Chenghong Duan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chenghong Duan has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Xiangpeng Luo
College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing, China
4 shared publications - Minghuang Zhao
College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing, China
2 shared publications Dazhi Shang
College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, Beijing, China
1 shared publication- Jiayi Li
College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology, North Third Ring Road 15, Chaoyang District, Beijing 100029, China
1 shared publication Minghuang Zhao
Computer Aided Mechanical Engineering Center, Beijing University of Chemical Technology, Beijing, China
1 shared publicationXiangxiang Han
Beijing University of Chemical Technology, Beijing, China
1 shared publication
Latest Publications
- 16 November 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 33 (24) , 13709-13720
Numerical and Experimental Study on the Fatigue Behavior of X80 Steel Treated by Biomimetic Laser Shock Peening
- 16 November 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 33 (24) , 13709-13720
Numerical and Experimental Study on the Fatigue Behavior of X80 Steel Treated by Biomimetic Laser Shock Peening
- 21 December 2021
- Published by Springer Nature in Metals and Materials International
- Vol. 28 (9) , 2225-2238
Heat Transfer, Laser Remelting/Premelting Behavior and Metallurgical Bonding During Selective Laser Melting of Metal Powder
- 21 December 2021
- Published by Springer Nature in Metals and Materials International
- Vol. 28 (9) , 2225-2238
Heat Transfer, Laser Remelting/Premelting Behavior and Metallurgical Bonding During Selective Laser Melting of Metal Powder
- Open Access
Numerical Study on Thermodynamic Behavior during Selective Laser Melting of 24CrNiMo Alloy Steel
In this paper, a multi-layer and multi-track finite element model of 24CrNiMo alloy steel by selective laser melting (SLM) is established by using the ABAQUS software. The distribution and evolution of temperature field and stress field and the influence of process parameters on them are systematically studied. The results show that the peak temperature increases from 2153 °C to 3105 °C and the residual stress increases from 335 MPa to 364 MPa with increasing laser power from 200 W to 300 W; the peak temperature decreases from 2905 °C to 2405 °C and the residual stress increases from 327 MPa to 363 MPa with increasing scanning speed from 150 mm/s to 250 mm/s; the peak temperature increases from 2621 °C to 2914 °C and the residual stress decreases from 354 MPa to 300 MPa with increasing preheating temperature from 25 °C to 400 °C. Far away from scanning area, far away from starting point, and the adjacent areas with vertical scanning direction, resulting in a uniform temperature distribution, help to reduce the residual stress. Due to the remelting effect, the interlayer scanning angle changing helps to release the residual stress of the former layer causing a smaller residual stress after redistribution.
Open AccessNumerical Study on Thermodynamic Behavior during Selective Laser Melting of 24CrNiMo Alloy Steel
In this paper, a multi-layer and multi-track finite element model of 24CrNiMo alloy steel by selective laser melting (SLM) is established by using the ABAQUS software. The distribution and evolution of temperature field and stress field and the influence of process parameters on them are systematically studied. The results show that the peak temperature increases from 2153 °C to 3105 °C and the residual stress increases from 335 MPa to 364 MPa with increasing laser power from 200 W to 300 W; the peak temperature decreases from 2905 °C to 2405 °C and the residual stress increases from 327 MPa to 363 MPa with increasing scanning speed from 150 mm/s to 250 mm/s; the peak temperature increases from 2621 °C to 2914 °C and the residual stress decreases from 354 MPa to 300 MPa with increasing preheating temperature from 25 °C to 400 °C. Far away from scanning area, far away from starting point, and the adjacent areas with vertical scanning direction, resulting in a uniform temperature distribution, help to reduce the residual stress. Due to the remelting effect, the interlayer scanning angle changing helps to release the residual stress of the former layer causing a smaller residual stress after redistribution.
- Open Access
- 1 December 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 677 (3) , 032059
Effects of Initial Crack Defect on Fatigue Crack Growth of Camshaft for Nuclear Emergency Diesel Engine
In this paper, the finite element analysis model of camshaft for nuclear emergency diesel engine with initial crack defect is established based on ABAQUS finite element analysis software. The effects of initial crack defect parameters on crack tip stress intensity factor are studied by a working condition discretization method. The numerical results show that the crack tip stress intensity factors of transverse crack and longitudinal crack are quite different in a load cycle of camshaft. The crack tip stress intensity factors of transverse crack fluctuate greatly, and the crack tip stress intensity factor range is much larger than that of longitudinal crack, which indicates that the fatigue fracture risk of transverse crack on the camshaft journal is higher. With the increase of initial crack depth from 1 mm to 4 mm, the crack tip stress intensity factor range increases from 410.84 MPa·mm1/2 to 720.24 MPa·mm1/2 by 75.3%, which indicates that the increase of initial crack depth can lead to a significant increase of the fatigue fracture risk. As the initial crack defect moves away from the cam, the maximum of the crack tip stress intensity factor initially increases and then decreases after reaching a maximum value. When the initial crack is 3 mm away from the end face of the cam, the crack tip stress intensity factor range is the largest (843.98 MPa·mm1/2), which indicates that the fatigue fracture risk of transverse crack at this position is the highest. The research results obtained in this paper may provide some reference for the fracture assessment and reliability analysis of camshaft for nuclear emergency diesel engine.
- 1 December 2019
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 677 (3) , 032059
Open AccessEffects of Initial Crack Defect on Fatigue Crack Growth of Camshaft for Nuclear Emergency Diesel Engine
In this paper, the finite element analysis model of camshaft for nuclear emergency diesel engine with initial crack defect is established based on ABAQUS finite element analysis software. The effects of initial crack defect parameters on crack tip stress intensity factor are studied by a working condition discretization method. The numerical results show that the crack tip stress intensity factors of transverse crack and longitudinal crack are quite different in a load cycle of camshaft. The crack tip stress intensity factors of transverse crack fluctuate greatly, and the crack tip stress intensity factor range is much larger than that of longitudinal crack, which indicates that the fatigue fracture risk of transverse crack on the camshaft journal is higher. With the increase of initial crack depth from 1 mm to 4 mm, the crack tip stress intensity factor range increases from 410.84 MPa·mm1/2 to 720.24 MPa·mm1/2 by 75.3%, which indicates that the increase of initial crack depth can lead to a significant increase of the fatigue fracture risk. As the initial crack defect moves away from the cam, the maximum of the crack tip stress intensity factor initially increases and then decreases after reaching a maximum value. When the initial crack is 3 mm away from the end face of the cam, the crack tip stress intensity factor range is the largest (843.98 MPa·mm1/2), which indicates that the fatigue fracture risk of transverse crack at this position is the highest. The research results obtained in this paper may provide some reference for the fracture assessment and reliability analysis of camshaft for nuclear emergency diesel engine.