition zone (ITZ) are generated by an automatic generation and placement program, thus incorporating the typical three-phase characteristics of lightweight concrete into the PF model.
- 11 June 2021
- Published by Emerald Publishing in Engineering Computations
- Vol. 38 (10) , 3879-3903
The meso-failure mechanism of lightweight concrete simulated by the phase field method
Purpose: A mesoscopic phase field (PF) model is proposed to simulate the meso-failure process of lightweight concrete.Design/methodology/approach: The PF damage model is applied to the meso-failure process of lightweight concrete through the ABAQUS subroutine user-defined element (UEL). And the improved staggered iteration scheme with a one-pass procedure is used to alternately solve the coupling equations.Findings: These examples clearly show that the crack initiation of the lightweight concrete specimens mainly occurs in the ceramsite aggregates with weak strength, especially in the larger aggregates. The crack propagation paths of the specimens with the same volume fraction of light aggregates are completely different, but the crack propagation paths all pass through the ceramsite aggregates near the cracks. The results also showed that with the increase in the volume fractions of the aggregates, the slope and the peak loads of the force-deflection (F-d) curves gradually decrease, the load-bearing capacity of the lightweight concrete specimens decreases, and crack branching and coalescence are less likely during crack propagation.Originality/value: The mesostructures with a mortar matrix, aggregates and an interfacial transition zone (ITZ) are generated by an automatic generation and placement program, thus incorporating the typical three-phase characteristics of lightweight concrete into the PF model.
- 24 March 2021
- Published by SAGE Publications in International Journal of Damage Mechanics
- Vol. 30 (9) , 1377-1399
Study of the progressive failure of concrete by phase field modeling and experiments
In this research, experiments and numerical simulations are employed to research the failure process of concrete. Fracture experiments on three-point bending (TPB) concrete beams with a prefabricated edge notch at the middle of the beam bottom are performed using a modified rigid testing instrument. The characteristics of the crack and section are analyzed, including the crack tensile opening displacement, crack length and width, and crack faces characteristics. Also, the full curves of the force-crack tensile opening displacement (CMOD) and force-deflection of the TPB beams with the prefabricated edge notch after breakage are obtained. The phase field (PF) damage model is applied to the mixed-mode and mode-I failure processes of concrete structures through the ABAQUS subroutine user defined element (UEL). The crack path and the full curves of force-CMOD and force-deflection obtained by numerical calculations are consistent with the experimental results and the calculated results of other researchers. The influences of the mesh sizes, initial lengths, and notched depths on the TPB beam of concrete are also analyzed.
- 24 March 2021
- Published by SAGE Publications in International Journal of Damage Mechanics
- Vol. 30 (9) , 1377-1399
Study of the progressive failure of concrete by phase field modeling and experiments
In this research, experiments and numerical simulations are employed to research the failure process of concrete. Fracture experiments on three-point bending (TPB) concrete beams with a prefabricated edge notch at the middle of the beam bottom are performed using a modified rigid testing instrument. The characteristics of the crack and section are analyzed, including the crack tensile opening displacement, crack length and width, and crack faces characteristics. Also, the full curves of the force-crack tensile opening displacement (CMOD) and force-deflection of the TPB beams with the prefabricated edge notch after breakage are obtained. The phase field (PF) damage model is applied to the mixed-mode and mode-I failure processes of concrete structures through the ABAQUS subroutine user defined element (UEL). The crack path and the full curves of force-CMOD and force-deflection obtained by numerical calculations are consistent with the experimental results and the calculated results of other researchers. The influences of the mesh sizes, initial lengths, and notched depths on the TPB beam of concrete are also analyzed.