Bhabatosh Biswas
Research Subjects
Bhabatosh Biswas has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Arijit Sinha
Department of Metallurgical Engineering, Kazi Nazrul University, Asansol, India
9 shared publications Bhairab Chandra Mitra
Indian Institute of Engineering Science and Technology, Shibpur
7 shared publicationsSumit Chabri
Department of Metallurgy and Materials Engineering; Indian Institute of Engineering Science and Technology; Shibpur Howrah 711103 India
6 shared publicationsNil Ratan Bandyopadhyay
Indian Institute of Engineering Science and Technology, Shibpur
4 shared publicationsPravin Sawai
Indian Institute of Technology
4 shared publicationsKunal Das
Centre for NDE; Sathyabama University; Chennai 600119 India
3 shared publications
Latest Publications
- 2 July 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 236 (2) , 242-249
Indentation behavior of cellulosic fibers/fly ash-incorporated polymer composites at sub-micron scale
Chemically treated short cellulosic fibers (jute and sisal) reinforced heat-treated silanized fly ash-dispersed hybrid polymer composites were synthesized by a compression molding technique. The 35 wt.% filler loading unsaturated polyester matrix-based composites were fabricated. The mechanical behavior of the unsaturated polyester matrix and unsaturated polyester-based composites was successfully assessed at the sub-micron length scale using the nanoindentation or depth-sensing instrumented indentation technique. It was observed that along with filler addition, the mechanical properties at the sub-micron scale improved significantly. A successful attempt to investigate the effect of filler inclusion within the unsaturated polyester matrix through various nanoindentation-derived parameters, namely, nanohardness, reduced modulus, elastic recovery, residual depth, wear rate as well the dynamic mechanical properties was also executed in the current investigation.
- 2 July 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 236 (2) , 242-249
Indentation behavior of cellulosic fibers/fly ash-incorporated polymer composites at sub-micron scale
Chemically treated short cellulosic fibers (jute and sisal) reinforced heat-treated silanized fly ash-dispersed hybrid polymer composites were synthesized by a compression molding technique. The 35 wt.% filler loading unsaturated polyester matrix-based composites were fabricated. The mechanical behavior of the unsaturated polyester matrix and unsaturated polyester-based composites was successfully assessed at the sub-micron length scale using the nanoindentation or depth-sensing instrumented indentation technique. It was observed that along with filler addition, the mechanical properties at the sub-micron scale improved significantly. A successful attempt to investigate the effect of filler inclusion within the unsaturated polyester matrix through various nanoindentation-derived parameters, namely, nanohardness, reduced modulus, elastic recovery, residual depth, wear rate as well the dynamic mechanical properties was also executed in the current investigation.
- 20 March 2019
- Published by Springer Nature in Cellulose
- Vol. 26 (7) , 4445-4461
Thermal stability, swelling and degradation behaviour of natural fibre based hybrid polymer composites
- 20 March 2019
- Published by Springer Nature in Cellulose
- Vol. 26 (7) , 4445-4461
Thermal stability, swelling and degradation behaviour of natural fibre based hybrid polymer composites
- 4 December 2018
- Published by Wiley in Polymer Composites
- Vol. 40 (7) , 2790-2801
Influence of ZrO2 Incorporation on Sisal Fiber Reinforced Unsaturated Polyester Composites
Sisal fiber along with ZrO2 particles dispersed unsaturated polyester (UP) composites were fabricated by compression molding technique. The filler contents were varied from 5 to 45 wt% with a gradual increase of 10%. The structural investigation was done using Scanning electron microscopy, X‐ray diffraction, and Fourier transform infrared spectroscopy. Mechanical testing was performed through microhardness tester, tensile, flexural, and Izod impact test. The optimum mechanical properties were obtained at 35 wt% of filler incorporation within UP matrix followed by a slight deterioration at 45 wt%. Fractographic images of the composites display the phenomena of fiber pull‐out, debonding and breakage. The water absorption test was performed both at room temperature and boiling water temperature conditions. The thermal insulation measurement was performed by Kawabata method. POLYM. COMPOS., 40:2790–2801, 2019. © 2018 Society of Plastics Engineers
