IMIman Monsef

Iman Monsef

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Iman Monsef has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Magnetite Texture and Geochemistry in the Takab Ore Deposit (NW Iran): Implications for a Complex Hydrothermal Evolution

    by Christiane Wagner, Omar Boudouma, Nicolas Rividi, Beate Orberger, Ghasem Nabatian, Maryam Honarmand, Iman Monsef

    The massive magnetite deposit from Takab (NW Iran) is hosted in amphibolite layers intercalated with the chemical and terrigenous sediments of the Takab BIF. A comprehensive textural and chemical study allowed three types of magnetite (Mt) to be distinguished. Mt1 forms large (≤1 mm) inhomogeneous grains surrounded and locally invaded by magnetite Mt2. Oscillatory zoning is present in Mt1 and Mt2. Mt3 forms bands aligned along fracture planes. Mt3 may contain hematite relicts and is porous in proximity to hematite. Mt1 shows variable and higher Si (up to 1.4 wt. %), Al, Ca, and Mg and lower Fe content (68 wt. %) than Mt2. Mt3 has the lowest Si (<0.3 wt. %) and highest Fe (71 wt. %) contents. The temperature of formation decreases from Mt1 (600 °C) to Mt2 (500–550 °C) and Mt3 (380–440 °C). Mt1 likely formed in a reducing Si-rich environment. The close spatial relationship, sharp compositional boundaries, similar crystallographic structure of Mt1 and Mt2, and porosity in Mt2 suggest a fluid-assisted coupled dissolution of Mt1 and precipitation of Mt2 (CDR process). Microfracturing allowed the penetration of oxidizing fluid and the formation of platy hematite bands. Mt3 (mushketovite) formed after hematite by interaction with a reducing lower temperature fluid through a redox transformation.


  • Open Access

    Magnetite–Hematite Characterization at Micron Scale with Implications for Metallurgical Processing and Decarbonization

    by Beate Orberger, Christiane Wagner, Omar Boudouma, Nicolas Rividi, Christine Bauer, Rebecca Wagner, Ghasem Nabatian, Maryam Honarmand, Iman Monsef

    Magnetite deposits represent important iron ore resources. Selective sorting of valuables from gangue and targeting of potential critical metals that can be recovered from waste streams must be implemented from the exploration and excavation steps onwards. Optical and scanning electron microscopy, electron microprobe analysis, dual-energy X-ray transmission, and computed tomography were applied to determine the mineralogy and classify the iron oxides of different iron ore types. These characteristics can be used for sorting at the exploration and extraction steps to reduce unvaluable materials at the loading and hauling steps, which contribute about 50% of the greenhouse gas emissions of the iron ore mining and mineral processing sector. These data also contribute to fine-tuning mineral processing parameters.

  • Open Access

    In Situ Trace Element and Fe-O Isotope Studies on Magnetite of the Iron-Oxide Ores from the Takab Region, North Western Iran: Implications for Ore Genesis

    by Christiane Wagner, Johan Villeneuve, Omar Boudouma, Nicolas Rividi, Beate Orberger, Ghasem Nabatian, Maryam Honarmand, Iman Monsef

    The early Cambrian Takab iron ore deposit is situated in the northern part of the Sanandaj-Sirjan zone, western Iran. It consists of banded, nodular and disseminated magnetite hosted in folded micaschists. Trace element and Fe and O isotopic experiments reveal various hydrothermal precipitation environments under reduced to slightly oxidizing conditions. Disseminated magnetite has high Ti (945–1940 ppm) positively correlated with Mg + Al + Si, and heavy Fe (+0.76 to +1.86‰) and O (+1.0 to +4.07‰) isotopic compositions that support a magmatic/high-T hydrothermal origin. Banded magnetite has low Ti (15−200 ppm), V (≤100 ppm), Si and Mg (mostly ≤300 ppm) and variable Al. The ∂56Fe values vary from −0.2‰ to +1.12‰ but most values also support a magmatic/high-T hydrothermal origin. However, variable ∂18O (−2.52 to +1.22‰) values provide evidence of re-equilibration with lower-T fluid at ~200–300 °C. Nodular magnetite shows high Mn (≤1%), and mostly negative ∂56Fe values (average, −0.3‰) indicative of precipitation from an isotopically light hydrothermal fluid. Re-equilibration with carbonated rocks/fluids likely results in a negative Ce anomaly and higher ∂18O (average, +6.30‰). The Takab iron ore deposit has, thus, experienced a complex hydrothermal history.


  • Open Access

    Potential of Dual and Multi Energy XRT and CT Analyses on Iron Formations

    by Christine Bauer, Rebecca Wagner, Beate Orberger, Markus Firsching, Alexander Ennen, Carlos Garcia Pina, Christiane Wagner, Maryam Honarmand, Ghasem Nabatian, Iman Monsef

    Dual and multi energy X-ray transmission imaging (DE-/ME-XRT) are powerful tools to acquire quantitative material characteristics of diverse samples without destruction. As those X-ray imaging techniques are based on the projection onto the imaging plane, only two-dimensional data can be obtained. To acquire three-dimensional information and a complete examination on topology and spatial trends of materials, computed tomography (CT) can be used. In combination, these methods may offer a robust non-destructive testing technique for research and industrial applications. For example, the iron ore mining and processing industry requires the ratio of economic iron minerals to siliceous waste material for resource and reserve estimations, and for efficient sorting prior to beneficiation, to avoid equipment destruction due to highly abrasive quartz. While XRT provides information concerning the thickness, areal density and mass fraction of iron and the respective background material, CT may deliver size, distribution and orientation of internal structures. Our study shows that the data provided by XRT and CT is reliable and, together with data processing, can be successfully applied for distinguishing iron oxide rich parts from waste. Furthermore, heavy element bearing minerals such as baryte, uraninite, galena and monazite can be detected.