Avinash Lahgere
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Avinash Lahgere has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Hafeez Raza
Department of Electrical Engineering, Indian Institute of Technology Kanpur, Kanpur, India
6 shared publications - Hussam Amrouch
Technical University of Munich
6 shared publications - Yogesh Singh Chauhan
Indian Institute of Technology (IIT) Kanpur
5 shared publications - Mamidala Jagadesh Kumar
IETE Technical Review
3 shared publications - Neha Kamal
Startup Incubation and Innovation Center, Indian Institute of Technology Kanpur, Kanpur, India
3 shared publications - Alok Kumar Kamal
Department of Electrical and Electronics Engineering, ABV IIITM Gwalior, Gwalior, Madhya Pradesh, India
2 shared publications
Latest Publications
- Open Access
- 13 July 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (3)
Comprehensive TCAD-based geometry study on self-aligned coplanar top gate a-IGZO TFTs
Amorphous oxide semiconductor-based thin-film transistors (TFTs) are preferred for large-area, high-resolution displays and memory applications owing to their superior electrical properties. However, the geometry of TFTs plays a vital role in determining the device characteristics. In this study, we present a comprehensive study of the impact of planar and stepped self-aligned coplanar geometry designs on the digital circuit performance. We adopted a mixed-mode simulation approach using technology computer-aided design simulations to design logic gates and a three-stage ring oscillator (RO) circuit. The results indicate that the stepped geometry shows better switching performance with a higher gain of 15.45 V/V but exhibits a lower oscillation frequency (fosc ∼ 6.25 MHz), which is nearly half of the planar geometry (fosc ∼ 14.5 MHz). Here, we present a simplified methodology that relates geometry electrostatics, and parasitic components to the RO circuit delay response. The calculated propagation delay of stepped geometry is 2.31 times that of planar geometry, which results in higher fosc in planar geometry. A lower depletion capacitance (resulting from reduced dopant diffusion) and comparable accumulation capacitance (slope extension profile) indicate better gate control in stepped geometry. However, the threshold voltage is the primary factor that mainly contributes to the effective resistance of the geometry and affects fosc and the switching behavior.
- 13 July 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (3)
Open AccessComprehensive TCAD-based geometry study on self-aligned coplanar top gate a-IGZO TFTs
Amorphous oxide semiconductor-based thin-film transistors (TFTs) are preferred for large-area, high-resolution displays and memory applications owing to their superior electrical properties. However, the geometry of TFTs plays a vital role in determining the device characteristics. In this study, we present a comprehensive study of the impact of planar and stepped self-aligned coplanar geometry designs on the digital circuit performance. We adopted a mixed-mode simulation approach using technology computer-aided design simulations to design logic gates and a three-stage ring oscillator (RO) circuit. The results indicate that the stepped geometry shows better switching performance with a higher gain of 15.45 V/V but exhibits a lower oscillation frequency (fosc ∼ 6.25 MHz), which is nearly half of the planar geometry (fosc ∼ 14.5 MHz). Here, we present a simplified methodology that relates geometry electrostatics, and parasitic components to the RO circuit delay response. The calculated propagation delay of stepped geometry is 2.31 times that of planar geometry, which results in higher fosc in planar geometry. A lower depletion capacitance (resulting from reduced dopant diffusion) and comparable accumulation capacitance (slope extension profile) indicate better gate control in stepped geometry. However, the threshold voltage is the primary factor that mainly contributes to the effective resistance of the geometry and affects fosc and the switching behavior.
- 1 May 2026
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 41 (5) , 055004
Efficacy of π -gate in LDMOS for improved safe operating area and figure of merits
In this work, we propose a novel π -gate laterally diffused MOS ( π -LDMOS) structure optimized for high-voltage (HV) applications. A comprehensive device-level investigation is carried out using a well-calibrated TCAD simulation framework. The study systematically explores the trade-offs among critical performance metrics relevant to both analog and digital domains, as well as the device’s safe operating area. The proposed device exhibits a 23 % enhancement in breakdown voltage ( V BR ) with only a 6 % increase in on-resistance ( R ON ) at gate to source voltage ( V GS ) of 1.8 V, when compared to the standard LDMOS (std-LDMOS). Furthermore, the proposed π -LDMOS demonstrates a 90 % improvement in cut-off frequency ( f t ) and a 200 % increase in intrinsic gain ( g m / g ds ) at V GS = 1.8 V. These enhancements are primarily attributed to significant reductions in gate capacitance ( C gg ) and output conductance ( g ds ), while maintaining a similar transconductance ( g m ) relative to the std-LDMOS. As a result, the π -LDMOS achieves 43 % and 65 % improvements in Baliga’s and Johnson’s figures of merit, respectively. Overall, the proposed π -LDMOS exhibits superior performance, positioning it as a strong candidate for both analog and HV power applications.