- 4 December 2018
- Published by Wiley in Polymer Composites
- Vol. 40 (7) , 2790-2801
Influence of ZrO2 Incorporation on Sisal Fiber Reinforced Unsaturated Polyester Composites
Sisal fiber along with ZrO2 particles dispersed unsaturated polyester (UP) composites were fabricated by compression molding technique. The filler contents were varied from 5 to 45 wt% with a gradual increase of 10%. The structural investigation was done using Scanning electron microscopy, X‐ray diffraction, and Fourier transform infrared spectroscopy. Mechanical testing was performed through microhardness tester, tensile, flexural, and Izod impact test. The optimum mechanical properties were obtained at 35 wt% of filler incorporation within UP matrix followed by a slight deterioration at 45 wt%. Fractographic images of the composites display the phenomena of fiber pull‐out, debonding and breakage. The water absorption test was performed both at room temperature and boiling water temperature conditions. The thermal insulation measurement was performed by Kawabata method. POLYM. COMPOS., 40:2790–2801, 2019. © 2018 Society of Plastics Engineers
- 1 April 2018
- Published by Wiley in Advances in Polymer Technology
- Vol. 37 (3) , 810-821
Effect of Aluminum Addition on the Mechanical and Thermal Behavior of Unsaturated Polyester/Jute Composites
- 1 April 2018
- Published by Wiley in Advances in Polymer Technology
- Vol. 37 (3) , 810-821
Effect of Aluminum Addition on the Mechanical and Thermal Behavior of Unsaturated Polyester/Jute Composites
- 7 May 2017
- Published by Wiley in Polymer Composites
- Vol. 39 (S1) , E101-E112
Mechanical properties of metal oxide dispersed jute fiber reinforced polyester biocomposites
Enhancement in toughness without reducing its mechanical property is a serious issue in context of application of the biocomposites. Therefore, in this study, the effect of incorporation of Al2O3 and ZrO2 particles in the polymer matrix on the mechanical properties of jute fiber reinforced unsaturated polyester biocomposites were investigated. Reinforcements with fibers were carried out in different weight proportions (5–25%) and with varied fiber lengths. The biocomposites were fabricated using hand lay‐up method. Overall 20 wt % filler content (18 wt% fiber and 2 wt% metal oxide particles) was selected as the optimized composition. The fibers were treated with NaOH solution for better compatibility with matrix whereas the particles were treated with silane for better adherence with the matrix. Microhardness, tensile, flexural, and impact properties of the biocomposites were evaluated as per standard. Fractography of the biocomposites were done using scanning electron microscope. It was found that the ZrO2 particle incorporated bicomposites show better mechanical properties than the Al2O3 dispersed bicomposites. POLYM. COMPOS., 39:E101–E112, 2018. © 2017 Society of Plastics Engineers
- 7 May 2017
- Published by Wiley in Polymer Composites
- Vol. 39 (S1) , E101-E112
Mechanical properties of metal oxide dispersed jute fiber reinforced polyester biocomposites
Enhancement in toughness without reducing its mechanical property is a serious issue in context of application of the biocomposites. Therefore, in this study, the effect of incorporation of Al2O3 and ZrO2 particles in the polymer matrix on the mechanical properties of jute fiber reinforced unsaturated polyester biocomposites were investigated. Reinforcements with fibers were carried out in different weight proportions (5–25%) and with varied fiber lengths. The biocomposites were fabricated using hand lay‐up method. Overall 20 wt % filler content (18 wt% fiber and 2 wt% metal oxide particles) was selected as the optimized composition. The fibers were treated with NaOH solution for better compatibility with matrix whereas the particles were treated with silane for better adherence with the matrix. Microhardness, tensile, flexural, and impact properties of the biocomposites were evaluated as per standard. Fractography of the biocomposites were done using scanning electron microscope. It was found that the ZrO2 particle incorporated bicomposites show better mechanical properties than the Al2O3 dispersed bicomposites. POLYM. COMPOS., 39:E101–E112, 2018. © 2017 Society of Plastics Engineers
- Open Access
- 1 April 2017
- Published by Elsevier in Engineering Science and Technology, an International Journal
- Vol. 20 (2) , 760-774
Effect of functionalized metal oxides addition on the mechanical, thermal and swelling behaviour of polyester/jute composites
- 1 April 2017
- Published by Elsevier in Engineering Science and Technology, an International Journal
- Vol. 20 (2) , 760-774
Open AccessEffect of functionalized metal oxides addition on the mechanical, thermal and swelling behaviour of polyester/jute composites
- 9 August 2016
- Published by Wiley in Polymer Composites
- Vol. 39 (S3) , E1315-E1330
Effect of copper incorporation on the mechanical and thermal behavior of jute fiber reinforced unsaturated polyester composites
Jute fiber along with Cu particle dispersed unsaturated polyester composites having different filler (both Jute and Cu were in equal wt%) loading viz. 2, 5, 10, and 15 wt% were fabricated by compression molding technique. In the present investigation, it is observed that with fillers (Jute and Cu) incorporation the microhardness increases and reaches its maximum at 10 wt% of fillers content followed by slight deterioration at 15 wt%. Structural investigation through X‐ray diffraction, Fourier transforms infrared spectroscopy, and scanning electron microscopy confirms the presence and dispersion of filler. It is observed that with filler addition the crystallinity (%) of the matrix increases which is obtained from X‐ray diffraction pattern. Fourier transform infrared spectroscopy ensured the bonding of fillers with the matrix and detected the presence of moisture. The mechanical testing viz., tensile, flexural, and Izod impact test shows the strength and modulus increase monotonically upto 10 wt% filler addition followed by slight decreases at 15 wt% filler content. The scratch result shows the optimization of strength and toughness of the composites. Thermo‐gravimetric analysis and differential thermo‐gravimetric analysis showed that the thermal stability, degradation temperature, and residual mass significantly increased with fillers addition. The water absorption test (room temperature and boiling temperature) predict a variation in weight with time. POLYM. COMPOS., 39:E1315–E1330, 2018. © 2016 Society of Plastics Engineers
- 9 August 2016
- Published by Wiley in Polymer Composites
- Vol. 39 (S3) , E1315-E1330
Effect of copper incorporation on the mechanical and thermal behavior of jute fiber reinforced unsaturated polyester composites
Jute fiber along with Cu particle dispersed unsaturated polyester composites having different filler (both Jute and Cu were in equal wt%) loading viz. 2, 5, 10, and 15 wt% were fabricated by compression molding technique. In the present investigation, it is observed that with fillers (Jute and Cu) incorporation the microhardness increases and reaches its maximum at 10 wt% of fillers content followed by slight deterioration at 15 wt%. Structural investigation through X‐ray diffraction, Fourier transforms infrared spectroscopy, and scanning electron microscopy confirms the presence and dispersion of filler. It is observed that with filler addition the crystallinity (%) of the matrix increases which is obtained from X‐ray diffraction pattern. Fourier transform infrared spectroscopy ensured the bonding of fillers with the matrix and detected the presence of moisture. The mechanical testing viz., tensile, flexural, and Izod impact test shows the strength and modulus increase monotonically upto 10 wt% filler addition followed by slight decreases at 15 wt% filler content. The scratch result shows the optimization of strength and toughness of the composites. Thermo‐gravimetric analysis and differential thermo‐gravimetric analysis showed that the thermal stability, degradation temperature, and residual mass significantly increased with fillers addition. The water absorption test (room temperature and boiling temperature) predict a variation in weight with time. POLYM. COMPOS., 39:E1315–E1330, 2018. © 2016 Society of Plastics Engineers
- 20 July 2016
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series C
- Vol. 99 (5) , 525-530
Mechanical Behaviour of Aluminium Dispersed Unsaturated Polyester/Jute Composites for Structural Applications
- 20 July 2016
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series C
- Vol. 99 (5) , 525-530
Mechanical Behaviour of Aluminium Dispersed Unsaturated Polyester/Jute Composites for Structural Applications
- 13 February 2016
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series D
- Vol. 98 (1) , 19-25
Effect of Copper/Graphite Addition on Electrical Conductivity and Thermal Insulation of Unsaturated Polyester/Jute Composites
- 13 February 2016
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series D
- Vol. 98 (1) , 19-25
Effect of Copper/Graphite Addition on Electrical Conductivity and Thermal Insulation of Unsaturated Polyester/Jute Composites