- 1 May 2026
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 41 (5) , 055004
Efficacy of π -gate in LDMOS for improved safe operating area and figure of merits
In this work, we propose a novel π -gate laterally diffused MOS ( π -LDMOS) structure optimized for high-voltage (HV) applications. A comprehensive device-level investigation is carried out using a well-calibrated TCAD simulation framework. The study systematically explores the trade-offs among critical performance metrics relevant to both analog and digital domains, as well as the device’s safe operating area. The proposed device exhibits a 23 % enhancement in breakdown voltage ( V BR ) with only a 6 % increase in on-resistance ( R ON ) at gate to source voltage ( V GS ) of 1.8 V, when compared to the standard LDMOS (std-LDMOS). Furthermore, the proposed π -LDMOS demonstrates a 90 % improvement in cut-off frequency ( f t ) and a 200 % increase in intrinsic gain ( g m / g ds ) at V GS = 1.8 V. These enhancements are primarily attributed to significant reductions in gate capacitance ( C gg ) and output conductance ( g ds ), while maintaining a similar transconductance ( g m ) relative to the std-LDMOS. As a result, the π -LDMOS achieves 43 % and 65 % improvements in Baliga’s and Johnson’s figures of merit, respectively. Overall, the proposed π -LDMOS exhibits superior performance, positioning it as a strong candidate for both analog and HV power applications.
- 20 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (6) , 3557-3564
Revisiting Negative Capacitance Effect for 1T-DRAM Application
In this article, we present a highly scaled one-transistor dynamic random access memory (1T-DRAM) cell using the ferroelectric (FE) material exploiting the negative capacitance (NC) effect. The Landau–Khalatnikov (L–K) model parameters have been accurately calibrated to fit the simulated S-curve to the experimentally reported hysteresis characteristics. The proposed 1T-DRAM device utilizes the voltage amplification due to the NC effect for better memory performance on less supply voltage and shorter gate lengths as compared to existing 1T-DRAMs. At 300 K, the proposed 1T-DRAM provides a reliable sense margin (SM) ~ $0.7~\mu $ A/ $\mu $ m, which is sufficient for embedded DRAM applications, exhibits high write speed due to steep switching caused by the NC effect, a larger retention time (RT) of ~50 ms that is ~ $10\times $ larger than the baseline 1T-DRAM, and also higher read current ratio ( ${I}_{{R}{1}}/{I}_{{R}{0}}$ ). Moreover, at 358 K, the proposed 1T-DRAM shows the SM of ~ $0.65~\mu $ A/ $\mu $ m. The retention of proposed 1T-DRAM at 358 K is 20 ms, which is ~ $40\times $ higher than the baseline 1T-DRAM. Furthermore, the performance analysis of the proposed 1T-DRAM has been carried out through TCAD simulations on ${2}\times {2}$ crossbar memory array level at 300 and 358 K.
- 20 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (6) , 3557-3564
Revisiting Negative Capacitance Effect for 1T-DRAM Application
In this article, we present a highly scaled one-transistor dynamic random access memory (1T-DRAM) cell using the ferroelectric (FE) material exploiting the negative capacitance (NC) effect. The Landau–Khalatnikov (L–K) model parameters have been accurately calibrated to fit the simulated S-curve to the experimentally reported hysteresis characteristics. The proposed 1T-DRAM device utilizes the voltage amplification due to the NC effect for better memory performance on less supply voltage and shorter gate lengths as compared to existing 1T-DRAMs. At 300 K, the proposed 1T-DRAM provides a reliable sense margin (SM) ~ $0.7~\mu $ A/ $\mu $ m, which is sufficient for embedded DRAM applications, exhibits high write speed due to steep switching caused by the NC effect, a larger retention time (RT) of ~50 ms that is ~ $10\times $ larger than the baseline 1T-DRAM, and also higher read current ratio ( ${I}_{{R}{1}}/{I}_{{R}{0}}$ ). Moreover, at 358 K, the proposed 1T-DRAM shows the SM of ~ $0.65~\mu $ A/ $\mu $ m. The retention of proposed 1T-DRAM at 358 K is 20 ms, which is ~ $40\times $ higher than the baseline 1T-DRAM. Furthermore, the performance analysis of the proposed 1T-DRAM has been carried out through TCAD simulations on ${2}\times {2}$ crossbar memory array level at 300 and 358 K.
- 10 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. PP (00189383) , 1-8
Soft Error Analysis in NSFET and FSFET: From Device Physics to Circuit and Memory Impact
We investigate the single event upset (SEU) reliability of nanosheet field-effect transistors (NSFETs) and forksheet field-effect transistors (FSFETs). Calibrated TCAD and BSIM compact models are used to assess heavy-ion radiation (HIR) impact from device to circuit level. First, we investigate the impact of HIR on the device characteristics in TCAD and reveal that due to higher recombination rates, the collected charge for FSFET is lower than NSFET. Peak current and collection time for FSFET are also lower for all linear energy transfer (LET) and V DD, hence achieving a better bipolar gain ( $\beta $ ). At the circuit level, the comparison is based on metrics including masking efficiency ( $\eta $ ), critical LET (LETCrit), SEU cross section (SCS), and soft error rate (SER) for inverter chains, D flip-flops (DFFs), and static random access memories (SRAMs). The FSFET achieves $\eta \ge 0.60$ , and shows masking higher than the NSFET. The logic LETCrit at 0.70 V, improves by 34.80%, and the probability of error-latching by 33% with FSFET. At 0.70 V, SRAM LETCrit with NSFET is 18.36% worse than the FSFET. Next, we compare SER for HIR exposure: 1) at sea-level, 2) in geosynchronous/geostationary orbits, and 3) for a solar-flare event. FSFET logic outperforms NSFET, with a 52% lower SER at the sea-level. For memory circuits, the improvement is 8.81%. The SEU susceptibility of FSFET increases for oblique and transverse strikes due to the compact n-/p-FET packing, highlighting the need for appropriate radiation-hardened circuit design.
- 10 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. PP (00189383) , 1-8
Soft Error Analysis in NSFET and FSFET: From Device Physics to Circuit and Memory Impact
We investigate the single event upset (SEU) reliability of nanosheet field-effect transistors (NSFETs) and forksheet field-effect transistors (FSFETs). Calibrated TCAD and BSIM compact models are used to assess heavy-ion radiation (HIR) impact from device to circuit level. First, we investigate the impact of HIR on the device characteristics in TCAD and reveal that due to higher recombination rates, the collected charge for FSFET is lower than NSFET. Peak current and collection time for FSFET are also lower for all linear energy transfer (LET) and V DD, hence achieving a better bipolar gain ( $\beta $ ). At the circuit level, the comparison is based on metrics including masking efficiency ( $\eta $ ), critical LET (LETCrit), SEU cross section (SCS), and soft error rate (SER) for inverter chains, D flip-flops (DFFs), and static random access memories (SRAMs). The FSFET achieves $\eta \ge 0.60$ , and shows masking higher than the NSFET. The logic LETCrit at 0.70 V, improves by 34.80%, and the probability of error-latching by 33% with FSFET. At 0.70 V, SRAM LETCrit with NSFET is 18.36% worse than the FSFET. Next, we compare SER for HIR exposure: 1) at sea-level, 2) in geosynchronous/geostationary orbits, and 3) for a solar-flare event. FSFET logic outperforms NSFET, with a 52% lower SER at the sea-level. For memory circuits, the improvement is 8.81%. The SEU susceptibility of FSFET increases for oblique and transverse strikes due to the compact n-/p-FET packing, highlighting the need for appropriate radiation-hardened circuit design.
- 29 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Computers
- Vol. 75 (3) , 1197-1208
Evaluation of Radiation Resilience, Performance, and V min of Sub-3 nm FSFET Based SRAM Arrays
In this work, we present single-event upset (SEU) analysis for Forksheet FET (FSFET) based CMOS circuits. Next, we present an array-level power and performance analysis along with the Vmin evaluation for the FSFET-based SRAM. Physics-based TCAD and industry-standard BSIM-CMG compact models are calibrated for accurate circuit analysis in SPICE. The impact of varying Heavy-Ion Radiation (HIR) doses and strike orientations is investigated for the FSFETs. The robustness of CMOS inverter against HIR is also reported in terms of failure time (tfail) and output voltage swing ($\Delta$ VDrop). For the SRAM, we determine the critical Linear Energy Transfer (LET). For FSFET, the individual n-/p-FETs are more vulnerable to the irradiation incident on nearby devices. At the circuit level, in comparison to perpendicular strikes, the$\Delta$ VDrop increases by 1.25 V and 2.75 V respectively, for oblique and transverse incidences, at a dose of 2.0 MeVcm$^2$ /mg. The tfail also increases by 43% and 60% and the SRAM critical LET also decreases by 85% and 57.5%, respectively. The array level SRAM evaluation shows that the FSFET enables reliable operation with low-power consumption, impressive noise margins, and low minimum-operating voltage (Vmin) values. FSFET SRAM power dissipation during the read and write operations is as low as 7.02$\mu$ W, and 3.00$\mu$ W respectively. At VDD$=$ 0.70 V, the noise margins for hold, read, and write operations are 289.27 mV, 122.89 mV, and 297.79 mV. The Vmin for read and write operations are 0.30 V and 0.35 V respectively.- 29 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Computers
- Vol. 75 (3) , 1197-1208
Evaluation of Radiation Resilience, Performance, and V min of Sub-3 nm FSFET Based SRAM Arrays
In this work, we present single-event upset (SEU) analysis for Forksheet FET (FSFET) based CMOS circuits. Next, we present an array-level power and performance analysis along with the Vmin evaluation for the FSFET-based SRAM. Physics-based TCAD and industry-standard BSIM-CMG compact models are calibrated for accurate circuit analysis in SPICE. The impact of varying Heavy-Ion Radiation (HIR) doses and strike orientations is investigated for the FSFETs. The robustness of CMOS inverter against HIR is also reported in terms of failure time (tfail) and output voltage swing ($\Delta$ VDrop). For the SRAM, we determine the critical Linear Energy Transfer (LET). For FSFET, the individual n-/p-FETs are more vulnerable to the irradiation incident on nearby devices. At the circuit level, in comparison to perpendicular strikes, the$\Delta$ VDrop increases by 1.25 V and 2.75 V respectively, for oblique and transverse incidences, at a dose of 2.0 MeVcm$^2$ /mg. The tfail also increases by 43% and 60% and the SRAM critical LET also decreases by 85% and 57.5%, respectively. The array level SRAM evaluation shows that the FSFET enables reliable operation with low-power consumption, impressive noise margins, and low minimum-operating voltage (Vmin) values. FSFET SRAM power dissipation during the read and write operations is as low as 7.02$\mu$ W, and 3.00$\mu$ W respectively. At VDD$=$ 0.70 V, the noise margins for hold, read, and write operations are 289.27 mV, 122.89 mV, and 297.79 mV. The Vmin for read and write operations are 0.30 V and 0.35 V respectively.- 23 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (9) , 4780-4787
Physics-Based SPICE Model of Slant Field Plate GaN HEMTs
This article introduces a SPICE-compatible compact model for GaN HEMTs with slant field plates (FPs), implemented using the ASM-HEMT framework. The slant FP geometry, critical for optimizing electric field distribution and breakdown performance, is approximated as a multistep gate FP structure. It is shown that conventional HEMT models using normal gate FPs fail to accurately capture the capacitance behavior of these devices. To address this limitation, a new modeling methodology is developed within the ASM-HEMT framework. This approach ensures accurate simulation of device behavior while maintaining computational efficiency. Validated against TCAD simulations and experimental data, the model demonstrates strong agreement across pulsed I–V, C–V, and large-signal RF load–pull characteristics.
- 23 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (9) , 4780-4787
Physics-Based SPICE Model of Slant Field Plate GaN HEMTs
This article introduces a SPICE-compatible compact model for GaN HEMTs with slant field plates (FPs), implemented using the ASM-HEMT framework. The slant FP geometry, critical for optimizing electric field distribution and breakdown performance, is approximated as a multistep gate FP structure. It is shown that conventional HEMT models using normal gate FPs fail to accurately capture the capacitance behavior of these devices. To address this limitation, a new modeling methodology is developed within the ASM-HEMT framework. This approach ensures accurate simulation of device behavior while maintaining computational efficiency. Validated against TCAD simulations and experimental data, the model demonstrates strong agreement across pulsed I–V, C–V, and large-signal RF load–pull characteristics.
- Open Access
- 11 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Exploratory Solid-State Computational Devices and Circuits
- Vol. 11, 42-50
An Investigation of Minimum Supply Voltage of 5-nm SRAM From 300 K Down to 10 K
In this article, we present a comprehensive study of the impact of cryogenic temperatures on the minimum-operating voltage (Vmin) of 5 nm Fin Field-Effect Transistors (FinFETs)-based Static Random-Access Memory (SRAM) cells. To perform the SRAM Vmin evaluation, we have measured the FinFETs fabricated using a commercial 5 nm technology down to 10 K. Next, we calibrate a cryogenic aware BSIM-CMG FinFET compact model, which we use with our SRAM evaluation framework. For a comprehensive study, we evaluate three industry-standard SRAM cell types - (i) high-density cell (HDC), (ii) low-voltage cell (LVC), and (iii) high-performance cell (HPC). We analyze the impact of the threshold voltage (VTH) and Gate Length (LG)-only variations on the SRAM noise resilience. At cryogenic temperatures minimum-read voltage (Vmin,R) = 0.15V (62% decrease from room temperature) and minimum-write voltage (Vmin,W) = 0.45V is achieved without read/write assist circuits. We also highlight that the LVC cell provides the best trade-off for Vmin between read and write operations for low-power cryogenic applications.
- 11 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Exploratory Solid-State Computational Devices and Circuits
- Vol. 11, 42-50
Open AccessAn Investigation of Minimum Supply Voltage of 5-nm SRAM From 300 K Down to 10 K
In this article, we present a comprehensive study of the impact of cryogenic temperatures on the minimum-operating voltage (Vmin) of 5 nm Fin Field-Effect Transistors (FinFETs)-based Static Random-Access Memory (SRAM) cells. To perform the SRAM Vmin evaluation, we have measured the FinFETs fabricated using a commercial 5 nm technology down to 10 K. Next, we calibrate a cryogenic aware BSIM-CMG FinFET compact model, which we use with our SRAM evaluation framework. For a comprehensive study, we evaluate three industry-standard SRAM cell types - (i) high-density cell (HDC), (ii) low-voltage cell (LVC), and (iii) high-performance cell (HPC). We analyze the impact of the threshold voltage (VTH) and Gate Length (LG)-only variations on the SRAM noise resilience. At cryogenic temperatures minimum-read voltage (Vmin,R) = 0.15V (62% decrease from room temperature) and minimum-write voltage (Vmin,W) = 0.45V is achieved without read/write assist circuits. We also highlight that the LVC cell provides the best trade-off for Vmin between read and write operations for low-power cryogenic applications.
- Open Access
- 13 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Evaluation of Radiation Resilience, Performance, and V min of Sub-3 nm FSFET based SRAM Arrays
In this work, we present single-event upset (SEU) analysis for Forksheet FET (FSFET) based CMOS circuits. Next, we present an array-level power and performance analysis along with the V min evaluation for the FSFET-based SRAM. Physicsbased TCAD and industry-standard BSIM-CMG compact models are calibrated for accurate circuit analysis in SPICE. The impact of varying Heavy-Ion Radiation (HIR) doses and strike orientations is investigated for the FSFETs. The robustness of CMOS inverter against HIR is also reported in terms of failure time (t fail) and output voltage swing (∆VDrop). For the SRAM, we determine the critical Linear Energy Transfer (LET). For FSFET, the individual n-/p-FETs are more vulnerable to the irradiation incident on nearby devices. At the circuit level, in comparison to perpendicular strikes, the ∆VDrop increases by 1.25 V and 2.75 V respectively, for oblique and transverse incidences, at a dose of 2.0 MeVcm 2 /mg. The t fail also increases by 43% and 60% and the SRAM critical LET also decreases by 85% and 57.5%, respectively. The array level SRAM evaluation shows that the FSFET enables reliable operation with low-power consumption, impressive noise margins, and low minimumoperating voltage (V min) values. FSFET SRAM power dissipation during the read and write operations is as low as 7.02 µW, and 3.00 µW respectively. At VDD=0.70 V, the noise margins for hold, read, and write operations are 289.27 mV, 122.89 mV, and 297.79 mV. The V min for read and write operations are 0.30 V and 0.35 V respectively.
- 13 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessEvaluation of Radiation Resilience, Performance, and V min of Sub-3 nm FSFET based SRAM Arrays
In this work, we present single-event upset (SEU) analysis for Forksheet FET (FSFET) based CMOS circuits. Next, we present an array-level power and performance analysis along with the V min evaluation for the FSFET-based SRAM. Physicsbased TCAD and industry-standard BSIM-CMG compact models are calibrated for accurate circuit analysis in SPICE. The impact of varying Heavy-Ion Radiation (HIR) doses and strike orientations is investigated for the FSFETs. The robustness of CMOS inverter against HIR is also reported in terms of failure time (t fail) and output voltage swing (∆VDrop). For the SRAM, we determine the critical Linear Energy Transfer (LET). For FSFET, the individual n-/p-FETs are more vulnerable to the irradiation incident on nearby devices. At the circuit level, in comparison to perpendicular strikes, the ∆VDrop increases by 1.25 V and 2.75 V respectively, for oblique and transverse incidences, at a dose of 2.0 MeVcm 2 /mg. The t fail also increases by 43% and 60% and the SRAM critical LET also decreases by 85% and 57.5%, respectively. The array level SRAM evaluation shows that the FSFET enables reliable operation with low-power consumption, impressive noise margins, and low minimumoperating voltage (V min) values. FSFET SRAM power dissipation during the read and write operations is as low as 7.02 µW, and 3.00 µW respectively. At VDD=0.70 V, the noise margins for hold, read, and write operations are 289.27 mV, 122.89 mV, and 297.79 mV. The V min for read and write operations are 0.30 V and 0.35 V respectively.
- 13 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 25 (1) , 156-162
Comprehensive TCAD-Based Single Event Effect Study of TFET-Based 1T DRAM and Crossbar Memory Array
In this paper, a comprehensive TCAD-based single event effect (SEE) study on tunnel field effect transistor (TFET) based one transistor dynamic random access memory (1T DRAM) and crossbar memory array is demonstrated through well-calibrated 2-D TCAD simulations. The simulation study reveals that the regions near Gate 2 are more susceptible to SEE. In addition, in comparison to without SEE, when a high energy particle (HEP) strikes the device, the read “1" (R1) current remains the same, however, the read “0" (R0) current increases 10× at 358 K. As a result, the read current ratio (IR1/IR0) and the sense margin (SM) decreases. The IR1/IR0 ratio with SEE is found to be 10, which is 10× lower than ratio without SEE. In addition, the impact of various parameters such as linear energy transfer (LET), HEP strike time, HEP strike moment, and HEP radius on TFET-based 1T DRAM performance is also evaluated. Moreover, for a 2 x 2 crossbar memory array, the combination of SEE with word line disturbance mechanism causes 10× reduction in the R1 current at 358 K. Our findings will pave the way for further exploration and designing radiation-hardened TFET-based 1T DRAM for future low-power space applications.
- 13 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 25 (1) , 156-162
Comprehensive TCAD-Based Single Event Effect Study of TFET-Based 1T DRAM and Crossbar Memory Array
In this paper, a comprehensive TCAD-based single event effect (SEE) study on tunnel field effect transistor (TFET) based one transistor dynamic random access memory (1T DRAM) and crossbar memory array is demonstrated through well-calibrated 2-D TCAD simulations. The simulation study reveals that the regions near Gate 2 are more susceptible to SEE. In addition, in comparison to without SEE, when a high energy particle (HEP) strikes the device, the read “1" (R1) current remains the same, however, the read “0" (R0) current increases 10× at 358 K. As a result, the read current ratio (IR1/IR0) and the sense margin (SM) decreases. The IR1/IR0 ratio with SEE is found to be 10, which is 10× lower than ratio without SEE. In addition, the impact of various parameters such as linear energy transfer (LET), HEP strike time, HEP strike moment, and HEP radius on TFET-based 1T DRAM performance is also evaluated. Moreover, for a 2 x 2 crossbar memory array, the combination of SEE with word line disturbance mechanism causes 10× reduction in the R1 current at 358 K. Our findings will pave the way for further exploration and designing radiation-hardened TFET-based 1T DRAM for future low-power space applications.